Search found 142 matches

by PNaz
Tue Oct 11, 2016 3:26 am
Forum: erskyTx (was ersky9x)
Topic: FrSky Redundancy Bus
Replies: 33
Views: 5398

Re: FrSky Redundancy Bus

Those numbers look logical but why the different numbers when receiver is disconnected after power up?
by PNaz
Mon Oct 10, 2016 11:29 pm
Forum: erskyTx (was ersky9x)
Topic: FrSky Redundancy Bus
Replies: 33
Views: 5398

Re: FrSky Redundancy Bus

Quick test with the R219x2 firmware gave RBST 648 when powering up with RX 2 disconnected and 1312 when powering up with RX 1 disconnected. Log doesn't show any other numbers when powering up. Just 0 then 648 or 1312. It goes back to 0 if the receiver is connected.

Paul
by PNaz
Mon Oct 10, 2016 7:19 pm
Forum: erskyTx (was ersky9x)
Topic: FrSky Redundancy Bus
Replies: 33
Views: 5398

Re: FrSky Redundancy Bus

I just checked a log file. All 0 for RBST until I disconnected RX2 then it went to 136 and stayed there until I reconnected RX 2. Right back to 0. I turned off the external module and RBST then went to 16 for a single reading and then to 24 for the rest of the readings until turning the module back ...
by PNaz
Mon Oct 10, 2016 5:12 pm
Forum: erskyTx (was ersky9x)
Topic: FrSky Redundancy Bus
Replies: 33
Views: 5398

Re: FrSky Redundancy Bus

I also tested a voice switch with the logic switch you suggested. It works correctly if I use the actual numbers displayed for RBST
e.g. Dec 288 for bit 7 instead of your example of 128

Paul
by PNaz
Mon Oct 10, 2016 4:36 pm
Forum: erskyTx (was ersky9x)
Topic: FrSky Redundancy Bus
Replies: 33
Views: 5398

Re: FrSky Redundancy Bus

My testing of the latest redundancy bus revision reveals some unexpected numbers. RBST gives a decimal number of 288 (128) for bit 7 on, 136 (256) for bit 8 on, 96 (512) for bit 9 on, and 24 (1024) for bit 10 on. Receivers were switched positions on the redundancy bus and rebound in order to always ...
by PNaz
Sat Oct 08, 2016 8:42 pm
Forum: erskyTx (was ersky9x)
Topic: FrSky Redundancy Bus
Replies: 33
Views: 5398

Re: FrSky Redundancy Bus

Mike It looks like you have a workable solution to the problem if you can also latch the bit as Kilrah has suggested. If you can reset the latch after a voice file has been triggered and a screen or log entry written that increments the error count then that would work well enough for troubleshootin...
by PNaz
Sat Oct 08, 2016 12:51 am
Forum: erskyTx (was ersky9x)
Topic: FrSky Redundancy Bus
Replies: 33
Views: 5398

Re: FrSky Redundancy Bus

The PB** data messages are displaying well. Voice announcements of the data can be handled exactly like the other FrSky sensors displaying volts, amps, or mah. I think the way FrSky shows the data messages will work ok and can easily trigger a voice message. It looks like they poll each individual b...
by PNaz
Fri Oct 07, 2016 3:55 pm
Forum: erskyTx (was ersky9x)
Topic: FrSky Redundancy Bus
Replies: 33
Views: 5398

Re: FrSky Redundancy Bus

Further testing shows RBST does go from -2048 to -1912 when the non telelmetry receiver RX2 is disconnected. It was very intermittant. That problem was probably caused by the problem of having the transmitter close enough to read the data on the screen but far enough away to receive the telemetry. O...
by PNaz
Fri Oct 07, 2016 2:11 pm
Forum: ersky9xr
Topic: x4r
Replies: 50
Views: 5293

Re: x4r

João. I have used the unique capabilities of the X4R-SB for a GWS Cargotrans. It has 4 small outrunners with esc's so 1 esc is plugged into ch1 for left outboard motor , 2 esc's with y harness into ch2 for the inboard motors, and 1 esc into ch3 for the right outboard motor. This way I can simulate a...
by PNaz
Fri Oct 07, 2016 12:54 am
Forum: erskyTx (was ersky9x)
Topic: FrSky Redundancy Bus
Replies: 33
Views: 5398

Re: FrSky Redundancy Bus

Mike. I tried the new test version and do get two more selections, RBSV and RBST. These are not what FrSky shows as status messages. When I power up the Redundancy bus RBSV reads 0 and RBST reads -2048. Disconnecting one of the receivers or one of the batteries to simulate a failure results in no ch...
by PNaz
Wed Oct 05, 2016 12:54 am
Forum: erskyTx (was ersky9x)
Topic: FrSky Redundancy Bus
Replies: 33
Views: 5398

Re: FrSky Redundancy Bus

Mike I just tried out the new test version with the Redundancy Bus additions. There is a problem. When going through to list I still get the original six items RBv1 RBa1 RBv2 Rba2 RBm1 and RBm2. The it gets weird. The next selection ends up as a flashing -- situated at the 5th and 6th character posi...
by PNaz
Wed Oct 05, 2016 12:24 am
Forum: erskyTx (was ersky9x)
Topic: FrSky Redundancy Bus
Replies: 33
Views: 5398

Re: FrSky Redundancy Bus

Thanks Mike. I will try it out.

Paul
by PNaz
Mon Oct 03, 2016 2:04 pm
Forum: erskyTx (was ersky9x)
Topic: FrSky Redundancy Bus
Replies: 33
Views: 5398

Re: FrSky Redundancy Bus

Thanks Mike. There is no rush on this. The model is not completed and the redundancy bus should work properly as is. The data we are talking about will only tell me if the bus is actually encountering problems and compensating for them.

Paul
by PNaz
Mon Oct 03, 2016 1:26 pm
Forum: erskyTx (was ersky9x)
Topic: FrSky Redundancy Bus
Replies: 33
Views: 5398

Re: FrSky Redundancy Bus

I have a Taranis using the internal module to a X4R receiver and a XJT external module to a X6R receiver. Both receivers are attached to the Redundancy bus via S.Bus. The X6R has telemetry disabled as per the instruction sheet.I can turn off either the internal or external module and still maintain ...
by PNaz
Mon Oct 03, 2016 2:07 am
Forum: erskyTx (was ersky9x)
Topic: FrSky Redundancy Bus
Replies: 33
Views: 5398

FrSky Redundancy Bus

I have just received a Frsky Redundancy Bus for a large aerobatic model. http://www.frsky-rc.com/product/pro.php?pro_id=155 I am receiving the usual telemetry including RSSI and the receiver pack voltage from the Bus but I am unable to get any of the unique telemetry messages that the Redundancy Bus...
by PNaz
Sun Jan 03, 2016 5:28 pm
Forum: er9x
Topic: No joy with 9x transmitter and SmartieParts SP Basic firmware programmer for Er9x install
Replies: 80
Views: 10517

Re: No joy with 9x transmitter and SmartieParts SP Basic firmware programmer for Er9x install

This is not a hardware issue with the mac. I went back to the mac with the transmitter I successfully programmed with the Win10 computer. It had the same failure to verify that i had previously. Win7 is installed on the mac through Parallels. I used eePe for Win7 on the mac. It successfully programm...
by PNaz
Sun Jan 03, 2016 2:56 pm
Forum: er9x
Topic: No joy with 9x transmitter and SmartieParts SP Basic firmware programmer for Er9x install
Replies: 80
Views: 10517

Re: No joy with 9x transmitter and SmartieParts SP Basic firmware programmer for Er9x install

Success for me as well. After reading about TT0002's problem with linux I tried using Win10 to flash the transmitter. I had been using my macbook and achieved partial success like he did with linux. With the Win10 computer I had absolutely no problems. The flash went well with no verification errors...
by PNaz
Sun Jan 03, 2016 2:57 am
Forum: er9x
Topic: No joy with 9x transmitter and SmartieParts SP Basic firmware programmer for Er9x install
Replies: 80
Views: 10517

Re: No joy with 9x transmitter and SmartieParts SP Basic firmware programmer for Er9x install

I have done some more troubleshooting of one of my M128a boards. I removed the SP Basic board, connected the transmitter back up, turned on the power and got "eprom error" and loud tone from the speaker. I then turned on the power while holding exit button and got the "restore" message. It looks lik...
by PNaz
Fri Jan 01, 2016 12:16 pm
Forum: er9x
Topic: No joy with 9x transmitter and SmartieParts SP Basic firmware programmer for Er9x install
Replies: 80
Views: 10517

Re: No joy with 9x transmitter and SmartieParts SP Basic firmware programmer for Er9x install

First attempt was on a Macbook OSX El Capitan with eePe Revision: 420, Aug 2 2015 and AvrDude 5.3.1. On the second transmitter I used a Win 10 Pro computer with eePe revision 419 Oct 25 2015 and AvrDude 5.1 so it was separate computers programming separate transmitters using separate USB cables with...
by PNaz
Thu Dec 31, 2015 11:50 pm
Forum: er9x
Topic: No joy with 9x transmitter and SmartieParts SP Basic firmware programmer for Er9x install
Replies: 80
Views: 10517

Re: No joy with 9x transmitter and SmartieParts SP Basic firmware programmer for Er9x install

I am having the same problem with the SP Basic. I have tried it on two separate transmitters with the same results. Both motherboards are new and have a 128A CPU installed. I did confirm before installing the SP Basic that they operated with the original Flysky firmware. After trying to read the fla...
by PNaz
Wed Nov 04, 2015 10:33 am
Forum: 9Xtreme upgrade board
Topic: Receive 9xtreme and Installation
Replies: 486
Views: 52940

Re: Receive 9xtreme and Installation

I have both a 9X Atmega 64 board and a 128 board available to do the 9Xtreme upgrade. Is there any advantage to using the 128? I can't see any advantage if the original 9X board is just used for I/O.

Paul
by PNaz
Tue Oct 27, 2015 11:19 pm
Forum: 9Xtreme upgrade board
Topic: Receive 9xtreme and Installation
Replies: 486
Views: 52940

Re: Receive 9xtreme and Installation

Steve I just received my 9Xtreme board via Swiss Post and Canada Post. I am down the valley from you in Kaleden 10km south of Penticton. It will be a good comparison of the shipping times versus the one you had shipped to yourself.

Paul Nazaroff
by PNaz
Thu Apr 23, 2015 7:45 am
Forum: erskyTx (was ersky9x)
Topic: ERSKY9X on Taranis
Replies: 474
Views: 66709

Re: ERSKY9X on Taranis

I have had the same copy problem for a while now on my Taranis. I assumed it was a problem with my timing of short press versus long press because sometimes I can switch models normally and sometimes it copies the previous model to the new model. I am currently using Ersky9x V.24-Mike 02.04.2015. It...
by PNaz
Mon Sep 08, 2014 3:52 pm
Forum: General help (FrSky Taranis radio)
Topic: Alerts when timer has gone past zero
Replies: 5
Views: 1402

Re: Alerts when timer has gone past zero

Ersky9x for Taranis continuously beeps for a minute after the timer reaches zero.

Paul
by PNaz
Sun Jul 13, 2014 9:29 am
Forum: erskyTx (was ersky9x)
Topic: ERSKY9X Coding
Replies: 4475
Views: 402930

Re: ERSKY9X Coding

I found a bug with the latest 11 July Test version for Taranis. It doesn't show the signal strength of the receiver or the SWR of the antenna. Both don't have any number showing. The transmitter is transmitting properly. Using the wonderful boot loader I reverted to my previous working version 30 Ju...
by PNaz
Thu Jul 10, 2014 12:32 am
Forum: Turnigy 9XR PRO radio
Topic: Little Tutorial-New Voice Alarms menu
Replies: 40
Views: 8370

Re: Little Tutorial-New Voice Alarms menu

João, your tutorial is excellent. There is absolutely no reason to apologize for your English skills. Your tutorial is organized well and thoroughly explained. I know you live and work in Germany so presumably you are fluent in German as well as your native Portuguese. I wish I could speak more than...
by PNaz
Fri Jun 27, 2014 4:58 pm
Forum: eepSKYe
Topic: eepSKYe
Replies: 710
Views: 124689

Re: eepSKYe

Mike, eepSkye 27 June for Taranis is now working properly with the custom switches. Now that it is working with Taranis I moved my Taranis models over to the Sky9x transmitter and have found a problem. The source in mixes is moved one selection off if the source is greater than P3. If the source is ...
by PNaz
Thu Jun 26, 2014 12:43 pm
Forum: erskyTx (was ersky9x)
Topic: ERSKY9X Coding
Replies: 4475
Views: 402930

Re: ERSKY9X Coding

Mike, I still have problems with latest test eepskye and Taranis. When an eeprom is read from the transmitter the AND switch in Switches is incremented by one if it is a custom switch. CS1 becomes CS2, etc. Physical switches are not affected. SA- stays as SA-. Burning the eeprom back to the transmit...
by PNaz
Wed Jun 25, 2014 3:18 pm
Forum: erskyTx (was ersky9x)
Topic: ERSKY9X Coding
Replies: 4475
Views: 402930

Re: ERSKY9X Coding

João, I agree with you. Mike's current endeavor to change the layout to a simpler and more logical setup is a great idea. I have tried openTX up to ver 2.0.3 and have given up on it. It's too confusing, complicated, and the general direction is to add more. I don't need the more complicated programm...
by PNaz
Wed Jun 25, 2014 1:48 pm
Forum: erskyTx (was ersky9x)
Topic: ERSKY9X Coding
Replies: 4475
Views: 402930

Re: ERSKY9X Coding

Mike. A problem with voice switches in eepskye. There is a total of 32 switches available. Default setting is for 0 voice switches but 8 switches are shown available. If I select for instance 16 voice switches than 24 are now available. The number of voice switches available are always 8 greater tha...

Go to advanced search