openrcforums

Hi all,
Can a modern tgy 9x transmitter be flashed with ER9x software, the system uses the Flysky 2a mode receivers?
I recall some time ago this question arose and a solution of changing polarity was made. Does this work, or are there any other tweaks to get the system and ER9X working?
TIA
Tony S

Thanks for that Mike!
Looking like an interesting time next time I visit the club pond!
Cheers
Tony

Hi all,
Been looking around to see if there is a program within the 9XR Pro system to set up an exponential servo operation without plotting said curve in curves? ---- I want to try on the steering of a boat!
Thanks in advance

ok, have achieved an equilibrium with the two motors using the sub trim settings for both motors in the limits area.
I am now a happy bunny, thanks Mike.
I have added this to my little book of crib notes, again many thanks!

They are un named chinese pieces costing about 5 - 6€, 10amp with a 20 instantaneous, no central brake function, so straight from forward to reverse! The two motors, when both run with the same directional rotation start together in both directions. Because the motors are being run anti clockwise an...

Hi all Bloavez mad / Happy New Year one and all! The following might need moving to a more appropriate forum topic! I have been asked by a modelling colleague to set up his 9XR Pro to control a 2 motored boat. Fine, i have installed V tail mixing and have both motors working fine. I have a small pro...

Hi all
Is there a handbook that outlines the various functions and there uses?
I am a complete novice after programing the basic functions
Thanks in advance
Tony S

Hi all Finally got back to fiddling with tis, and using the link by ReSt and the setup suggested by pstimpel I have more or less what i want, the Tank rolls as expected, the only piece missing is the horiz left and right sticks do not generate anything for this situation, not a problem , the tank is...

Nope, didn't work, as above tracks rolling in opposite directions when in fwd and rev.
I'll knock up a test thingy later to test/check the programming, ie 2 x motors with tell tales on the shafts with a similar receiver etc!

Tried that, didn't work, the left and right tracks were rolling in opposite directions!

You have listed 2 x CH1's, should the 2nd one be CH2?
I am just about to load the settings, and will use the 2nd CH! as CH2
I'll get back to you in due course!

Thanks for the speedy reply, I think the latter situation would work best, the tank will be part of a demonstration piece with a landing craft and the disembarquation etc. I thought the V programming would have worked on the tank, it has been used on the landing craft without probs for some time! ag...

Hi all, As above, I am trying to set the tx to control a tank, have used the plane 'v' tail mix. Ok it is set up as follows Ch1 50% Rud + 50% Elev Ch2 50% Rud + -50% Elev For the most part it works fine, however when turning to the left with the stick in top left position ie going forwards, works fi...

Hi all
I want to download the above manual the system keeps falling over because of phishing stuff, how can i do it?
cheers
Tony

no same, as before
i'll try remaking the ribbon cable joint feeding the screen later

11.5v
tomorrow i will try a different sd card, if it works i'll reflash the system!

nope, nothing!

ok, my error, missed the 9, its a
Tgy 9XR Pro
Hopefully I will get back to it either later today or tomorrow / or weekend!

Ok, its been awhile!
I have an XRPro,just started to look at upgrading to Er9xsoftware,swithched on, power to indicator light,but no screen illumination, can anyone point me at postings etc on here, i recall some several years ago but cannot find them!
Thanks

So, set up an rf module and an rx with servos connected tried the bind procedure, it bound, switched all off, removed bind loop, switched on, tx then rx -no led showing in rx.no servo movement Switch on pressing horiz bars, connect nothing and the voltage check, with the rf board mounted or on its o...

Yes, getting continuity across it with a reading of 0.7 ohms - a jumper wire perhaps?

Ok, cleaned/remade all connections in the tx, still nothing, only the power on blue light, also with the tx connected to my laptop, it is not detected, any suggestions please?

No , its not that, any other suggestions, later today I will clean all the plugs sockets and re make the screen connection etc

Hi all Been a while, lost/misplaced my notes, I have a Pro tx, powering on, the blue power light works but screen remains 'dead' I remember a fix for this(dead resistor of 0ohms I think, just needing a bridge) but cannot find the piece, any suggestions please, and finally mr dumb here asking, a stra...

Another quick question, got cm621 clone rx , using with a 9xr pro and orangerx dsm2/dsmx module setup in protocols as normal, it binds fine, then when bind cable removed and rebooted with a motor and servo's connected, all works fine for a couple of mins then the motor goes to full speed and the ser...

yeap they are the ones, I also used my last one recently!!- I have an old board somewhere there might be one or two on it, i'll try to locate it over the weekend!

Ah ok, the fog clears a little!!
Thanks

Thanks Mike, its Strangeas I have an Orangerx DSM2/DSMX dedicated for an XR2Pro, In protocos all options listed, but in Multi and Flysky x2 the unit will not bind, told by Hobbyking the module is only DSM2/DSMX, so why list all rhe rest?

Another question to clarify in my mind, the protocols are stored in the Tx hardware or in the tx module hardware?

ah ok, I begin to understand!!