Search found 754 matches

by kalle123
Wed May 03, 2017 10:47 am
Forum: General help (FrSky Taranis radio)
Topic: New here...dont see Qx7 board,but need help.
Replies: 14
Views: 2285

Re: New here...dont see Qx7 board,but need help.

Also why does my QX7 not have the failsafe setting in setup menu 2/12? First of all. That is a lousy video, you mentioned. Second, read, what Kilrah mentioned in his post. "Remote failsafe setting is only available for X receivers (D16 mode). D receivers (D8 mode) need to have failsafe configured w...
by kalle123
Sat Apr 29, 2017 5:58 pm
Forum: General help (FrSky Taranis radio)
Topic: Companion 2.2 build options
Replies: 8
Views: 2010

Re: Companion 2.2 build options

Here is the link. It is on the open Tx site. http://openrcforums.com/forum/download/file.php?id=14082 page 14 Now I know, what you were looking for ... First thought, you were looking for that here https://github.com/opentx/opentx/wiki/OpenTX-Compilation-Options And that list on page 14 is by far N...
by kalle123
Sat Apr 29, 2017 10:28 am
Forum: General help (FrSky Taranis radio)
Topic: Companion 2.2 build options
Replies: 8
Views: 2010

Re: Companion 2.2 crashes

Raythegreat wrote:
Sat Apr 29, 2017 2:17 am
OK I found the document that explains companion's 2.2 build options.
Would you share the link, please.

br KH
by kalle123
Sun Apr 23, 2017 10:53 am
Forum: Hardware
Topic: [FIXED!] XJT beeping
Replies: 58
Views: 9832

Re: XJT beeping

Would try to invert RX TX on FTDI with FT_prog.
by kalle123
Sat Apr 22, 2017 5:02 pm
Forum: OpenXVario - an open source vario supported by the open source firmwares!!
Topic: New beta version of openXsensor (=openXvario)
Replies: 482
Views: 64222

Re: New beta version of openXsensor (=openXvario)

Code: Select all

#define USE_INTERNAL_REFERENCE  // uncomment this line if you use 1.1 volt internal reference instead of Vcc
Why this line in uncommented? That means, you are measuring arduino input on ....

Just see, that mstrens was faster ;)
by kalle123
Fri Apr 21, 2017 9:34 am
Forum: FrSky Taranis radio
Topic: tranis x9d NOTplus
Replies: 8
Views: 1569

Re: tranis x9d NOTplus

lanerover wrote:
Fri Apr 21, 2017 9:20 am
kalle is 2.19 likely to make that much difference from 2.017?
Think, it is worth to give it a try ;)
by kalle123
Thu Apr 20, 2017 3:55 pm
Forum: OpenXVario - an open source vario supported by the open source firmwares!!
Topic: GPS sensor
Replies: 418
Views: 57958

Re: GPS sensor

oXs GPS under MPX M-Link with FrSky converter on Taranis. Tested today. Working fine. oXs #1 with MS5611, ACS712 and voltage divider for Lipo voltage oXs #2 for ublox Neo7M See some pics here -> http://www.rc-network.de/forum/showthread.php/567929-OpenTX-Multiplex-MLINK-Konverter?p=4309441&viewfull=...
by kalle123
Wed Apr 19, 2017 9:09 am
Forum: FrSky Taranis radio
Topic: tranis x9d NOTplus
Replies: 8
Views: 1569

Re: tranis x9d NOTplus

lanerover wrote:
Wed Apr 19, 2017 7:05 am
Guess there's no answer to this one, looks like I'll be reflashing back to pre 2.00 version ...
A bit obsolete. ;)

Why not put the actual version (2.1.9) on your tx and try this?

http://www.open-tx.org/downloads.html

br
by kalle123
Mon Apr 03, 2017 5:40 am
Forum: openTx
Topic: Temporarily save telemetry value (while in flight)?
Replies: 12
Views: 1561

Re: Temporarily save telemetry value (while in flight)?

Is this something that can be achieved with OpenTX? Mike, that was andrewjus question. ;) Hope, he can post post results of his test. At the moment, I only know, that you can bring a telemetry value like Alt into the system. But I did not do any tests with that. Was puzzled to see a new line "scale...
by kalle123
Sun Apr 02, 2017 5:55 pm
Forum: openTx
Topic: Temporarily save telemetry value (while in flight)?
Replies: 12
Views: 1561

Re: Temporarily save telemetry value (while in flight)?

Should be possible.

Maybe andrewju tells us after testing ....
6.jpg
by kalle123
Sun Apr 02, 2017 3:21 pm
Forum: openTx
Topic: Temporarily save telemetry value (while in flight)?
Replies: 12
Views: 1561

Re: Temporarily save telemetry value (while in flight)?

@andrewju.

But could be limited, as GVx max value is 1024 and Alt is in 1/10 m. :cry:
by kalle123
Sun Apr 02, 2017 1:18 pm
Forum: openTx
Topic: Temporarily save telemetry value (while in flight)?
Replies: 12
Views: 1561

Re: Temporarily save telemetry value (while in flight)?

andrewju wrote:
Sun Apr 02, 2017 10:32 am
It's not the maximum (or minimum) height, it's some other point he will choose himself.
He is not looking for a max min value.
by kalle123
Sun Apr 02, 2017 11:53 am
Forum: openTx
Topic: Temporarily save telemetry value (while in flight)?
Replies: 12
Views: 1561

Re: Temporarily save telemetry value (while in flight)?

Only a suggestion

Make a new INPUT with ALT (height). Besides stick inputs etc.

Make for instance,a new SPECIAL FUNCTION with SWITCH, ACTION (Adjust GVx), SOURCE (your new INPUT)

Now you should have the value ALT stored on GVx.

Hope, this helps ...

br
by kalle123
Sat Apr 01, 2017 3:37 pm
Forum: OpenXVario - an open source vario supported by the open source firmwares!!
Topic: Brainstorm: oXs as wing level indication system
Replies: 27
Views: 4617

Re: Brainstorm: oXs as wing level indication system

Just did a short test here, works, no problem ;)

IMG_20170401_172619.jpg
1.jpg

Did you

- un-commet this line? #define USE_6050 // uncomment this line if a IMU 6050 is connected

- connect INT? Interrupt from 6050 has to be connected to Arduino pin 2 or pin 3
by kalle123
Fri Mar 31, 2017 2:05 pm
Forum: openTx
Topic: Easy way to switch-off RF module at startup
Replies: 14
Views: 2977

Re: Easy way to switch-off RF module at startup

Seen this subject here:

"Easy way to switch-off RF module at startup"

Loaded the video and what do I see? FUTABA :roll:
by kalle123
Wed Mar 22, 2017 6:30 pm
Forum: openTx for FrSky radios
Topic: Unable to flash firmware (More than one DFU device found)
Replies: 6
Views: 3191

Re: Unable to flash firmware (More than one DFU device found)

thatsnailguy wrote:
Wed Mar 22, 2017 1:54 pm
More than one DFU capable USB device found, you might try `--list' and then disconnect all but one device
... and did you try that?
by kalle123
Sat Mar 18, 2017 6:35 am
Forum: Hardware
Topic: Dead Taranis...not the plus
Replies: 23
Views: 3375

Re: Dead Taranis...not the plus

Sean295 wrote:
Sat Mar 18, 2017 3:38 am
But my pc does not see the SDcard when it is in the taranis....
Take the SDcard out of your Taranis. :lol:
by kalle123
Sun Mar 12, 2017 2:13 pm
Forum: FRSky Horus radio
Topic: At last
Replies: 10
Views: 3137

Re: At last

Gps.wav, on.wav and off.wav were there, just merged the wav files. ... Simple 8-)

KH
by kalle123
Sun Mar 12, 2017 1:00 pm
Forum: FRSky Horus radio
Topic: At last
Replies: 10
Views: 3137

Re: At last

I guess not. Amber has much better quality. Shame that is a dead pack. Can't be updated with the same voice? For me would be kind of useless as I don't like to use different voices. OK. For me amber is fine. Specially with maiden flights. That voice gets my blood pressure down :mrgreen: And amber i...
by kalle123
Sun Mar 12, 2017 11:19 am
Forum: FRSky Horus radio
Topic: At last
Replies: 10
Views: 3137

Re: At last

jhsa wrote:
Sun Mar 12, 2017 1:44 am
Another thing I didn't like was the quality of the voice files, at least the ones I've heard..
It was not amber sound pack, for sure ... ;)

KH
by kalle123
Fri Mar 10, 2017 3:03 pm
Forum: FRSky Horus radio
Topic: can't flash my Horus X12
Replies: 3
Views: 1537

Re: can't flash my Horus X12

Peter, if you are familiar with the German language, maybe take Helles Handbuch at hand and follow the instructions you find there.

It is very comprehensive.

Find it here -> viewtopic.php?f=92&t=3563&p=118175&hili ... ch#p118175

br KH
by kalle123
Tue Mar 07, 2017 2:16 pm
Forum: Hardware
Topic: XJT module beeps and not working
Replies: 5
Views: 1082

Re: XJT module beeps and not working

I guess, you don't have a second module at hand, just to see, if the issue comes from the TH9X or from the XJT module?

Or can you check with a friends transmitter?

br
by kalle123
Tue Mar 07, 2017 11:22 am
Forum: General Information & Rules
Topic: Issue login
Replies: 13
Views: 14421

Re: Issue login

lancaster wrote:
Tue Mar 07, 2017 10:57 am
Hi Guys
I had the same error message yesterday but it seems to working without a problem today
regards
Hans
So I was not the only one ;)
by kalle123
Tue Mar 07, 2017 10:20 am
Forum: General Information & Rules
Topic: Issue login
Replies: 13
Views: 14421

Re: Issue login

João, I don't care for that DDoS attack protection, I was totally cut off! Getting a bit nervous :mrgreen:

But as I saw that folder structure "/var/www/html/", I knew, it was not on my side. Don't have that folders here ....
by kalle123
Tue Mar 07, 2017 9:05 am
Forum: General Information & Rules
Topic: Issue login
Replies: 13
Views: 14421

Issue login

Had an issue with login into the forum. Message was "Catchable fatal error: Argument 1 passed to phpbb\notification\type\base::__construct() must implement interface phpbb\db\driver\driver_interface, instance of phpbb\user_loader given, called in /var/www/html/openrcforums.com/forum/cache/production...
by kalle123
Tue Mar 07, 2017 8:48 am
Forum: openTx
Topic: otx file extension
Replies: 3
Views: 1107

Re: otx file extension

Thank you! ;)
by kalle123
Tue Mar 07, 2017 8:19 am
Forum: openTx
Topic: otx file extension
Replies: 3
Views: 1107

otx file extension

Found that statement here "new .otx file format for the Horus"

http://rcdiy.ca/opentx-2-2-whats-new/

But what is behind that otx file format? ONLY for Horus or what?

br
by kalle123
Fri Feb 17, 2017 6:10 pm
Forum: OpenXVario - an open source vario supported by the open source firmwares!!
Topic: GPS sensor
Replies: 418
Views: 57958

Re: GPS sensor

RightRudder wrote:Expensive today, but in time the price will drop.
Searched for those GPS modules and saw some prices ... :roll:

Think, we are not in a hurry.
by kalle123
Sat Feb 11, 2017 7:14 am
Forum: General help (FrSky Taranis radio)
Topic: New FrSkyhas a funky smell when first turned on is this normal?
Replies: 6
Views: 847

Re: New FrSkyhas a funky smell when first turned on is this normal?

1. Remove the battery from the battery bay and have a look inside.

2. A good reason to get yourself a digital voltage meter. Comes handy.

Go to advanced search