Search found 732 matches

by kalle123
Wed Jun 05, 2019 10:01 am
Forum: Hardware
Topic: Taranis X9DP - SD Card issue
Replies: 20
Views: 623

Re: Taranis X9DP - SD Card issue

jhsa wrote:
Wed Jun 05, 2019 9:56 am
I smell a bad card there :) or not properly formatted. Can you try another one?? ;)

João
andrewju wrote:
Tue Jun 04, 2019 8:48 pm
... and also tried all the microSD cards I had at hand (8Gb and up) - no luck...
:mrgreen:
by kalle123
Mon Jun 03, 2019 6:06 am
Forum: OpenXVario - an open source vario supported by the open source firmwares!!
Topic: getting sounds with vario on 9xr opentx 2.1.9
Replies: 2
Views: 134

Re: getting sounds with vario on 9xr opentx 2.1.9

Please check marked settings in your TX SETUP

Image

In TELEMETRY of your model

Image

and generate a sound output in SPECIAL FUNCTION.

(I put the sound on switch SD)

Image
by kalle123
Sun May 12, 2019 6:04 am
Forum: FRSky Horus radio
Topic: Adjusting gimbal tension Horus10s
Replies: 4
Views: 397

Re: Adjusting gimbal tension Horus10s

1.5 mm allen key.

Picture from Helle's German OpenTX manual (link to that manual can be found here in this forum)

viewtopic.php?f=92&t=3563&hilit=helle#p52110
Image

cu KH
by kalle123
Sat May 11, 2019 5:20 pm
Forum: FRSky Horus radio
Topic: Adjusting gimbal tension Horus10s
Replies: 4
Views: 397

Re: Adjusting gimbal tension Horus10s

What do you want?

The diameter of the screws or the size of the key for adjusting those screws?

cu KH
by kalle123
Wed May 01, 2019 9:21 am
Forum: Hardware
Topic: DIY Wireless sim dongle with XJT and X8R for 9XR Pro
Replies: 16
Views: 561

Re: DIY Wireless sim dongle with XJT and X8R for 9XR Pro

Just look for "RC simulator" at aliexpress, banggood, ebay ........

br
by kalle123
Sun Apr 28, 2019 5:46 am
Forum: OpenXVario - an open source vario supported by the open source firmwares!!
Topic: Brushless rpm sensor from esc output wires
Replies: 1
Views: 240

Re: Brushless rpm sensor from esc output wires

I use my DIY rpm sensor with oXs.

T6txMbWl.png.jpeg

The hobbywing rpm sensor also works fine.

Have a look at my German thread here ....

http://www.rc-network.de/forum/showthre ... hlight=rpm
by kalle123
Mon Apr 15, 2019 3:15 pm
Forum: General help (FrSky Taranis radio)
Topic: X9D - Stuttering Noise and no startup
Replies: 19
Views: 842

Re: X9D - Stuttering Noise and no startup

Seems there is not enough space on SD card. Will have to buy bigger one for that... Take the SD card from the Taranis. Backup the card content on your computer. Read and follow the procedure here https://oscarliang.com/flash-opentx-firmware-taranis/ A 1GB SD card is totally sufficient for use. br
by kalle123
Fri Apr 12, 2019 6:15 am
Forum: OpenXVario - an open source vario supported by the open source firmwares!!
Topic: current sensor help...ACS712
Replies: 4
Views: 404

Re: current sensor help...ACS712

Have a look here

https://www.helifreak.com/showthread.php?t=758263

He is using an ACS 758, but ACS 712 should be wired in the same way.
by kalle123
Wed Apr 10, 2019 8:40 pm
Forum: OpenXVario - an open source vario supported by the open source firmwares!!
Topic: VFAS not displayed. openTX 2.2.3/oXs 8.2/FrSky RX6R
Replies: 2
Views: 224

Re: VFAS not displayed. openTX 2.2.3/oXs 8.2/FrSky RX6R

Found it!

Think, I got out of practice :)

I have current on A0 and VFAS on A1.

Code: Select all

#define PIN_VOLTAGE        1  , 8     , 8   , 8    , 8   , 8
...
#define PIN_CURRENTSENSOR   0
So A1 -> VOLT_1, not VOLT_2. That was my mistake.

Sorry, but as always, it helps, to put things aside for a while ....
by kalle123
Wed Apr 10, 2019 6:11 pm
Forum: OpenXVario - an open source vario supported by the open source firmwares!!
Topic: VFAS not displayed. openTX 2.2.3/oXs 8.2/FrSky RX6R
Replies: 2
Views: 224

VFAS not displayed. openTX 2.2.3/oXs 8.2/FrSky RX6R

Today tried to convert one of my oXs sensors from oXs v7.0 to v8.2 for use with a another (not mine) Taranis (openTX 2.2.3). Sensor has MS5611, ACS712 on A0 and Lipo voltage to A1. Vario and current working, but have an issue with the voltage. For my understanding, this (in oXs_config_basic.h) // **...
by kalle123
Thu Mar 21, 2019 7:22 am
Forum: OpenXVario - an open source vario supported by the open source firmwares!!
Topic: smallest openxsensor vario
Replies: 3
Views: 896

Re: smallest openxsensor vario

Just found this here

http://www.rc-network.de/forum/showthre ... ost4759522

Vario and current.

I miss a crystal and a simple way to flash the firmware.

br KH
by kalle123
Tue Feb 19, 2019 7:24 am
Forum: Turnigy 9XR radio
Topic: 9XR, openlrs and Telemetry
Replies: 10
Views: 774

Re: 9XR, openlrs and Telemetry

Another German with handheld tx ;)
by kalle123
Mon Oct 08, 2018 6:13 am
Forum: OpenXVario - an open source vario supported by the open source firmwares!!
Topic: Creating an RPM and Temp Sensor
Replies: 53
Views: 12873

Re: Creating an RPM and Temp Sensor

This rpm sensor also works well.

Small and cheap .....

Image
by kalle123
Sat Oct 06, 2018 12:49 pm
Forum: OpenXVario - an open source vario supported by the open source firmwares!!
Topic: OpenXSensor 2 batteries with 2 cells voltage problem
Replies: 8
Views: 778

Re: OpenXSensor 2 batteries with 2 cells voltage problem

mstrens wrote:
Sat Oct 06, 2018 11:34 am
Otherwise, as said before you can use 2 oXs with different ID.
With all protocols? "FRSKY_SPORT , FRSKY_HUB , FRSKY_SPORT_HUB , MULTIPLEX , HOTT; JETI"

That would be new, at least for me. ;)

Therefore I asked for the hardware, he is using.

br
by kalle123
Fri Oct 05, 2018 5:44 am
Forum: OpenXVario - an open source vario supported by the open source firmwares!!
Topic: OpenXSensor 2 batteries with 2 cells voltage problem
Replies: 8
Views: 778

Re: OpenXSensor 2 batteries with 2 cells voltage problem

A bit more information is needed.

Please make a drawing of the wiring, you plan to use.

And what hardware (RX - TX) are you using?

But, as Dean says, I would also go for two oXs sensors.

br
by kalle123
Mon Oct 01, 2018 4:22 pm
Forum: OpenXVario - an open source vario supported by the open source firmwares!!
Topic: OpenXsensor Configurator
Replies: 195
Views: 45954

Re: OpenXsensor Configurator

So no use to cheer you up, then.

But João, I am used to do the configuration in the config file, but I hate it being split up in basic and advanced ;)

br KH
by kalle123
Mon Oct 01, 2018 8:37 am
Forum: OpenXVario - an open source vario supported by the open source firmwares!!
Topic: OpenXsensor Configurator
Replies: 195
Views: 45954

Re: OpenXsensor Configurator

Mike, that is, what I found here.

Might have a look. It was written in java ...

br KH
by kalle123
Mon Oct 01, 2018 6:37 am
Forum: OpenXVario - an open source vario supported by the open source firmwares!!
Topic: OpenXsensor Configurator
Replies: 195
Views: 45954

Re: OpenXsensor Configurator

Hi João.

Found a copy and it is still working ... :lol:

I bit obsolete, but never mind.

Image
by kalle123
Mon Oct 01, 2018 5:42 am
Forum: OpenXVario - an open source vario supported by the open source firmwares!!
Topic: OpenXsensor Configurator
Replies: 195
Views: 45954

Re: OpenXsensor Configurator

jhsa wrote:
Sun Sep 30, 2018 9:22 pm
Still, it is really a shame. I did love this tool :(

João
Get used to
... edit manually the 2 files oXs_config_basic.h and oXs_config_advanced.h
You will love that way too ;)

br KH (who could search on backup HDDs here for a copy of that Configurator and post it here :mrgreen: )
by kalle123
Thu Sep 27, 2018 2:05 pm
Forum: General help (FrSky Taranis radio)
Topic: D8R II plus in PPM mode
Replies: 13
Views: 1431

Re: D8R II plus in PPM mode

Ray, have those two here and both work fine. ;)

Image

br
by kalle123
Thu Sep 27, 2018 5:45 am
Forum: General help (FrSky Taranis radio)
Topic: D8R II plus in PPM mode
Replies: 13
Views: 1431

Re: D8R II plus in PPM mode

Raythegreat wrote:
Wed Sep 26, 2018 8:56 pm
RS-232 on PC's is very rare now.
I know, my PC still has one. But Ray, those also work and don't cost much.

https://de.aliexpress.com/wholesale?cat ... 32+adapter

Good to have one in the box, just in case.

br
by kalle123
Mon Sep 24, 2018 9:06 pm
Forum: General help (FrSky Taranis radio)
Topic: D8R II plus in PPM mode
Replies: 13
Views: 1431

Re: D8R II plus in PPM mode

Ray, flashing the D8R II without having the FrSky adapter at hand is not impossible. Two ways With an FTDI adapter https://oscarliang.com/flash-frsky-rx-firmware/ or if your computer still has an COM port https://www.rcgroups.com/forums/showthread.php?1866014-Simple-FrSKY-Receiver-Flash-How-To-with-...
by kalle123
Mon Sep 24, 2018 3:07 pm
Forum: OpenXVario - an open source vario supported by the open source firmwares!!
Topic: GPS & Arduino Pro mini
Replies: 30
Views: 2043

Re: GPS & Arduino Pro mini

Good to hear it is solved .....
by kalle123
Mon Sep 24, 2018 6:58 am
Forum: openTx
Topic: Unable upgrade to 2.2.2 on LinuxMint due to dependency error
Replies: 7
Views: 806

Re: Unable upgrade to 2.2.2 on LinuxMint due to dependency error

I am running Mint 18.03 But of course I ran sudo apt-get update and sudo apt-get upgrade so I should have the latest packages that the Mint distro provides. Perhaps I can add the package manually if I can find it. Any ideas? Thanks! Have LM 18.03 Xfce here. Same issue. But it works with LM 19. Thos...
by kalle123
Mon Sep 24, 2018 5:50 am
Forum: General help (FrSky Taranis radio)
Topic: D8R II plus in PPM mode
Replies: 13
Views: 1431

Re: D8R II plus in PPM mode

Same hardware (D8R II and D8R-XP), different firmware and a different sticker on the housing.

br
by kalle123
Mon Sep 24, 2018 5:47 am
Forum: OpenXVario - an open source vario supported by the open source firmwares!!
Topic: GPS & Arduino Pro mini
Replies: 30
Views: 2043

Re: GPS & Arduino Pro mini

With latest version of oXs I can set "Arduino measures voltage" to NO here and only activate GPS. Don't see an error when compiling.

Please post your oXs_config_basic.h and oXs_config_advanced.h

br
by kalle123
Mon Sep 03, 2018 9:58 am
Forum: openTx
Topic: Taranis X9D migrating 2.0 to 2.1/2.2 impact?
Replies: 13
Views: 1076

Re: Taranis X9D migrating 2.0 to 2.1/2.2 impact?

@Bob. I bit off topic, but ... I use erSky9x firmware on my Taranis and eepSkye on my PC. On http://www.er9x.com/ I see http://imgur.com/fb0emwUl.png those Linux packages. Nice, would like to give it a try, BUT those are 386 deb packages!! We are in 2018 and who is still on a 386 system? br KH
by kalle123
Wed May 23, 2018 1:02 pm
Forum: openTx
Topic: Firmware not loading to Taranis ?
Replies: 31
Views: 2769

Re: Firmware not loading to Taranis ?

Please, more information. Can you read data from your Taranis to Companion?
by kalle123
Fri May 18, 2018 10:02 am
Forum: openTx
Topic: Program Mega2560 via USB - how to?
Replies: 3
Views: 801

Re: Program Mega2560 via USB - how to?

Are you trying to use the Mega as normal Arduino or do you want to use it with openTX? #1. case just flash the bootloader with the Arduino IDE #2. case Download from here https://github.com/Ingwie/NextStepRc-2.18 then ... (if I recall right ;) ) 1. Arduino fuses flash (usbasp ISP) "mega2560_usbasp_f...

Go to advanced search