Search found 71 matches
- Wed Feb 08, 2017 3:10 pm
- Forum: RF MODULES
- Topic: Orange Module running MULTI protocol
- Replies: 685
- Views: 428833
Re: Orange Module running MULTI protocol
well now the radio wont do anything.. the battery has 11.92 volts... grrrr
- Wed Feb 08, 2017 12:57 pm
- Forum: RF MODULES
- Topic: Orange Module running MULTI protocol
- Replies: 685
- Views: 428833
Re: Orange Module running MULTI protocol
No jhsa, just a dull blue light, i think I let my battery get to low.. I am still learning all this new technology... first time computer radio, first time using LiPos, and first time messing with firmware that wasn't supposed to be messed with, and newish to flying in general.
- Wed Feb 08, 2017 12:50 pm
- Forum: RF MODULES
- Topic: Orange Module running MULTI protocol
- Replies: 685
- Views: 428833
Re: Orange Module running MULTI protocol
Jhsa, yes I just tried to flash the module, it failed and the error message blinked by to fast to find out why it failed. I then turned of the radio to so I could unplug the module, then tried turning the radio back on and only the blue ready light came on very dim... I had that happen to me once ye...
- Wed Feb 08, 2017 11:58 am
- Forum: RF MODULES
- Topic: Orange Module running MULTI protocol
- Replies: 685
- Views: 428833
Re: Orange Module running MULTI protocol
My radio wont turn on... when I turn the power switch to on, the Blue ready light comes on very dim, I have 11.2 Volts at the battery... tried unplugging and re-plugging in the battery and nothing changes. Charging my battery now, will report back when I have a full battery pack.
- Wed Feb 08, 2017 2:03 am
- Forum: RF MODULES
- Topic: Orange Module running MULTI protocol
- Replies: 685
- Views: 428833
Re: Orange Module running MULTI protocol
I am about to through this POS into the trash... Tx and all... I think I just fried my board... I just did every thing Mike said to do... soldered three wires to the Module on the GRND, CLK, and DATA, connected those wires to the TX mod-bay, then I turned the TX on holding both trim buttons APART, p...
- Tue Feb 07, 2017 11:35 pm
- Forum: RF MODULES
- Topic: Orange Module running MULTI protocol
- Replies: 685
- Views: 428833
Re: Orange Module running MULTI protocol
i think i am getting this figured out Mike... from what I understand I solder 3 wires onto pads GRND, CLK, and DATA, these 3 wires go back to the module bay of the radio (corresponding pins) Then I need to pull power from the mod bay to the mod as well... I found a picture explaining the pinout of t...
- Tue Feb 07, 2017 8:36 pm
- Forum: RF MODULES
- Topic: Orange Module running MULTI protocol
- Replies: 685
- Views: 428833
Re: Orange Module running MULTI protocol
I have read it several times and am still just as confused as I was when choosing a computer radio
- Tue Feb 07, 2017 7:00 pm
- Forum: RF MODULES
- Topic: Orange Module running MULTI protocol
- Replies: 685
- Views: 428833
Re: Orange Module running MULTI protocol
Mike, I am still confused... if I solder the wires to GND, CLK, and DATA, where do the other ends of said wires go, back to the radio? the update kit I now have is used to power the module only? and lastly I do have the firmware (Multiprotocol_V1.1.5_OrangeTx.bin) on the sd card in the firmware fold...
- Tue Feb 07, 2017 4:10 pm
- Forum: RF MODULES
- Topic: Orange Module running MULTI protocol
- Replies: 685
- Views: 428833
Re: Orange Module running MULTI protocol
no i have not Mike, because I don't have the equipment to do so... I thought I ordered it along with my Module, but what I ordered was wrong. I ordered the OrangeRX USB Firmware Update Kit for JR/Futaba Style Transmitter Module but was told this is wrong... second problem is I don't have a windows o...
- Tue Feb 07, 2017 3:37 pm
- Forum: RF MODULES
- Topic: Orange Module running MULTI protocol
- Replies: 685
- Views: 428833
Re: Orange Module running MULTI protocol
I am having problems binding my transmitter to a HobbyZone Champ S+. I am using a Turnigy 9xr Pro (Mode 2) with ersky9x-r220 firmware and a OrangeRX 2.4Ghz Telemetry Module For Turnigy 9XR Pro (DSMX/DSM2/Walkera Compatible) with stock firmware. My problem, I can get the receiver to bind to my module...
- Mon Feb 06, 2017 3:00 pm
- Forum: eepSKYe
- Topic: eepskye & eepe binaries for linux won't work in ubuntu 16.04 (Xenial Xerux). How to build eepskye & eepe
- Replies: 5
- Views: 11124
Re: eepskye & eepe binaries for linux won't work in ubuntu 16.04 (Xenial Xerux). How to build eepskye & eepe
I haven't worked in Linux for several years. Now that my main system is running openSUSE Leap 42.2 I have been relearning how to build packages again. What I need to know is where to go to learn how to do a build environment from source code... What packages do I need to install? I keep finding Debi...