Search found 16641 matches

by MikeB
Mon Oct 03, 2022 2:28 pm
Forum: openTx
Topic: Taranis -X9D+ and OrangeRX ver 2.1 module
Replies: 0
Views: 24

Taranis -X9D+ and OrangeRX ver 2.1 module

Posted from a PM sent to me: I hope this might be the right place to ask this question. I have Taranis -X9D+ and OrangeRX module, and can not bind a UMX Radian. I am using OpenTX companion and just can not to get it all to bind. Really could use you help, PLEASE! Please find picture of what I have ...
by MikeB
Mon Oct 03, 2022 2:24 pm
Forum: ersky9xr
Topic: How to load ELRSv2.bas in Turnigy 9XR PRO?
Replies: 2
Views: 50

Re: How to load ELRSv2.bas in Turnigy 9XR PRO?

Create a "Scripts" directory in the root of the SD card, then put the .bas file in there.

Mike
by MikeB
Sat Sep 24, 2022 3:16 pm
Forum: er9x / gruvin9x / th9 based firmwares
Topic: ersky tx 9xr-Pro revision 222 to revision 223
Replies: 4
Views: 411

Re: ersky tx 9xr-Pro revision 222 to revision 223

Here is the list. Many changes are adding support for new radios with large, colour screens. Logical switch enhancements and support for additions to the multiprotocol module are the main changes for all radios. Add support for: T18, TX16S X10Express X10 hall sticks support RM-TX16 handle bad rotary...
by MikeB
Fri Sep 23, 2022 6:16 pm
Forum: er9x / gruvin9x / th9 based firmwares
Topic: ersky tx 9xr-Pro revision 222 to revision 223
Replies: 4
Views: 411

Re: ersky tx 9xr-Pro revision 222 to revision 223

I'm working on a list for you, just need a bit of time to complete it.

Mike
by MikeB
Tue Sep 20, 2022 2:57 pm
Forum: Turnigy 9XR PRO radio
Topic: 9XR Pro with XJT - Firmware Updates?
Replies: 7
Views: 791

Re: 9XR Pro with XJT - Firmware Updates?

Go here: viewtopic.php?f=122&t=5575
and look at the file: 9XR Pro Using SAM-BA to restore bricked Tx 2014-02-12.pdf

This should get you radio back working.

I was asking you to try connecting the radio to your computer and see if it is detected.

Mike
by MikeB
Tue Sep 20, 2022 9:32 am
Forum: Turnigy 9XR PRO radio
Topic: 9XR Pro with XJT - Firmware Updates?
Replies: 7
Views: 791

Re: 9XR Pro with XJT - Firmware Updates?

The update to the XJT might take 2 or 3 minutes.

If you plug in the USB with power off, then turn power on, do you get any USB device appearing on the computer?

Mike
by MikeB
Sun Sep 18, 2022 2:02 pm
Forum: ersky9xr
Topic: XJT with X4R & FLVS s.port telemetry
Replies: 14
Views: 713

Re: XJT with X4R & FLVS s.port telemetry

Test version posted on the test versions thread, first post.
It may even handle all 8 cells!
I don't have a new FLVS so can't test that.

Mike
by MikeB
Fri Sep 16, 2022 10:19 am
Forum: ersky9xr
Topic: XJT with X4R & FLVS s.port telemetry
Replies: 14
Views: 713

Re: XJT with X4R & FLVS s.port telemetry

OK, I now know what the problem is. I'll fix it in the next day or so.

Mike
by MikeB
Thu Sep 15, 2022 6:46 pm
Forum: ersky9xr
Topic: XJT with X4R & FLVS s.port telemetry
Replies: 14
Views: 713

Re: XJT with X4R & FLVS s.port telemetry

OK, so this is the "new" FLVS-ADV that supports up to 8 cells. I've just checked r223 with an older FLVSS and this works OK. To help find why r223 isn't showing this sensor, a "Raw Log File" would be useful to me (see this post: https://openrcforums.com/forum/viewtopic.php?f=84&t=13859&p=156269&hili...
by MikeB
Thu Sep 15, 2022 10:30 am
Forum: ersky9xr
Topic: XJT with X4R & FLVS s.port telemetry
Replies: 14
Views: 713

Re: XJT with X4R & FLVS s.port telemetry

Here is r222 for the 9XR-PRO. Perhaps you could try this to help locate when the problem started.

Mike
by MikeB
Tue Sep 13, 2022 4:31 pm
Forum: ersky9xr
Topic: XJT with X4R & FLVS s.port telemetry
Replies: 14
Views: 713

Re: XJT with X4R & FLVS s.port telemetry

UsrProto should be FrSky (not FrHub). What is the LED on the FLVSS doing? What is the display on the FLVSS showing? Do you have a module installed internally? If not I suggest disabling the internal module, you probably don't need it enabled anyway unless you are using both modules at the same time!...
by MikeB
Tue Sep 13, 2022 2:21 pm
Forum: ersky9xr
Topic: XJT with X4R & FLVS s.port telemetry
Replies: 14
Views: 713

Re: XJT with X4R & FLVS s.port telemetry

Have you set the protocol to "XJT"?

Mike
by MikeB
Thu Sep 08, 2022 8:25 am
Forum: The Pickled Gnu (The Pub)
Topic: Winged Shadow Systems has discontinued its product line
Replies: 11
Views: 4613

Re: Winged Shadow Systems has discontinued its product line

Support is still in erskyTx!
Another possible solution might be to program an Arduino Mini that then sits between the WSHH and the Rx and translates the data into FrSky format.

Mike
by MikeB
Tue Sep 06, 2022 10:09 pm
Forum: The Pickled Gnu (The Pub)
Topic: Winged Shadow Systems has discontinued its product line
Replies: 11
Views: 4613

Re: Winged Shadow Systems has discontinued its product line

D8 telemetry data is processed in "frsky_d.cpp". User data is processed in:
void parseTelemHubByte(uint8_t byte)
It looks like only FrSky sensors are processed, and no data is passed to scripts!

Mike
by MikeB
Tue Sep 06, 2022 11:26 am
Forum: The Pickled Gnu (The Pub)
Topic: Winged Shadow Systems has discontinued its product line
Replies: 11
Views: 4613

Re: Winged Shadow Systems has discontinued its product line

For D8 receivers, do a search for "frsky Two-way system protocol", and you should get several hits for a PDF file describing the protocol sent to the Tx. When I implemented support for the WS How High, it was sending 2 bytes of height data, with a repeat rate slower than 100mS between data. The byte...
by MikeB
Sat Sep 03, 2022 2:40 pm
Forum: The Pickled Gnu (The Pub)
Topic: Winged Shadow Systems has discontinued its product line
Replies: 11
Views: 4613

Re: Winged Shadow Systems has discontinued its product line

I've kept support for the WS How High in er9x/erskyTx, I believe support was removed from openTx. I don't know if this support handles a How High RT, I don't know what the RT means! erskyTx is available for the Jumper T12, I don't know if the RM TX12 is sufficiently the same that it will run on that...
by MikeB
Fri Sep 02, 2022 9:00 pm
Forum: ersky9xr
Topic: Receiver signal critical warning on model power up
Replies: 1
Views: 242

Re: Receiver signal critical warning on model power up

There is some averaging done in both the Rx and Tx for the RSSI signal. It is very likely one or both doesn't have enough time, at power up, to get a full average so gives a low reading to start with. As long as you get a good reading after that, you may safely ignore the initial warning. The XJT mo...
by MikeB
Wed Aug 31, 2022 11:28 am
Forum: er9x / gruvin9x / th9 based firmwares
Topic: Notes on programing
Replies: 1
Views: 510

Re: Notes on programing

Have you seen the er9x manual (from this thread: viewtopic.php?f=5&t=6473)?

Mike
by MikeB
Mon Aug 29, 2022 8:11 am
Forum: ersky9xr
Topic: Model Specific Binding??
Replies: 2
Views: 258

Re: Model Specific Binding??

With a XJT module you may select D16 or D8 from the menu, so you would not need to change the DIP switches (you use "XJT" protocol not PPM with the XJT).
D8 protocol does not support "model specific binding" but D16 does (called RxNum in the menu).

Mike
by MikeB
Sat Aug 27, 2022 8:08 pm
Forum: ersky9xr
Topic: 9xr Pro ELRS?
Replies: 1
Views: 160

Re: 9xr Pro ELRS?

I believe it should work, just select "XFIRE" as the protocol for the external module (assuming the module fits mechanically).

Mike
by MikeB
Wed Aug 24, 2022 10:52 am
Forum: er9x model setup
Topic: Turnigy 9X running ER9X setup to run a tank, how?
Replies: 10
Views: 1060

Re: Turnigy 9X running ER9X setup to run a tank, how?

Try: CH1: 100% Rud Curve(x<0) * 100% Ele (MULTIPLY multiplex) + 100% Ele CH2: 100% Rud Curve(x>0) * 100% Ele (MULTIPLY multiplex) - 100% Ele (no channel reversing). I've just changed the sign of Rud and the last Ele in channel 2. I still don't understand why reversing just one channel didn't, at lea...
by MikeB
Wed Aug 24, 2022 8:57 am
Forum: er9x model setup
Topic: Turnigy 9X running ER9X setup to run a tank, how?
Replies: 10
Views: 1060

Re: Turnigy 9X running ER9X setup to run a tank, how?

Edited to show CH2 !
You probably need to reverse one of the channels (in the limits menu).

Mike
by MikeB
Tue Aug 23, 2022 8:07 pm
Forum: er9x model setup
Topic: Turnigy 9X running ER9X setup to run a tank, how?
Replies: 10
Views: 1060

Re: Turnigy 9X running ER9X setup to run a tank, how?

CH1: 100% Rud Curve(x<0)
* 100% Ele (MULTIPLY multiplex)
+ 100% Ele
CH2: -100% Rud Curve(x>0)
* 100% Ele (MULTIPLY multiplex)
+ 100% Ele

looks to work. You get +/- 100% forwards and backwards and as you move the Rud stick, the track in the Rud direction gets reduced to zero.

Mike
by MikeB
Tue Aug 23, 2022 2:29 pm
Forum: er9x model setup
Topic: Turnigy 9X running ER9X setup to run a tank, how?
Replies: 10
Views: 1060

Re: Turnigy 9X running ER9X setup to run a tank, how?

Several ways of doing this, this seems to work: CH1: 50% Rud * 100% Ele (MULTIPLY multiplex) + 50% Ele CH2: -50% Rud * 100% Ele (MULTIPLY multiplex) + 50% Ele You may need to reverse one or both outputs (in limits menu). As with your mixes, the Ele stick changes the speed of the tracks up to 50%. As...
by MikeB
Sun Aug 21, 2022 8:45 pm
Forum: openTx
Topic: 2nd RC, 1st OpenTX
Replies: 63
Views: 3078

Re: 2nd RC, 1st OpenTX

The G means you have selected a global variable to be used for the weight.
Try holding the ENTER button in for a long time, this may toggle between a number and a G value (I don't use openTx so I'm guessing this is how to swap them).

Mike
by MikeB
Sat Aug 20, 2022 12:04 pm
Forum: erskyTx (was ersky9x)
Topic: ERSKYTx (was ersky9x) Questions
Replies: 2290
Views: 953077

Re: ERSKYTx (was ersky9x) Questions

1. For the FrSky modules (the only ones returning a SWR value as far as I know) this is available on some of the fixed telemetry screens and may be selected for display on a custom telemetry screen (The TSSI value changes to SWR when a FrSky module is selected). 2. The MPM firmware version should ap...
by MikeB
Mon Aug 01, 2022 9:20 am
Forum: Turnigy 9XR PRO radio
Topic: My Turnigy 9xr pro can not boost!!!
Replies: 4
Views: 1005

Re: My Turnigy 9xr pro can not boost!!!

Check pin 4 of J6, this should also have the battery voltage on it. It is the RF module power, switched from a separate contact on the power switch, and is used to detect the power switch is on.

Mike
by MikeB
Mon Aug 01, 2022 9:14 am
Forum: Software
Topic: Voltage Sensor no longer reading
Replies: 10
Views: 2142

Re: Voltage Sensor no longer reading

It does sound like there is something now wrong with the XJT. Maybe worth checking the 5-way connector in the XJT.
The SPort signal is also available as a 3-pin connector on the exposed face of the XJT.

Mike
by MikeB
Mon Aug 01, 2022 9:10 am
Forum: Turnigy 9XR PRO radio
Topic: 9XR Pro with XJT - Firmware Updates?
Replies: 7
Views: 791

Re: 9XR Pro with XJT - Firmware Updates?

What version of erskyTx do you have installed (Radio Setup|Version menu)?

When you plug the USB into the radio, make sure you push quite hard. The connector on the 'PRO has a very positive "click" when the USB connector becomes fully in place.

Mike
by MikeB
Mon Jul 25, 2022 8:36 am
Forum: 9Xtreme upgrade board
Topic: Problem with last new Hobbyking Turnigy 9X transmiters.
Replies: 189
Views: 116643

Re: Problem with last new Hobbyking Turnigy 9X transmiters.

This is the firmware that is flashed to the AVR processor (same for '64 and '128).

Mike

Go to advanced search