openrcforums

Hi Mike ,


Is it later possible to compile a version for the M64?

Marco.

mbtx3 no more noise !!

Thanks Mike !!!

Marco.

MikeB wrote: ↑Fri Nov 17, 2017 3:59 pm Are you asking for more switches as in "PB3" and "PB4" push buttons?
Mike.

Yes!! more Switches.

Mike, in the future is it possible to configure PC0 (PB3), PC4 (PB4), PG5 (PB5) and PB7 (PB7) as extra switches on / off?

Marco.

DC analysis. haptic 3 (Beeper=NORM)

Hi Mike,

Oscilloscope video Noise in Oscilloscope


Image:

I will try to measure in oscilloscope tomorrow. I'm sure it comes in the buzzer line, I remove the beeper wire and it does not happen anymore. My other TX, which has the W020, uses the piezoelectric in series and controlled by a bc547, also the same occurs. But as it is connected to the BC547, it is...

Hi , A strange noise is occurring on the beeper signal input line. This happens when I set the vibration, it seems that there is another parallel signal at the output of pin 5 of the microcontroller. I think it's in firmware.Some signal is sent along with the beeper output pin (buzzer). See this vid...

MikeB wrote: ↑Mon Nov 13, 2017 10:16 am I have the fix for that, I'll try to post updated files later today.

Mike.

Ok work now !!!
Only I'm testing this version? I feel alone. Brazil is in crisis, not even thinking about buying a Qx7.
Can I test something specific, Mike?

Thanks Mike !!


Marco.

Thanks Mike,


take your time.

Marco.

Thanks Mike,

And when the countdown is less than zero? It does not say "minus a minute".

Hi Mike, My tests, These on the main processor: PB7- OK input PC0- OK input PC4(LCD_WR)- OK input PC6- OK (for frsky mod)input PC7- OK (for frsky mod)input PG2- OK (for haptic mod) output PG5- OK (2561 only) input The following on the MegaSound module:(whereas internal pull up resistor for input) XP...

Normal....Use original Turnigy 9x? (atmega64) ?

Hi Mike

In "minus one minute" it says "102". "55" and "minutes." So successively in negative minutes. Version V1.139-, V2-pr822, 11/06/2017.
Can you verify the same?

PS: I am now using the parallel version of megasound, for tests.

MikeB wrote: ↑Thu Nov 09, 2017 2:43 pm I have changed the source code in both er9x and ersky9x to fix this. I thought this fix was in er9xV2 (mbtx) that I posted on the 6th Nov 2017.

Mike.

Sorry, in V2 is OK, I had loaded the old firmware.

Mike, Er9x, in my case m2561. This was reported by some other user by PM. Set timer countdown. Radio says " 1 Minutes" instead of "1 minute". Could you please check that when you have time? Thanks João Hi Mike, In V2 too. This "bug" is already two years old and nobody ...

Hi Mike,

Do you know if sometimes when connecting the TX the megasound does not work, and that has to turn it off and on again to work?

Marco,

Now working !!!

Thanks Mike !!!


Marco.

Hi Mike,

I find another bug... mbtx128 ,PB2 does not save after restarting the TX, PB2 does not appear on the keys diagnotic(PB2 back to "NONE").

Tks Mike !!!!

I've re-wired my ELE switch to PB7 in my '2561 running er9xV2, and when I set the ELE switch to use PB7 it all works. Note that LCD-WR is PC4. [Edit: to use this signal you need to remove a resistor from the board] I'll test other signals if necessary, although I have PC6 and PC7 re-wired as the te...

In V2, if you select one of these as the source to convert a switch from a 2-pos to a 3-pos switch, then the pin should be set as an input automatically, and the switch then work as a 3-pos switch. I'll need to open up my '2561 tx in order to test this. I have the ELE switch as a 3-pos switch on it...

Well, you can select them as input on V1.. João Neither in the V1 version does it work, marking L-WR and PB7 as input. It does not appear anywhere in the r820 or r822 firmware, or where you test the switches, only PB1 and PB2. PC0 and PG5 function as 3 positions, scoring in AIL and ELE, but PB7 and...

HI,

I'm testing on my M128, after writing the eeprom, the message "BAD EEPROM" appears. After formatting, my PB1, PB2, PC0 settings do not work. I would like to test PB7 and L-WR as input, they do not work in V1 version. Only PC0 and PG5 (M2561) work.


Marco.

More video...freeze eeprom https://drive.google.com/file/d/0B7lwCf ... sp=sharing

Tested, menu bliking....

see video.. https://drive.google.com/file/d/0B7lwCf ... sp=sharing

Is this the version?

er9xProv822a.zip
15-Jan-2017 23:08
More Multi text added
(977.29 KiB) Downloaded 384 times

The watchdog timing does vary from one processor to another. It is possible the CPU(s) that don't work have a watchdog that is running fast, so are causing a reboot when others don't. Have you tried the special test version I posted on the board that is rebooting? Mike. This all exhausted me enough...

Hello, today I changed the microcontroller to one that I'm sure is working. When I saved a new model, the 47uf capacitor after the 7805L burned (short circuit), also burned regulator 7805L and 6206A. I changed the capacitor and regulators and TX stopped rebooting. I understood nothing !!! Everything...

I already tested two microcontrollers (m2561). With the M64 it worked.
FUSES: Baixo=de Alto=d1 Ext=fc, Argument used -B 1000

Hi Mike ...


I use r821(r820 in radio), ER9x, M2561, I have two radios with the same setup. This one has this problem.
See this video...https://drive.google.com/file/d/0B7lwCf ... sp=sharing

NO MODS ARE CONNECTED!