This guide is very useful, very good job
a little contribution;
In txt file for notes you can see the up and down arrow adding "\dn" and "\up" after the switche name
SA\dn
SB\up
I think you could add this information in "How to Create txt files" section
Search found 66 matches
- Sun Sep 25, 2016 8:25 pm
- Forum: openTx
- Topic: Documentation for OpenTX 2.2 Taranis and Horus
- Replies: 89
- Views: 228005
- Wed Sep 14, 2016 12:37 pm
- Forum: openTx
- Topic: Different behaviour of CHx against GVAR in logical switches
- Replies: 2
- Views: 2658
Re: Different behaviour of CHx in logical switches
I have found a workaround
Special Function
ON Adjust GV2 Source CH1
Logical Switches
L1 a<b GV2 GV1
I don't know if exist other solution, but in this way my program works ok
Special Function
ON Adjust GV2 Source CH1
Logical Switches
L1 a<b GV2 GV1
I don't know if exist other solution, but in this way my program works ok
- Wed Sep 14, 2016 10:32 am
- Forum: openTx
- Topic: Different behaviour of CHx against GVAR in logical switches
- Replies: 2
- Views: 2658
Different behaviour of CHx against GVAR in logical switches
Companion 2.1.8
With logical switch
L1 a>x CH1 50
L1 goes true when CH1 position is 50%
L2 a>b CH1 GV1 with GV1=50
L2 goes true when CH1=5,4%
Is this a correct behaviour?
Thanks
With logical switch
L1 a>x CH1 50
L1 goes true when CH1 position is 50%
L2 a>b CH1 GV1 with GV1=50
L2 goes true when CH1=5,4%
Is this a correct behaviour?
Thanks
- Sun Sep 11, 2016 6:07 pm
- Forum: openTx
- Topic: If receiver lost power for 1 second non error message on TX
- Replies: 2
- Views: 2659
Re: If receiver lost power for 1 second non error message on TX
Actually filter is disabled, time with filter becomes 3 seconds If link between radio and receiver break the error condition is generated only after 2 seconds? If RX Power down is up to 1,5 seconds Servo stops but non error are generated Another question: SWR measurement change quickly from 17 to 0 ...
- Sun Sep 11, 2016 9:21 am
- Forum: openTx
- Topic: If receiver lost power for 1 second non error message on TX
- Replies: 2
- Views: 2659
If receiver lost power for 1 second non error message on TX
Hi OpenTX 2.1 and Taranis If on receiver the power supply go down for a time lower than 1,5 seconds on TX no error message are generated In case of a very fast reaction probably many message would be generated creating false alarm but in case of temporary false contact in power supply line would be ...
- Tue Aug 02, 2016 9:56 am
- Forum: openTx
- Topic: OpenTx 2.1.9: When?
- Replies: 2
- Views: 2747
Re: OpenTx 2.1.9: When?
Thank you for information
Hardware option for Jitter filter is very interesting
Hardware option for Jitter filter is very interesting
- Tue Aug 02, 2016 7:47 am
- Forum: openTx
- Topic: OpenTx 2.1.9: When?
- Replies: 2
- Views: 2747
OpenTx 2.1.9: When?
Hi
For curiosity: when the openTx 2.1.9 release is planned?
For curiosity: when the openTx 2.1.9 release is planned?
- Mon Feb 01, 2016 7:19 pm
- Forum: FRSky Horus radio
- Topic: [Horus]EEPROM missing?
- Replies: 7
- Views: 7290
Re: [Horus]EEPROM missing?
Ask in FRSKY forum
http://www.frsky-rc.com/BBS/viewtopic.p ... 1e743dc485
http://www.frsky-rc.com/BBS/viewtopic.p ... 1e743dc485
- Fri Jan 29, 2016 3:15 pm
- Forum: FRSky Horus radio
- Topic: [Horus]EEPROM missing?
- Replies: 7
- Views: 7290
Re: [Horus]EEPROM missing?
EEPROM is more reliable than SD
Why this choise?
Why this choise?
- Fri Jan 29, 2016 1:41 pm
- Forum: FRSky Horus radio
- Topic: [Horus]EEPROM missing?
- Replies: 7
- Views: 7290
[Horus]EEPROM missing?
Are on Horus model parameter memorized in EEPROM or in SD card only?
On frsky web site is declared:
"SD Card (no EEPROM)"
On frsky web site is declared:
"SD Card (no EEPROM)"
- Sun Jan 10, 2016 5:42 pm
- Forum: openTx
- Topic: Display special characters in notes on Taranis
- Replies: 2
- Views: 3003
Re: Display special characters in notes on Taranis
Perfect!
Arrow now are visualized
Thanks
Arrow now are visualized
Thanks
- Sun Jan 10, 2016 9:48 am
- Forum: openTx
- Topic: Display special characters in notes on Taranis
- Replies: 2
- Views: 3003
Display special characters in notes on Taranis
When notes are visualized on display of Taranis may be useful to use special characters like up or down arrow for switch positions
In which way is possible that?
Thanks
In which way is possible that?
Thanks
- Mon Oct 19, 2015 9:03 am
- Forum: openTx
- Topic: RX voltage alarm in 2.1
- Replies: 4
- Views: 3961
Re: RX voltage allarm in 2.1
I do not agree that those who use the BEC are the majority in many categories it is common to use more traditional batteries without regulator. in any case it is not certain that the bec functions regularly and the RX poewr supply voltage can be an interesting parameter to check. Of course I realize...
- Sun Oct 18, 2015 1:53 pm
- Forum: openTx
- Topic: RX voltage alarm in 2.1
- Replies: 4
- Views: 3961
RX voltage alarm in 2.1
The rx battery low voltage alarm in 2.0 was the "A1 low or critical level" configurable in configuration menu Now in 2.1 the same function must be configured by logical switch an special functions In every models this is the first fundamental telemetry option used for safety. why not have ...
- Sun Oct 11, 2015 3:17 pm
- Forum: openTx
- Topic: TARANIS with X8R: Question about Low signal allarm
- Replies: 6
- Views: 4280
Re: Question about Low signal allarm
You are right!Kilrah wrote:You didn't way what recevier and protocol you were using.
.
Taranis with X8R
Sometimes is little bit annoying the alarm message , but your explanation comforts me
Thanks
- Sun Oct 11, 2015 1:10 pm
- Forum: openTx
- Topic: TARANIS with X8R: Question about Low signal allarm
- Replies: 6
- Views: 4280
Re: Question about Low signal allarm
sometimes during the fly a low signal message is played if the time required for trigger the low signal condition by 5 low value is very short, probabily increasing the number of average the number of message decrease without compromise the security. Naturally You Know very well than me this functio...
- Sun Oct 11, 2015 12:10 pm
- Forum: openTx
- Topic: TARANIS with X8R: Question about Low signal allarm
- Replies: 6
- Views: 4280
Re: Question about Low signal allarm
in that time there's 5 values?
- Sun Oct 11, 2015 11:56 am
- Forum: openTx
- Topic: TARANIS with X8R: Question about Low signal allarm
- Replies: 6
- Views: 4280
TARANIS with X8R: Question about Low signal allarm
Hi
When RSSI signal go down the programmed value give an Low or Critical message .
To trigger this alarm is sufficient that the signal falls below the threshold only once or needs to happen for several times?
How this work?
Thank you
When RSSI signal go down the programmed value give an Low or Critical message .
To trigger this alarm is sufficient that the signal falls below the threshold only once or needs to happen for several times?
How this work?
Thank you
- Thu Jun 04, 2015 9:12 am
- Forum: openTx
- Topic: How to simulate variometer sound?
- Replies: 11
- Views: 7445
Re: How to simulate variometer sound?
.......associate a source such as a potentiometer ........ Potentiometers may be the on board radio S1 S2 LS RS, this permit a software simulation. if source of variometer is a virtual input is possible to associate sound at different parameter like altitude velocity distance or others in this way ...
- Fri May 29, 2015 7:30 am
- Forum: openTx
- Topic: How to simulate variometer sound?
- Replies: 11
- Views: 7445
Re: How to simulate variometer sound?
Your suggestions are very interesting and I will try them I don't know if is difficult to realize, but I thought of providing an additional source of the VSI that could be a virtual input I this case it would be possible to associate a source such as a potentiometer and this would allow you to explo...
- Tue May 26, 2015 10:30 am
- Forum: openTx
- Topic: How to simulate variometer sound?
- Replies: 11
- Views: 7445
How to simulate variometer sound?
Hi
On taranis variometer sound in very useful
is possible to simulate it on radio (ie moving an input source ) in order to optimize the sound ?
Is possible to create a dedicate input like a source for variometer?
On taranis variometer sound in very useful
is possible to simulate it on radio (ie moving an input source ) in order to optimize the sound ?
Is possible to create a dedicate input like a source for variometer?
- Sun Feb 22, 2015 7:38 am
- Forum: openTx
- Topic: Special characters in checklist note on Taranis
- Replies: 5
- Views: 5642
Re: Special characters in checklist note on Taranis
An issue in OpenTx was opened
https://github.com/opentx/opentx/issues/1954
https://github.com/opentx/opentx/issues/1954
- Sun Feb 22, 2015 7:31 am
- Forum: openTx
- Topic: Release candidate
- Replies: 15
- Views: 8631
Release candidate
Hi before every official release of last version of OpenTx I think may be usefull to create a Release Candidate for bugs hunting. In this case some users know that is a non stable version but they can help to find bugs In the past in some cases a bug was discovered immediately after release forcing ...
- Fri Oct 03, 2014 3:58 pm
- Forum: FRSky Horus radio
- Topic: FrSky X12D or X16D...?
- Replies: 42
- Views: 45708
Re: FrSky X12D or X16D...?
Thank you for informations
We wait good news
We wait good news
- Fri Oct 03, 2014 3:00 pm
- Forum: FRSky Horus radio
- Topic: FrSky X12D or X16D...?
- Replies: 42
- Views: 45708
Re: FrSky X12D or X16D...?
Uhm. .. dont understand the question? My question about OpenTx? In other words: Someone have started the project for a new OpenTx version for Horus? is the intention of the OpenTx developers to make a version for Horus? For the moment OpenTx is only for taranis and taranis Plus (I know) I hope that...
- Fri Oct 03, 2014 10:43 am
- Forum: FRSky Horus radio
- Topic: FrSky X12D or X16D...?
- Replies: 42
- Views: 45708
Re: FrSky X12D or X16D...?
Hi
Someone have a notice about OpenTx for Horus?
Someone have a notice about OpenTx for Horus?
- Tue Sep 09, 2014 9:29 pm
- Forum: openTx
- Topic: OpenTx 2.0.10 timer3 disappeared
- Replies: 4
- Views: 4000
Re: OpenTx 2.0.10 timer3 disappeared
Yes, compiled from nextKilrah wrote:Did you build companion yourself? If yes you should use the master branch (2.0.x), not next (2.1.x). It is definitely not present in release 2.0.10 version.
Mystery solved!
Thanks
- Tue Sep 09, 2014 9:03 pm
- Forum: openTx
- Topic: OpenTx 2.0.10 timer3 disappeared
- Replies: 4
- Views: 4000
Re: OpenTx 2.0.10 timer3 disappeared
In Companion Taranis simulator is presentbertrand35 wrote:Timer3 will be introduced in OpenTX 2.1.0 which was never released!
- Tue Sep 09, 2014 8:20 pm
- Forum: openTx
- Topic: OpenTx 2.0.10 timer3 disappeared
- Replies: 4
- Views: 4000
OpenTx 2.0.10 timer3 disappeared
Hi
I have just upgraded my Taranis from 2.08 to 2.010 (italian version) and Timer3 is not present in setup menu.
I can see it in Companion Radio simulator
Why?
I have just upgraded my Taranis from 2.08 to 2.010 (italian version) and Timer3 is not present in setup menu.
I can see it in Companion Radio simulator
Why?
- Fri Jul 11, 2014 6:55 am
- Forum: openTx
- Topic: Ide for Lua in Companion
- Replies: 2
- Views: 2802
Re: Ide for Lua in Companion
Lua becomes every day more powerfull and big.
Is possile use bytecode?
In Companion Lua Ide a scripts is created and converted in bytecode.
Inside the radio a runtime Lua interpreter read and esecute the program
May this be an optimisation?
Is possile use bytecode?
In Companion Lua Ide a scripts is created and converted in bytecode.
Inside the radio a runtime Lua interpreter read and esecute the program
May this be an optimisation?