Search found 216 matches

by hageha
Thu Feb 18, 2016 8:30 pm
Forum: OpenXVario - an open source vario supported by the open source firmwares!!
Topic: Releases, Documentation ??
Replies: 10
Views: 2358

Re: Releases, Documentation ??

In order to assess the quality of the GPS signal, it may be important to indicate the number of the satellite. Somewhere that was taken over Tmp1 or Tmp2. e.g. See 8 satellites and Fix 3 for "83". It can be seen earlier if everything is in order. That was here: https://github.com/SamuelBrucksch/diy-...
by hageha
Thu Feb 18, 2016 3:49 pm
Forum: OpenXVario - an open source vario supported by the open source firmwares!!
Topic: Releases, Documentation ??
Replies: 10
Views: 2358

Re: Releases, Documentation ??

After I did some experiments with the OpenXsensor-GPS and my antennas Tracker today, I noticed that SAT's and Fix is not displayed.
Did I do something wrong?
by hageha
Tue Feb 09, 2016 7:16 pm
Forum: OpenXVario - an open source vario supported by the open source firmwares!!
Topic: Releases, Documentation ??
Replies: 10
Views: 2358

Re: Releases, Documentation ??

Looks good ! 166 m but at the time no good fix
by hageha
Tue Feb 09, 2016 5:40 pm
Forum: OpenXVario - an open source vario supported by the open source firmwares!!
Topic: Releases, Documentation ??
Replies: 10
Views: 2358

Re: Releases, Documentation ??

I now flashed the 5 hours old FW.
Galt is still about 29 m (-29 m), but now Hdg appears.
Despite km h setting in config.h, kts displayed.
by hageha
Tue Feb 09, 2016 12:32 pm
Forum: OpenXVario - an open source vario supported by the open source firmwares!!
Topic: Releases, Documentation ??
Replies: 10
Views: 2358

Re: Releases, Documentation ??

Hi, yesterday I built an openXsensor with GPS. Altitude, VSPD, and VFAs are o.k. Gps Lon, Lat also o.k. Galt shows either about 30m or jumps to about -30m. The real height is about 155m. Other GPS values are not shown. I use a Taranis Plus FW 2.17 with a D-receiver I have tried two different Ublox N...
by hageha
Thu Oct 23, 2014 9:55 am
Forum: OpenXVario - an open source vario supported by the open source firmwares!!
Topic: OpenXSensor SPORT Interface
Replies: 522
Views: 73830

Re: OpenXSensor SPORT Interface

T1 , VOLT1 , 1 , 1 , 0 With T1 show both receivers 125 instead of 12.5 If I use: T1 , VOLT1 , 1 , 10 , 0 The display is 12 instead of 12.5 But the speech is "degree" instead of volts! The telemetry settings on the Taranis are identical for both receivers! Unfortunately I only have little knowledge o...
by hageha
Wed Oct 22, 2014 7:56 pm
Forum: OpenXVario - an open source vario supported by the open source firmwares!!
Topic: OpenXSensor SPORT Interface
Replies: 522
Views: 73830

Re: OpenXSensor SPORT Interface

@mstrens
with the changed line everything works on "X" receiver!
With a "D" receiver, the voltage is 10 times greater than indicated.
125 instead of 12.5
Thank you for your quick response and help !!
Hans
by hageha
Wed Oct 22, 2014 6:16 pm
Forum: OpenXVario - an open source vario supported by the open source firmwares!!
Topic: OpenXSensor SPORT Interface
Replies: 522
Views: 73830

Re: OpenXSensor SPORT Interface

and again it is me, after several hours, failed a new sensor with the Ver. 2.3 to get it to work. I want to transfer only Alti / Vario and the Lipo voltage. No single cell! (3 or 4) With the previous software, the sensor operates in both the "X" and in "D" mode Alti / Vario works. But no Voltage! He...
by hageha
Tue Sep 02, 2014 8:42 pm
Forum: OpenXVario - an open source vario supported by the open source firmwares!!
Topic: OpenXSensor SPORT Interface
Replies: 522
Views: 73830

Re: OpenXSensor SPORT Interface

o.k. I've assumed that you wanted to build an OpenXsensor!
by hageha
Sun Aug 24, 2014 2:14 pm
Forum: OpenXVario - an open source vario supported by the open source firmwares!!
Topic: OpenXSensor SPORT Interface
Replies: 522
Views: 73830

Re: OpenXSensor SPORT Interface

Ubatt is due to the pulse load by the motor / ESC not "clean".
By "C3" the disturbances are somewhat filtered.
by hageha
Sun Aug 24, 2014 12:00 pm
Forum: OpenXVario - an open source vario supported by the open source firmwares!!
Topic: OpenXSensor SPORT Interface
Replies: 522
Views: 73830

Re: OpenXSensor SPORT Interface

I have now made ​​even a simple design for a sensor with Alti / Vario and voltage display for 3 or 4 Lipo. Additional voltage regulator stabilizes the input voltage to approximately 8 volts. 4 pieces, as XR and DR version working properly http://www.ebay.de/itm/310862173882?_trksid=p2055119.m1438.l2...
by hageha
Sat Aug 09, 2014 6:58 pm
Forum: OpenXVario - an open source vario supported by the open source firmwares!!
Topic: OpenXSensor SPORT Interface
Replies: 522
Views: 73830

Re: OpenXSensor SPORT Interface

After I built several openXsensors represents for me the following question: Is it possible to build a sensor switchable for both systems, eg with a jumper? (XR-DR receiver) In the future I want to avoid getting to reprogram and use a new heat shrink tubing I have just the wrong sensor for the new r...
by hageha
Wed Jul 09, 2014 10:35 am
Forum: OpenXVario - an open source vario supported by the open source firmwares!!
Topic: OpenXSensor SPORT Interface
Replies: 522
Views: 73830

Re: OpenXSensor SPORT Interface

@ mstrens,
after many attempts, I ask again.
I have built the same device again and this time I want to run it with a D8R-II plus receiver.
Vario and altimeter is o.k. but I get no voltage output.
Maybe you can help me again.

Hans
by hageha
Tue Jul 08, 2014 4:22 pm
Forum: openTx
Topic: OpenTX 2.0.0
Replies: 300
Views: 99660

Re: OpenTX 2.0.0

I measure a 3 cell Lipo with a voltage divider
at "A2" of a "D8R-II plus" receiver.
Why I have to set, in the telemetry settings (10/10) from my Taranis (OpenTx 2.05 and before)
"FrSky S.PORT" to be able to read the values​​?
And not "FrSky D"
by hageha
Tue Jul 08, 2014 4:03 pm
Forum: openTx
Topic: OpenTx 2.0.5 Instant Trim not working properly
Replies: 8
Views: 1907

Re: OpenTx 2.0.5 Instant Trim not working properly

I measure a 3 cell Lipo with a voltage divider
at "A2" of a "D8R-II plus" receiver.
Why I have to set, in the telemetry settings (10/10) from my Taranis (OpenTx 2.05 and before)
"FrSky S.PORT" to be able to read the values​​?
And not "FrSky D"
by hageha
Tue Jun 03, 2014 9:33 pm
Forum: openTx
Topic: OpenTX - Nightly builds for pre-2.0 testing
Replies: 776
Views: 124836

Re: OpenTX - Nightly builds for pre-2.0 testing

Kilrah wrote:You need to load the new voice files too, there are new ones for that.
Update to 2.0 successfully!
I had to rename some of my Soundfiles.
There are only 8 characters for the names possible! (previously 10)

Many thanks to all involved
by hageha
Fri May 30, 2014 9:19 am
Forum: OpenXVario - an open source vario supported by the open source firmwares!!
Topic: OpenXSensor SPORT Interface
Replies: 522
Views: 73830

Re: OpenXSensor SPORT Interface

mstrens, thank you for your quick response.
I'll get to work and report the results.
Hans

Everything works very well - thank you -
by hageha
Wed May 28, 2014 6:33 pm
Forum: OpenXVario - an open source vario supported by the open source firmwares!!
Topic: OpenXSensor SPORT Interface
Replies: 522
Views: 73830

Re: OpenXSensor SPORT Interface

I try a 4 cell lipo on S port to measure.
Can I do this without individual cells over 4 voltage divider to measure?
If so, what settings do I have to put where?
Alti / Vario and a single cell works.
by hageha
Sat Nov 23, 2013 12:47 pm
Forum: FPV Projects
Topic: Open RSSI Antenna Tracker
Replies: 191
Views: 82501

Re: Open RSSI Antenna Tracker

My idea is to control pan and tilt independently. Pan, as in Bob's first version, with a continuously rotating servo. Tilt with a "180 degree" servo. One can then use cheap, strong, metal gear servos. However, the Act assumes that a wireless transmission of the video signal. Yes, I have it pinned! I...
by hageha
Wed Nov 20, 2013 6:16 pm
Forum: FPV Projects
Topic: Open RSSI Antenna Tracker
Replies: 191
Views: 82501

Re: Open RSSI Antenna Tracker

Rob,
you have the RSSI outputs of the receiver connected directly to the Arduino?
Or with resistors and possibly with capacitors blocked?
by hageha
Wed Nov 20, 2013 12:34 pm
Forum: FPV Projects
Topic: Open RSSI Antenna Tracker
Replies: 191
Views: 82501

Re: Open RSSI Antenna Tracker

before the flight. "is the grounstation battery o.k.?"
by hageha
Wed Nov 20, 2013 11:15 am
Forum: FPV Projects
Topic: Open RSSI Antenna Tracker
Replies: 191
Views: 82501

Re: Open RSSI Antenna Tracker

What do you think to integrate such a thing?
http://www.rcgroups.com/forums/showthread.php?t=1298192
by hageha
Tue Nov 19, 2013 11:10 am
Forum: The Pickled Gnu (The Pub)
Topic: Happy birthday to me!
Replies: 11
Views: 2164

Re: Happy birthday to me!

Happy Birthday Rob!
All the best for you.
by hageha
Thu Nov 07, 2013 1:17 pm
Forum: General help (FrSky Taranis radio)
Topic: XR8 rx telemetary sensors
Replies: 295
Views: 57956

Re: XR8 rx telemetary sensors

I think you must put Taranis to A2 = 13.2 volts.
by hageha
Tue Nov 05, 2013 9:33 pm
Forum: General help (FrSky Taranis radio)
Topic: XR8 rx telemetary sensors
Replies: 295
Views: 57956

Re: XR8 rx telemetary sensors

exactly
in the first 8 channel receivers, there was still no internal voltage divider at
A1. If you wanted to for example the 4.8 / 6 volt battery measured in a Glider, then the Grounds had to be connected
Ground is now connected via ESC/BEC.
by hageha
Tue Nov 05, 2013 9:18 pm
Forum: General help (FrSky Taranis radio)
Topic: XR8 rx telemetary sensors
Replies: 295
Views: 57956

Re: XR8 rx telemetary sensors

Alan, I once tried my experiences with 3 receivers that are burnt in connection with FRSKY voltage dividers and ESC with BEC to explain. It has happened in our club. Unfortunately, I can do that only with the help of translators. There were always connected while Lipo / ESC connections with banana p...
by hageha
Mon Oct 28, 2013 3:13 pm
Forum: General help (FrSky Taranis radio)
Topic: XR8 rx telemetary sensors
Replies: 295
Views: 57956

Re: XR8 rx telemetary sensors

The link shows a possible tool to program a ATTiny outside the board!
In this way, can be omitted in favor of the board size of the ISP plug.
by hageha
Sun Oct 27, 2013 6:17 pm
Forum: General help (FrSky Taranis radio)
Topic: XR8 rx telemetary sensors
Replies: 295
Views: 57956

Re: XR8 rx telemetary sensors

If we e.g. want to measure a LiPo with BEC, the Grounds should be separated! Otherwise, we have the same game as in the simple voltage dividers. Here is a simple, one-sided, onelayer, homemade version with balancer plug. With pre-programmed ATtiny. http://www.ebay.de/itm/350903644351?ssPageName=STRK...

Go to advanced search