openrcforums

OK, Thanks.

No worries, when I receive it I will try do something and you can test the code withing vario to aprove using the Arduino code. So for ID should I use the GPS_SPEED_A 0x19, or we can add specific IF forAir Speed to The System?

Is it somebody working on this add or not? I ordered Air Speed Sensor from Eagle Trees Systems (It will take few days to receive it) and I will try to implement it to the Arduino Vario. But if somebody is working on it, just let me to know. Also is there any specific/preferred ID address in the Frsk...

I found the thread. Thanks

Yes I mean Eagletree Airspeed sensor and telemetry from Frsky. I was looking for the thread, probably I missed it. Going check again. Thanks.

Is it possible or maybe its already implemented to use this Air Speed Sensor from Eagle to monitor airplane speed and have also possibility to set alarm based on the speed? Or is there any other method (use gps) for monitoring speed? Actually gps will not work as I need to know Air Speed and gps is ...

At the Toledo show Yesterday I got hands on it. Feels nice , price should be $175 for the radio and the Aluminum Case. And they are nice people. End of April supposed be available with new ball bearings sticks. Also there is possibility use those new sticks in Turnigy 9X. Nice. Sbus Smart port. New ...

Yes I have Sky9X board, I will test it. Thanks

Thank you very much. I will test it.

No I meant if you have range from -100% to 100% for throttle travel I meant increase from -100% add 15% to the -85% so range will be -85% to the +100% or if you using range from 0-100% that mean instead 0% goes to the 15% and range will be 15% to the 100%. This is for B25 two engine Model with smoke...

I have question: Is it possible to do following with Open9X: It is for two electric motors with two ESC separate channels When I turn switch 1 ON it will increase Throttle 1 to 15% but keeping throttle 2 down to -100% but after for example 20 seconds it will increase Throttle 2 also 15% and after bo...

Thank you.

For some reason my companion9x saying that I have last firmware downloaded and marked r1947. But last release on this forums is r20xx.
So is it problem with companion or I have to download source and compile for myself? Is it 1947 last stable official release for the public?

Does anybody has the PCB v2 from upgrading Turnigy 9X for sale within Canada?

I switch the wire to the PPM pin, works good (binding no problem) but not message on the screen. Maybe we do not need it, I was just assuming that there is a message on the screen while binding. That's all. Thanks for help everybody.

Thanks, I'll do it that way than. Yes there is serial signal on the PPM pin and its 3.3V p-p, but why is not the Binding message on the screen when I'll try to bind (Power Up + Trainer switch holding)?

Hello again, so on SKy9X is not implemented DSM2 on the serial port or is it? I'm confused now. Or if I will compile source and pick upSky9X and DSM=SERIAL it will work? I updated to svn 1678 for Sky9X but I still do not have any info about binding on the LCD when I'm holding Trainer Switch with Pow...

I found out that I do not have on com port 1 serial data for DSM2 module. Have to look deeper where they are, or what settings I need. Going upgrade to recent version and I'll see

Ok I thought that its suppose to show something. Thanks. Im at the field so I will investigate when I will be back home. Skiing with tha yak54 on the snowy runway

Yep, no warnings, no splash. Just won't show binding and actually it is not binding. I just swaping modules frsky and dsm2 both works with serial adjusted to 3.3v as I did remove rs232 converter so just swaping modules without any external wires. Probably I have wrong firmware open 9x 1563.

Probably I missed something but I'm using Dsm2 serial module for BNF microairplanes. Today I did try to bind new model. I setup model and choose the DSM2 proto and LP4. Turn off radio , hold trainer switch and turn radio on while holding trainer switch(on the display itshows ID0 on) but no Binding o...

Thank you.

Is it X9D on the market already, or we are talking about future release? X12D would be awesome to have also

Thank you Romolo, that one works as it suppose. Thank you for hard work.

I did try to compile, but showing still some errors, so some bad setup under Win7. Do not worry about that just for future refernces. I will work on the compiling later or you can send it to me by email compiled version. Or PM me link to download manually. Thanks for hard and fast work.

Thank you, great news.

Actually both, SD backups and also beackup from radio, I'll try upload one from yesterday

The problem is that only file from backup I can read is the one from gruvin9X. All other *.bin backups companion saying Invalid EEPROM File. So I cannot get the System settings for ER9X(ARM) only for Gruvin9X. I just saying that I cannot open any ARM backUp *.bin or *.eepe file, that why I'm not hap...

Thank you. That's worked for models but not for system and calibration menu. But its less job as put all the models in. Thanks.

I have the Companion9X 1.07 build 1532 . I updated Companion and also Companion9X downloaded new FW for Sky9X. I went to reflash my radio, also I marked BackUp and restore EEPROM context. Everything went smoot, but when I powered Up radio it showed screen converting EEPROM and only Model Names staye...