Search found 19 matches

by farlinoff
Thu Dec 18, 2014 7:46 am
Forum: er9x model setup
Topic: Trims not working as expected
Replies: 1
Views: 1917

Re: Trims not working as expected

Hi, I am replying to my own question. I discovered that I had the CrossTrim setting set to ON in the Txs SETTINGS / Controls menu. Turning that OFF solved the problem The flexibility of er9x is amazing but can be full of traps for new players like myself.

Regards,

Trevor
by farlinoff
Thu Dec 18, 2014 7:32 am
Forum: er9x model setup
Topic: Setting up dual rates for ailerons
Replies: 11
Views: 4689

Re: Setting up dual rates for ailerons

Hi Daedalus66 Again, thank you for your detailed response. I apologise for not getting back to you sooner but I am still trying to get my head around this stuff and I'm not finding it easy. I have been able to set up the Tx to work correctly physically but also need to actually understand what I am ...
by farlinoff
Thu Dec 18, 2014 7:00 am
Forum: er9x model setup
Topic: Trims not working as expected
Replies: 1
Views: 1917

Trims not working as expected

Hi, I am using er9x, SVN: er9x-r813, VERS: V1.275-Mike and recently noticed that the trims on my Tx are not working as expected. My Tx is Mode 1 and the er9x mix settings are CH1: +100%RUD, Ch2: +100%ELE, CH3: +100%THR, CH4: +100%AIL This all works perfectly with my Rx which has Ch1: connected to Ai...
by farlinoff
Sat Dec 13, 2014 5:53 am
Forum: er9x model setup
Topic: Setting up dual rates for ailerons
Replies: 11
Views: 4689

Re: Setting up dual rates for ailerons

Hi, Thanks very much for your comprehensive answer. I have done some experimenting based upon what you have written and think I understand what you are saying. My Tx is a Mode 1 (Right stick Throttle and Aileron, Left stick Elevator and Rudder) and I am happy with this arrangement. When in the eePe ...
by farlinoff
Sat Dec 13, 2014 1:44 am
Forum: er9x model setup
Topic: Setting up dual rates for ailerons
Replies: 11
Views: 4689

Re: Setting up dual rates for ailerons

Hi Mike, Thanks for that, I now understand how to use the simulator but alas the dual rates I have set up do not work in the simulator so the plot thickens I have another question though...I am using an Rx which comes with the Turnigy Tx and by default, this Rx expects Ailerons on its Channel 1, Ele...
by farlinoff
Thu Dec 11, 2014 10:49 am
Forum: er9x model setup
Topic: Setting up dual rates for ailerons
Replies: 11
Views: 4689

Re: Setting up dual rates for ailerons

Hi Mike, Thanks for your very prompt reply. I have attempted to follow your instructions but have not had any success as yet. I have attached a dump of the relevant screen from eePe as a .jpg file so you can see clearly what settings I have made. Would you please have a look at these to see what I a...
by farlinoff
Thu Dec 11, 2014 7:21 am
Forum: er9x model setup
Topic: Setting up dual rates for ailerons
Replies: 11
Views: 4689

Setting up dual rates for ailerons

Hi, I am trying to set up dual rates for ailerons but have had no success. I am using er9x, SVN: er9x-r813, VERS: V1.275-Mike and am attempting to use the setup EXPO/DR screen . The screen dumps in the doco. located at http://openrcforums.com/wiki/index.php/Er9x_user_guide are quite different to my ...
by farlinoff
Wed Nov 19, 2014 9:51 am
Forum: er9x
Topic: Buddying two Turnigy 9xs upgraded to Er9x firmware
Replies: 13
Views: 1837

Re: Buddying two Turnigy 9xs upgraded to Er9x firmware

Wow, 2 good suggestions for the manual in one go. :) you don't see this everyday. Excellent :D Hi jhsa, Thanks for your positive comment. I have to say that this Forum is just fantastic and I have been so pleased to contribute material which will assist others to run the very important and useful b...
by farlinoff
Wed Nov 19, 2014 9:44 am
Forum: er9x
Topic: Buddying two Turnigy 9xs upgraded to Er9x firmware
Replies: 13
Views: 1837

Re: Buddying two Turnigy 9xs upgraded to Er9x firmware

Good. On the SAFETY SWITCHES, you have seen the S and A options. You also have a V option (for when you have a voice module added), and, on recent revisions of er9x, you also have an X option. The X option is also the safety switch, like S, but this is "sticky". What this means is the throttle safe...
by farlinoff
Fri Nov 14, 2014 6:12 am
Forum: er9x
Topic: Buddying two Turnigy 9xs upgraded to Er9x firmware
Replies: 13
Views: 1837

Re: Buddying two Turnigy 9xs upgraded to Er9x firmware

Hi Mike and Reinhard Thank you both for continuing to help me with this one. Thanks to your collective advice I have now got the throttle working perfectly and now properly understand the Calibration process of the Student Tx. What I had not told you was that I have implemented a throttle safety fea...
by farlinoff
Thu Nov 13, 2014 7:34 pm
Forum: er9x
Topic: Buddying two Turnigy 9xs upgraded to Er9x firmware
Replies: 13
Views: 1837

Re: Buddying two Turnigy 9xs upgraded to Er9x firmware

Hi Reinhard

Thanks for continuing to help. I am still working on this, will get back to you when I have more to say in terms of results

Regards

Trevor
by farlinoff
Wed Nov 12, 2014 9:31 pm
Forum: er9x
Topic: Buddying two Turnigy 9xs upgraded to Er9x firmware
Replies: 13
Views: 1837

Re: Buddying two Turnigy 9xs upgraded to Er9x firmware

Hi Reinhard Thanks for responding to my problem. Yes, I did set the students throttle stick to the middle position before performing the Cal function on the instructors Tx. I have done this several times now and always get the same result. In order to recover from this result I have had to re-write ...
by farlinoff
Wed Nov 12, 2014 10:27 am
Forum: er9x
Topic: Buddying two Turnigy 9xs upgraded to Er9x firmware
Replies: 13
Views: 1837

Buddying two Turnigy 9xs upgraded to Er9x firmware

Hi Forum I have been attempting to buddy up two Turnigy 9x Txs using the instructions at http://openrcforums.com/wiki/index.php/Er9x_setup_buddy_box_Instructor/Student and have been successful apart from one issue which I don't fully understand. The Instructor Setup contains a step as follows Step 6...
by farlinoff
Fri Oct 24, 2014 8:27 pm
Forum: er9x
Topic: Buddying two Turnigy 9xs upgraded to Er9x firmware
Replies: 6
Views: 995

Re: Buddying two Turnigy 9xs upgraded to Er9x firmware

On the student Tx, have you turned PPMSIM on? Doing so routes the trainer output through different circuitry so any installed module, which is not powered in student mode, doesn't load the trainer signal. Sorry, I've not had time to download your .eepe files (yet). Mike. Hi Mike :D Thanks very much...
by farlinoff
Fri Oct 24, 2014 7:57 pm
Forum: er9x
Topic: Buddying two Turnigy 9xs upgraded to Er9x firmware
Replies: 6
Views: 995

Re: Buddying two Turnigy 9xs upgraded to Er9x firmware

:D How are you powering the slave radiio? Don't turn the power switch on. Just connect the trainer cable to it with the power switch off. The radio will turn on and will send ppm on the trainer port. The master tx needs of course to be on before you connect the trainer cable to it. João Thanks for r...
by farlinoff
Fri Oct 24, 2014 8:07 am
Forum: er9x
Topic: Buddying two Turnigy 9xs upgraded to Er9x firmware
Replies: 6
Views: 995

Buddying two Turnigy 9xs upgraded to Er9x firmware

Dear Forum I have 2 new Turnigy 9x Txs both of which have been firmware upgraded to SVN: er9x-r813. VERS: V1.275-Mike DATE: 14.08.2014 TIME:13:26:53 MOD: I am connecting them through a buddy cable supplied by Hobbyking for the Turnigy 9x. I have followed exactly the instructions given at http://open...
by farlinoff
Sat Oct 04, 2014 8:00 am
Forum: Software
Topic: .bin and .hex files using eepe er9x eeprom editor
Replies: 6
Views: 1660

Re: .bin and .hex files using eepe er9x eeprom editor

Hi Kilrah and jhsa, Thanks for your responses, I will have a search through the forum's stock firmware and look forward to a copy of the flysky firmware if you remember.
Regards, Trevor
by farlinoff
Fri Oct 03, 2014 11:49 pm
Forum: Software
Topic: .bin and .hex files using eepe er9x eeprom editor
Replies: 6
Views: 1660

Re: .bin and .hex files using eepe er9x eeprom editor

Hi Mike, Thanks your rapid response, a further question. Are you saying that if I use the 'read firmware from Tx' option using eepe, it does not matter whether I save this as a .bin or a .hex file. Also when I first loaded er9x I forgot to use the 'read firmware from Tx' option to save the old Turni...
by farlinoff
Fri Oct 03, 2014 10:18 pm
Forum: Software
Topic: .bin and .hex files using eepe er9x eeprom editor
Replies: 6
Views: 1660

.bin and .hex files using eepe er9x eeprom editor

I am a newcomer to er9x and would like to know the functional difference between .hex and .bin files in use with the eepe er9x eeprom editor?
Regards, Trevor Farley (farlinoff)

Go to advanced search