openrcforums

Calibrate the sticks ?

I think Helle wants the offset parameter to be available in the Inputs section.

Hi,

Can you develop in what way it was easier ?

Thanks

@Kilrah,
Could it be possible to show the bootloader version number in the VERSION screen on the radio ?
It would help to clear some doubts.

Kilrah wrote: To update the bootloader you need to put the downloaded file on the SD card, browse to it on the radio's SD card browser, and select update bootloader.

@g6ejd,
Perhaps you didn't pay attention to the quote above

You're welcome, but I just read that Kilrah had already talked about the sudo thing earlier

@900supersport,

Another thing, I have to type sudo make install.

Steve,
I'm talking about the internal RF module (XJT) firmware of the Taranis, not OpenTX, and anyways, it's better to have the latest module and receiver firmware.

I recommend you make these updates and check if the problem persists.

Hi,

Do you have updated the internal Taranis XJT and the X8R to the last firmware available from FrSky website ?

I would love to see a picture of what is under the wraps of the PCB antennas. IMO whatever it may be it will more than likely be no better than a sleeve dipole. Laws of physics come into play here. :) Here you go : http://fpvlab.com/forums/showthread.php?2814-Antenna-change-on-FrSky-rx&p=319091...

Just compiled companion on linux 64 bit. Works a treat when launched from the lbuild folder. I've run make install but if I try staring companion I get a No such file or directory message as below. brian@brian-SATELLITE-C870D-11X:~$ companion bash: /usr/local/bin/companion: No such file or director...

RUD is the direct stick value and [ix]RUD is the input value as set in the Inputs menu. Ok. I think I've wrapped my mind around this. So RUD will give you no expo and no weights --- just exactly what the rudder stick is reporting. [ix]RUD will give that input with all of the various weights, switch...

RUD is the direct stick value and [ix]RUD is the input value as set in the Inputs menu.

Hi i update to 2.0.0 but now i missing the toggle switch funktion, i start my timer with a logical switch combination, and stop him with the same, but now there is no selection to configure the timer 1 ? can anybody help? Regards Patrick Just use a logical switch with sticky function and use it for...

Hi,

I think there is perhaps a bug somewhere.
I've simplified Zebaloo eepe and reproduced the strange behavior.
It seems to be an interaction between flight modes and mixes delays.
See the eepe below.

I don't have a dog in this fight and probably should keep my big mouth shut -- but it seems to me that using the name FIRMWARE would be wise and also grammatically correct. If there were a variety of different firmware (receivers, sensors, etc) then the plural would be correct, but if all assets in...

LTMNO wrote:.so that means i don't have the latest 2.0 from OpenTX?
does that mean i am not running 2.0 firmware that was just released?

Hi,

Just go to the Radio Setup menu (long press menu) -> page 4/8 Version and you will see what firmware is installed.

Tchao

Ah ok !

Moreover, could the TX simulator in Companion be also translated ?

Many thanks to the dev team for the great work. Bertrand, I just saw a minor fout in the French version: In the general setup of Taranis, it is now possible to define the tones for the vario with 3 new parameters. In Fr, the same text "Tonalité au zéro" is displayed twice (once for the fi...

Great work !!

Thanks everybody !!!

Hi, I have used the settings I described above but I think I also found the problem you had. The image must have 16 colors, no more, no less, after being converted in indexed mode. You can check that with Image/Image properties in the menu. If the image got less than 16 colors, Gimp will adjust the ...

Obviously, I've already used Gimp to make images for OpenTX, and as you can see, it works

Hi,

You can draw and save 4bit images with Gimp:
In the Image menu choose Mode / Indexed... then generate optimum palette with 16 colors and save file in .bmp format with the File/Export... command.
Gimp will automatically save in .bmp 4bit format.

Tchao

Hi,

OpenTX 1.99.7:
In the Input menu, when I set different rates according to flight modes, I can't see the numbers of the corresponding flight modes anymore.

Hi, Thanks for your comments ! At first, I tried a more horizontal layout but I found the successive "label+input field" really difficult to read on the same line, that's why I choose to make some kind of vertical blocks. Indeed, tall panels could be a problem on little screens so why not ...

Hi,

Here is the Model / General Edit panel revisited:

Hi,

No problem here to compile with Ubuntu 64bit.
I've followed these instructions to install the ARM toolchain : https://launchpad.net/~terry.guo/+archi ... m-embedded

@adilsongoliveira,
I'm doing exactly what is explained in the wiki to build Companion and it works.

Tchao

Thanks Bertrand !

I'd like to do that but I'm afraid not having the skills... I've just played with QT Creator.

Perhaps with some (lot) help.

And I have other ideas for the UI but it will take me more time to show.

Tchao

Hi, I didn't like the UI look on my XP machine so I've been trying some graphical ideas with QT Style Sheets and I think it could be interesting. The look is pretty close between different operating systems as you can see with the Input Edit window in the image attached. I'd like to know what you th...

Bin size varies (considerably) with the version and even build/system of compiler used, take a look at this comment https://github.com/opentx/opentx/pull/830#issuecomment-38349682 Yes, I knew that the build size could be different depending on the compiler, that's why I wanted to make a direct comp...