openrcforums

This guide is very useful, very good job
a little contribution;
In txt file for notes you can see the up and down arrow adding "\dn" and "\up" after the switche name
SA\dn
SB\up
I think you could add this information in "How to Create txt files" section

I have found a workaround

Special Function
ON Adjust GV2 Source CH1

Logical Switches
L1 a<b GV2 GV1

I don't know if exist other solution, but in this way my program works ok

Companion 2.1.8

With logical switch

L1 a>x CH1 50
L1 goes true when CH1 position is 50%


L2 a>b CH1 GV1 with GV1=50
L2 goes true when CH1=5,4%

Is this a correct behaviour?

Thanks

Actually filter is disabled, time with filter becomes 3 seconds If link between radio and receiver break the error condition is generated only after 2 seconds? If RX Power down is up to 1,5 seconds Servo stops but non error are generated Another question: SWR measurement change quickly from 17 to 0 ...

Hi OpenTX 2.1 and Taranis If on receiver the power supply go down for a time lower than 1,5 seconds on TX no error message are generated In case of a very fast reaction probably many message would be generated creating false alarm but in case of temporary false contact in power supply line would be ...

Thank you for information
Hardware option for Jitter filter is very interesting

Hi
For curiosity: when the openTx 2.1.9 release is planned?

Ask in FRSKY forum
http://www.frsky-rc.com/BBS/viewtopic.p ... 1e743dc485

EEPROM is more reliable than SD
Why this choise?

Are on Horus model parameter memorized in EEPROM or in SD card only?
On frsky web site is declared:
"SD Card (no EEPROM)"

Perfect!
Arrow now are visualized

Thanks

When notes are visualized on display of Taranis may be useful to use special characters like up or down arrow for switch positions
In which way is possible that?

Thanks

I do not agree that those who use the BEC are the majority in many categories it is common to use more traditional batteries without regulator. in any case it is not certain that the bec functions regularly and the RX poewr supply voltage can be an interesting parameter to check. Of course I realize...

The rx battery low voltage alarm in 2.0 was the "A1 low or critical level" configurable in configuration menu Now in 2.1 the same function must be configured by logical switch an special functions In every models this is the first fundamental telemetry option used for safety. why not have ...

Kilrah wrote:You didn't way what recevier and protocol you were using.
.

You are right!
Taranis with X8R
Sometimes is little bit annoying the alarm message , but your explanation comforts me
Thanks

sometimes during the fly a low signal message is played if the time required for trigger the low signal condition by 5 low value is very short, probabily increasing the number of average the number of message decrease without compromise the security. Naturally You Know very well than me this functio...

in that time there's 5 values?

Hi
When RSSI signal go down the programmed value give an Low or Critical message .
To trigger this alarm is sufficient that the signal falls below the threshold only once or needs to happen for several times?

How this work?

Thank you

.......associate a source such as a potentiometer ........ Potentiometers may be the on board radio S1 S2 LS RS, this permit a software simulation. if source of variometer is a virtual input is possible to associate sound at different parameter like altitude velocity distance or others in this way ...

Your suggestions are very interesting and I will try them I don't know if is difficult to realize, but I thought of providing an additional source of the VSI that could be a virtual input I this case it would be possible to associate a source such as a potentiometer and this would allow you to explo...

Hi
On taranis variometer sound in very useful
is possible to simulate it on radio (ie moving an input source ) in order to optimize the sound ?
Is possible to create a dedicate input like a source for variometer?

An issue in OpenTx was opened
https://github.com/opentx/opentx/issues/1954

Hi before every official release of last version of OpenTx I think may be usefull to create a Release Candidate for bugs hunting. In this case some users know that is a non stable version but they can help to find bugs In the past in some cases a bug was discovered immediately after release forcing ...

Thank you for informations
We wait good news

Uhm. .. dont understand the question? My question about OpenTx? In other words: Someone have started the project for a new OpenTx version for Horus? is the intention of the OpenTx developers to make a version for Horus? For the moment OpenTx is only for taranis and taranis Plus (I know) I hope that...

Hi
Someone have a notice about OpenTx for Horus?

Kilrah wrote:Did you build companion yourself? If yes you should use the master branch (2.0.x), not next (2.1.x). It is definitely not present in release 2.0.10 version.

Yes, compiled from next
Mystery solved!
Thanks

bertrand35 wrote:Timer3 will be introduced in OpenTX 2.1.0 which was never released!

In Companion Taranis simulator is present

Hi
I have just upgraded my Taranis from 2.08 to 2.010 (italian version) and Timer3 is not present in setup menu.
I can see it in Companion Radio simulator
Why?

Lua becomes every day more powerfull and big.
Is possile use bytecode?
In Companion Lua Ide a scripts is created and converted in bytecode.
Inside the radio a runtime Lua interpreter read and esecute the program
May this be an optimisation?