openrcforums

Yes it is RxBt in the telemetry menu.
you don't have to add a sensor, its part of the system Tx/Rx system.

Hi

OK I found the problem.
I downloaded the config program V1.1 and there is a V1.3.
It works now with V1.3.
Not sure how I obtained the old V1.1

Hi, I'm trying to configure and calibrate my S6R using the STK USB I just bought. All seems to be working well until I do the WRITE after the calibration in the config program. I receive this message from the config program S6R V1.1: S6R config has stopped working, program will closes and reopens wi...

Good to know.
Thanks

Hi, In the Taranis OpenTx V2.1.9 telemetry menu, these is the "discover new sensors". I have already done this and got and edited many sensors. The edit part is important for my question. If I add a new sensor and do another "discover new sensors", will this action erase all my e...

No need for ersky9r.
I can take V2.2.0 RC8, then calibrate S6R and come back to V2.1.9 until V2.2.0 is officially released.
But: I will use the PC instead, simpler. Now I need to buy the STK USB adapter.

Thanks to all for your answers.

Hi,

you think my next question is when the V2.2 will be released? right?
Well, no, I will be patient and wait for it.

So if I summarize, if I don't use the PC to configure I cannot use the S6R with V2.1.9. Right?
Will V2.2.0 RC8 work?

Thanks for all the answers.

Thanks Helle, So what you are describing is that I need to use the PC to configure the S6R and then I can use V2.1.9 to do this: With V2.19 you can do this: Setting at Tx Mode D16 Ch 1-16 Ch10, Ch11 setting the 4 main Function of the S6R manual, auto, ...., .... Ch12 starts selftest (Starts with 3ti...

Hi,

Can anyone confirm if we can use the FrSky S6R receiver with the standard Taranis, not Taranis plus?
And also does it need OpenTX V2.2 and higher to work? Will V2.1.9 work?

Thanks

Great, thanks Kilrah.

Kilrah, Is this what you meant: Instead of defining the four sensors C1,C2,C3,C4, I should define only one sensor and name it let's say lowcel by putting the lowest instead of index 1,2,3,4. Then simply do this: L1 a<x lowcel 3.4 L1 play track "low battery" ? Is that it? Thanks, Ray

Thanks Kilrah,

So I set my four cells at lowest, but how do I set the play track "low battery" to detect the first lipo individual cell to be lower than 3.4 volts?

thanks
Ray

Hi all, I made a program to monitor individual Lipo cells (a 4S LiPo pack) and play track "low battery" if any of the 4 cells gets lower than 3.4 volts. My LiPo sensor (FrSky FLVSS) individual cells are identified as follows: C1,C2,C3,C4. Below is my program. Please advise if there is an e...

Thank you jtaylor.

Ray

Hi, I have a few questions: 1- In the Radio setup what does play delay (sw.mid pos) do? Mine is set at 150ms. 2- Can we use real numbers such as 3.4 to set global variables? or is it just only integers? 3- In the model menu, what does the tick or check on global variables do? It enables or disables ...

Hi,

Yes of course, not with the receiver,this is the switch I was talking about (-100% and +100%).

Ray

Hi, This should be pretty easy to do and can be done in the special functions menu only. You must first record and store the two sound tracks for "led ON" and "LEd off". Then store them in the SD card directory sound. You will need a switch that will operate the same as a PPM ser...

Correct,

I got the link from Kilrah.
I looked at the 3 PDF and they look great. Explains a lot of things.

Thanks again Kilrah.

You guys are doing a great job.

Ray

Thanks Jhsa.

There is one I just found that was made I believe by a French guy that looks great in 3 separate PDF files.
The PDF are in English.

Ray

Thanks Jhsa,

It would be good to have a signal flowchart of OpenTx, with flight modes,inputs, trims, mixer, outputs etc etc.
I have seen one once in one of the manuals but I can't find this manual anymore.
At that time I did not realize that was precious info.

Ray

Hi Kilrah,

OK thanks, that explains it. I will change it for all models.
So what you are stating is that it is not recommended to place the rates in the mixer.
Thanks for your patience

Ray

Kilrah, A quick way to see the trim problems as you requested: Use companion, load my eepe file and click on the SA- switch in the simulator to change from flight mode 0 to flight mode 1. When switching flight modes, you will see in the simulator some joystick movements; the trims move and they are ...

Kilrah,

Attached is one of my eepe files.

Please look at the Model # 1 the FourStar40 for the trim problem in flight mode 0.
Look at the Extra-300 for how I solved my trim problem (not using flight mode 0).

thanks
Ray

Hi Kilrah, When I set (adjust while flying) my trims when flight mode 1 is selected and want to apply them (keep them) in flight mode 2 and 3, it works. It works for me means I can keep the same trims in flight modes 1,2 and 3 that were set in flight mode 1. If I choose flight mode 0 as my official ...

Hi Kilrah, The trims (RETA) adjusted in the default flight mode 0 works fine when flight mode 0 is selected. However, if you select flight mode 1 and you have programmed trims from flight mode 0 trims in the flight mode 1 it does not work for sure. The way I solved my problem is not use flight mode ...

Hi Kilrah,

Can you confirm about trims in Flight mode 0 are not applied in other flight modes (1 to 8)? For V2.1.9

Thanks
Ray

Have you tried the search engine of Digi-key?

Hi Kilrah,

You're right I should have used the term applied instead of preserved.

So: when I want flight mode 0 trims applied in flight modes 1 or 2 or 3.... up to 8, it does not work.
Flight modes 1 to 8 do not apply the trims of flight mode 0, otherwise it works.

Ray

Hi,

Can anyone confirm or contradict the fact that using flight mode 0 trims in other flight modes (1 to 8) are not preserved?
Flight mode 0 trims are not preserved but all other flight modes (1 to 8) trims when used in other flight modes (1 to 8), they are preserved.

Thanks