Search found 553 matches

by KAL
Sun Jan 10, 2016 7:39 pm
Forum: ersky9xr
Topic: Model Setup Help?
Replies: 45
Views: 10973

Re: Model Setup Help?

I had a look at 'kaos-nano (PPM).eepm'. Did you realize, that throttle (ch1) is at least 50% open (with ID0, even higher with ID1 and ID2) as long as throttle cut is disabled? Therefore I suppose you did bind with throttle cut enabled (ch1 at 0%)? (throttle channel has to be at 0% for arming) Maybe ...
by KAL
Sun Jan 10, 2016 9:14 am
Forum: Template Library
Topic: Blade Nano CP S
Replies: 22
Views: 14918

Re: Blade Nano CP S

Hi, I don't have a model file for the nano CP S but for the basics here my model file for nano CP X: nano CPX.eepm Note: NO handling for panic mode as the X doesn't have this feature ID2 = Idle Up, ID0 and ID1 = stunt mode limits on CH6 are set to avoid too much pitch (have to be set individually fo...
by KAL
Sat Jan 09, 2016 6:42 pm
Forum: er9x
Topic: Eeprom issue while trim
Replies: 8
Views: 1701

Re: Eeprom issue while trim

Have you seen this post?
If you are familiar with soldering iron and xacto knife then this mod should be no big problem.
And it's worth the effort 'cause a reboot during flight is NOT a 'must have'!

Klaus
by KAL
Sat Jan 09, 2016 12:18 am
Forum: erskyTx (was ersky9x)
Topic: ERSKYTx (was ersky9x) Questions
Replies: 1965
Views: 269839

Re: ERSKY9x Questions

Why not changing only the label?
by KAL
Fri Jan 08, 2016 5:18 pm
Forum: erskyTx (was ersky9x)
Topic: ERSKY9X Coding
Replies: 4475
Views: 375766

Re: ERSKY9X Coding

- save/restore single models to SDcard
- save/restore eeprom to SDcard (in development yet)

Klaus
by KAL
Fri Jan 08, 2016 4:16 pm
Forum: 9Xtreme upgrade board
Topic: Question concerning POT4 and POT5
Replies: 2
Views: 639

Re: Question concerning POT4 and POT5

Thank you for enlighting this mystery :D
by KAL
Fri Jan 08, 2016 3:59 pm
Forum: 9Xtreme upgrade board
Topic: Question concerning POT4 and POT5
Replies: 2
Views: 639

Question concerning POT4 and POT5

I think about adding sliders to my 9Xtreme so I stumbled over this: In hardware menu the options for POT4 and POT5 are EXT1 to EXT4. Am I right that EXT1 to EXT4 for the pots are the 4 inputs formerly for the gimbals whereas EXT1 to EXT8 for the switches/push buttons are the 8 inputs formerly for th...
by KAL
Fri Jan 08, 2016 3:47 pm
Forum: 9Xtreme upgrade board
Topic: Changement de carte mère surTGYX
Replies: 10
Views: 2075

Re: Changement de carte mère surTGYX

As far as I know the 9Xtreme board tests at every power on
whether the slave firmware is present (on the 9X board) or not.
If not, it (the 9Xtreme board) flashes the 9X board with the required firmware.

Klaus
by KAL
Fri Jan 08, 2016 3:41 pm
Forum: erskyTx (was ersky9x)
Topic: ERSKYTx (was ersky9x) Questions
Replies: 1965
Views: 269839

Re: ERSKY9x Questions

Just had a look at eePe a few seconds ago and it's the same ...
ER9X i cannot test 'cause I have no radio at hand at the moment.
by KAL
Fri Jan 08, 2016 3:20 pm
Forum: erskyTx (was ersky9x)
Topic: ERSKYTx (was ersky9x) Questions
Replies: 1965
Views: 269839

Re: ERSKY9x Questions

For those things it would be nice if we could reduce simulation speed (e.g. by 1/2,1/5,1/10,...) in eePskye, wouldn't it? (Or is it possible and I missed it?) What puzzled me a bit is the fact that to delay the activation of a switch (in the mixer) we need to set the down delay. I had expected to us...
by KAL
Fri Jan 08, 2016 11:57 am
Forum: erskyTx (was ersky9x)
Topic: ERSKYTx (was ersky9x) Questions
Replies: 1965
Views: 269839

Re: ERSKY9x Questions

Maybe the following can work:
switches.jpg
mixes.jpg
Note: the duration of the 1-shot at L4 and L5 must be longer than the delay for CH6 in the mixer.
If not, CH6 doesn't send a pulse to activate agility mode.

I cannot test it myself, 'cause one motor of my nano QX is suffering ...

Klaus
by KAL
Fri Jan 08, 2016 11:30 am
Forum: 9Xtreme upgrade board
Topic: eepskye editor and the eepe editor
Replies: 9
Views: 1800

Re: eepskye editor and the eepe editor

I don't know about OpenTX and CompanionTX. With eePe and eePskye it isn't possible to drag and drop mix lines but it should be possible to copy whole models from eePe to eePskye. I tried this a few minutes ago, but eePe crashed while dragging. as a workaround use copy and paste in the 'file' menu. Y...
by KAL
Fri Jan 08, 2016 9:20 am
Forum: erskyTx (was ersky9x)
Topic: ERSKYTx (was ersky9x) Questions
Replies: 1965
Views: 269839

Re: ERSKY9x Questions

I think of two possibilities: it's just as João posted: The nano QX changes into full agility mode only when the sticks are (nearly) centered... This can be solved by forcing ch2 and ch3 to 0% for a short moment before activating agility Change to agility mode is suppressed as long as a movement is ...
by KAL
Thu Jan 07, 2016 6:10 pm
Forum: erskyTx (was ersky9x)
Topic: ERSKYTx (was ersky9x) Questions
Replies: 1965
Views: 269839

Re: ERSKY9x Questions

Does the nano QX change its color from blue to red when you try to flip?
by KAL
Thu Jan 07, 2016 5:45 pm
Forum: erskyTx (was ersky9x)
Topic: ERSKYTx (was ersky9x) Questions
Replies: 1965
Views: 269839

Re: ERSKY9x Questions

mcometa wrote:And so I tested it...
João's or my version?
mcometa wrote: ...and the quad does nothing...
what means nothing? No reaction at all or just slipping away in the pointed direction?

Klaus
by KAL
Thu Jan 07, 2016 5:35 pm
Forum: erskyTx (was ersky9x)
Topic: ERSKYTx (was ersky9x) Questions
Replies: 1965
Views: 269839

Re: ERSKY9x Questions

jhsa wrote: bool.. what?? What's that? :o :? ...
Boolean algebra is the algebra of AND, OR, XOR ... in conjunction with binary numbers ...
For further questions ask Mr. George Bool :mrgreen: :lol:
by KAL
Thu Jan 07, 2016 5:08 pm
Forum: erskyTx (was ersky9x)
Topic: ERSKYTx (was ersky9x) Questions
Replies: 1965
Views: 269839

Re: ERSKY9x Questions

(N.B. There should be a reset/clear all menu somewhere in the Logical Switches page. When you have all the values up and you can't figure out and just want to reset do it all over again you wanna hit this "ahhhhh s***!" button. Also a copy/move is helpful :D) Yeah, I think I suggested that a while ...
by KAL
Thu Jan 07, 2016 5:03 pm
Forum: erskyTx (was ersky9x)
Topic: ERSKYTx (was ersky9x) Questions
Replies: 1965
Views: 269839

Re: ERSKY9x Questions

jhsa wrote:Klaus, a simplified version of your idea.. ;) Save a couple logical switches ...
Yeah, that's true.

Sometimes I hardly struggle with this boolean algebra... :) ;)

Klaus
by KAL
Thu Jan 07, 2016 4:44 pm
Forum: erskyTx (was ersky9x)
Topic: ERSKYTx (was ersky9x) Questions
Replies: 1965
Views: 269839

Re: ERSKY9x Questions

Tested it (my solution) on the bench with my Nano QX and worked OK so far (no flight test!!!).
But to be able to change stabilty mode manually (with trainer switch) I would recommend to add
+R 100%Full Switch(TRN)
to channel 6 ...
mixes.jpg
mixes.jpg (22.39 KiB) Viewed 2286 times
Note the replace option!

Klaus
by KAL
Thu Jan 07, 2016 4:19 pm
Forum: erskyTx (was ersky9x)
Topic: ERSKYTx (was ersky9x) Questions
Replies: 1965
Views: 269839

Re: ERSKY9x Questions

And don't forget: 100% spektrum equals to 80% erSKY9x.
So the limits should be set to +/- 80 except throttle low (for arming):
limits.jpg
Klaus
by KAL
Thu Jan 07, 2016 4:08 pm
Forum: erskyTx (was ersky9x)
Topic: ERSKYTx (was ersky9x) Questions
Replies: 1965
Views: 269839

Re: ERSKY9x Questions

I'm not very familiar with all this new switch options but here is what I would try: Nano.jpg L1 is active when |ail| > 98 L2 gives a peak of 0.2 sec when L1 goes active L3 gives a peak of 0.2 sec when L1 goes inactive L4 combines L2 and L3 Same with L5 to L9 but ele LB combines L4 and L9 So use LB ...
by KAL
Thu Jan 07, 2016 3:29 pm
Forum: erskyTx (was ersky9x)
Topic: ERSKYTx (was ersky9x) Questions
Replies: 1965
Views: 269839

Re: ERSKY9x Questions

As far as I understand he needs a low-high-low transition when the stick value reaches a threshold
to activate agility mode (and make e.g. a flip possible)
and another low-high-low transition when stick value then gets lower than the threshold
to enter stability mode

Klaus
by KAL
Thu Jan 07, 2016 3:12 pm
Forum: erskyTx (was ersky9x)
Topic: ERSKYTx (was ersky9x) Questions
Replies: 1965
Views: 269839

Re: ERSKY9x Questions

Hi João,

a problem would be that the Nano QX is switched between 'agility' and 'stable'
by a toggle (momentary) switch (e.g. the trainer switch) on Channel 6.

And therefore if the Nano QX misses a switch transition he will get into trouble ...

Klaus
by KAL
Tue Jan 05, 2016 7:36 pm
Forum: eepSKYe
Topic: eepSKYe
Replies: 705
Views: 116981

Re: eepSKYe

Hi Mike, I never used the print function but the posts of 'gerhardp' in "er9x development" about print function in eepe made me curious. So I tried it with eepskye. I found that using this function causes eepSKYe to crash when sticky throttle cut (safety switch type 'X') of the selected model slot i...
by KAL
Tue Jan 05, 2016 6:23 pm
Forum: Hardware
Topic: No Power: Flashing success turns to burned out brick failure
Replies: 47
Views: 4644

Re: No Power: Flashing success turns to burned out brick failure

Same with me.
Worst thing: discard someting that's not used for veeeerrrryyy long, ... ... ... ... then you will need it a few days later ... ;) (lex murphy)
by KAL
Tue Jan 05, 2016 6:12 pm
Forum: Hardware
Topic: No Power: Flashing success turns to burned out brick failure
Replies: 47
Views: 4644

Re: No Power: Flashing success turns to burned out brick failure

That's one secret of a good hobbyist: use ev'rything you get your hands on (of course it must be suitable ;) ) :D 8-)
by KAL
Tue Jan 05, 2016 5:22 pm
Forum: Hardware
Topic: No Power: Flashing success turns to burned out brick failure
Replies: 47
Views: 4644

Re: No Power: Flashing success turns to burned out brick failure

Simply put together a shashlik skewer, shashlik skewer.jpg a needle, needles.jpg a piece of wire and shrinking tube (maybe some CA glue, too) and you have an excelent probe for smd parts. Things you probably find in most households... (Don't try to solder the wire to the needle, in most cases that's...
by KAL
Sun Jan 03, 2016 3:51 pm
Forum: er9x
Topic: No joy with 9x transmitter and SmartieParts SP Basic firmware programmer for Er9x install
Replies: 80
Views: 10032

Re: No joy with 9x transmitter and SmartieParts SP Basic firmware programmer for Er9x install

jhsa wrote:... Quite expensive though ...
Divided by the years I have this pen I think much more went down the toilet for this hobby :mrgreen: :lol:

Klaus
by KAL
Sun Jan 03, 2016 1:57 pm
Forum: er9x
Topic: No joy with 9x transmitter and SmartieParts SP Basic firmware programmer for Er9x install
Replies: 80
Views: 10032

Re: No joy with 9x transmitter and SmartieParts SP Basic firmware programmer for Er9x install

Hi João,

this pen is called "Glasfaser-Radierer".
You can get it e.g. at amazon or ebay.

Klaus

Go to advanced search