Search found 8 matches

by currdog
Mon Dec 22, 2014 9:40 am
Forum: Software
Topic: Noob Needs Help Just to Set Up for Flashing 9x to Er9x
Replies: 8
Views: 1264

Re: Noob Needs Help Just to Set Up for Flashing 9x to Er9x

Thanks for the advise Daedalus66, I've done the calibration but that's all I've had time for between work and getting ready for Xmas with four kids!! I'm also in the middle of setting up a Bix2 with an Arkbird OSD autopilot and FPV gear. I've been trying to watch as many youtube vids on ER9x setting...
by currdog
Sat Dec 20, 2014 10:14 pm
Forum: Software
Topic: Noob Needs Help Just to Set Up for Flashing 9x to Er9x
Replies: 8
Views: 1264

Re: Noob Needs Help Just to Set Up for Flashing 9x to Er9x

Thanks Daedalus66, I just got back from my office where I was successful in installing the USBasp drivers on my Win7 computer. Installed eepe, downloaded the firmware, then flashed my 9x with the ER9x-FrSky-Noht firmware without a hitch!! Now I just have to figure out what the hell to do from here?!...
by currdog
Sat Dec 20, 2014 7:10 am
Forum: Software
Topic: Noob Needs Help Just to Set Up for Flashing 9x to Er9x
Replies: 8
Views: 1264

Re: Noob Needs Help Just to Set Up for Flashing 9x to Er9x

you know what? I think I'm getting the driver issue with Win8.1

I'm going to try the whole process with my computer at work running Win7 and see if I can get the drivers to work.

CurrDog
by currdog
Sat Dec 20, 2014 5:28 am
Forum: Software
Topic: Noob Needs Help Just to Set Up for Flashing 9x to Er9x
Replies: 8
Views: 1264

Re: Noob Needs Help Just to Set Up for Flashing 9x to Er9x

Daedalus66, Well I thought as much but when I attempted to plug a miniUSB cord from laptop into the miniUSB connector of the SM board, I got the following message... ================================================================================= Started AVRDUDE C:/Program Files (x86)/eePe/avrdude....
by currdog
Sat Dec 20, 2014 4:41 am
Forum: Software
Topic: Noob Needs Help Just to Set Up for Flashing 9x to Er9x
Replies: 8
Views: 1264

Noob Needs Help Just to Set Up for Flashing 9x to Er9x

Hi guys, I'm sorry if this has been asked/answered a hundred times already. I've searched the forum for answers for hours and found nada. I'm intending to flash my 9x to Er9x-FrSky-noht. I've got the FrSky DHT module installed. I've got the SmartieParts v2.4 programmer board and the TelemetrEZ board...
by currdog
Fri Dec 19, 2014 12:18 am
Forum: FRSky Telemetry Mods
Topic: How to Install TelemetrEZ with D.I.Y. FrSky Module?
Replies: 3
Views: 2409

Re: How to Install TelemetrEZ with D.I.Y. FrSky Module?

Ok, thanks Mike.

I assumed that was the case but what happens when you assume.......

With my luck I'd get the magic smoke and fry all my electronics.

CurrDog
by currdog
Thu Dec 18, 2014 9:32 pm
Forum: FRSky Telemetry Mods
Topic: How to Install TelemetrEZ with D.I.Y. FrSky Module?
Replies: 3
Views: 2409

Re: How to Install TelemetrEZ with D.I.Y. FrSky Module?

Ok Sorry guys, I'm a bit of a noob on these matters. After doing much more searching with alternate wordings I found this picture (see attached) which shows where to plug in the TelemetrEZ board to the FrSky DHT module. I wish they would say just to plug the FARKING thing into the side of the module...
by currdog
Wed Dec 17, 2014 4:53 am
Forum: FRSky Telemetry Mods
Topic: How to Install TelemetrEZ with D.I.Y. FrSky Module?
Replies: 3
Views: 2409

How to Install TelemetrEZ with D.I.Y. FrSky Module?

Hi Guys, I'm New to 9x, FrSky, Telemetry AND to the forum and just setting up my 9x with the Smartieparts hardware in preparation for the Er9x firmware update. Question #1, I had already installed the FrSky DHT (DIY) internal module inside my 9x before purchasing the smartieparts programmer and tele...

Go to advanced search