Hi,
I have no experience in doing this but I can point you to some info:
Go to this thread. At the end ot the first post you'll find a PDF which shows you how to restore the firmware.
And in this post you'll find a ZIP with all files you will need.
Klaus
Search found 553 matches
- Sun Nov 18, 2018 4:23 pm
- Forum: Hardware
- Topic: 9xr pro total shot down
- Replies: 7
- Views: 6402
- Mon May 28, 2018 4:53 pm
- Forum: er9x
- Topic: schleppgas für verbrenner heli
- Replies: 2
- Views: 3839
Re: schleppgas für verbrenner heli
Hallo phil, das ist eine typische Aufgabe für die logischen Schalter. Schalter L1 vergleicht P1 und THR. Wenn THR kleiner als P1 dann ist L1=ON ansonsten OFF Switches.jpg Hier mal ein Beispiel mit Gasausgabe auf Channel 5: 1. Zeile: Channel 5: Channel 5 gibt normalerweise den Wert von P1 aus 2. Zeil...
- Tue Mar 27, 2018 9:08 pm
- Forum: er9x / gruvin9x / th9 based firmwares
- Topic: Nano QX setup
- Replies: 12
- Views: 19282
Re: Nano QX setup
Please try limits of 80% on every channel as 100% on ersky9x equals to 125% on spektrum radios
depending on the used TX module.
Maybe a throw of 100% is too much for your nanoQX.
I'm not shure but it may be that changing mode only works in a specific range of throttle ...
depending on the used TX module.
Maybe a throw of 100% is too much for your nanoQX.
I'm not shure but it may be that changing mode only works in a specific range of throttle ...
- Tue Mar 27, 2018 4:52 pm
- Forum: er9x / gruvin9x / th9 based firmwares
- Topic: Nano QX setup
- Replies: 12
- Views: 19282
Re: Nano QX setup
Here is the model file I use on my 9XR-Pro ...
Klaus- Sun Oct 15, 2017 7:30 pm
- Forum: erskyTx (was ersky9x)
- Topic: ERSKY9X Coding
- Replies: 4540
- Views: 1970645
Re: ERSKY9X Coding
Thank you, Mike
Klaus
Klaus
- Sun Oct 15, 2017 7:20 pm
- Forum: erskyTx (was ersky9x)
- Topic: ERSKY9X Coding
- Replies: 4540
- Views: 1970645
Re: ERSKY9X Coding
Do you have some centre beeps activated?
Without, nothing to blink.
Without, nothing to blink.
- Sun Oct 15, 2017 7:18 pm
- Forum: erskyTx (was ersky9x)
- Topic: ERSKY9X Coding
- Replies: 4540
- Views: 1970645
Re: ERSKY9X Coding
Version
Video - Sun Oct 15, 2017 6:09 pm
- Forum: erskyTx (was ersky9x)
- Topic: ERSKY9X Coding
- Replies: 4540
- Views: 1970645
Re: ERSKY9X Coding
Murphy strikes ...
At the moment I have 2 Pros and 3 9XT at hand
and all 5 show this behaviour ...
Klaus
At the moment I have 2 Pros and 3 9XT at hand
and all 5 show this behaviour ...
Klaus
- Sun Oct 15, 2017 5:47 pm
- Forum: erskyTx (was ersky9x)
- Topic: ERSKY9X Coding
- Replies: 4540
- Views: 1970645
Re: ERSKY9X Coding
Hi Mike,
in f2 for Pro and 9XT I noticed a little beauty mistake:
In "Model Setup" - "General"
while setting "Volume Control"
the highlighted parts of "Beep Cnt" are also blinking.
Klaus
in f2 for Pro and 9XT I noticed a little beauty mistake:
In "Model Setup" - "General"
while setting "Volume Control"
the highlighted parts of "Beep Cnt" are also blinking.
Klaus
- Sun Oct 15, 2017 11:08 am
- Forum: erskyTx (was ersky9x)
- Topic: ERSKY9X Coding
- Replies: 4540
- Views: 1970645
- Sun Oct 15, 2017 9:34 am
- Forum: erskyTx (was ersky9x)
- Topic: ERSKY9X Coding
- Replies: 4540
- Views: 1970645
Re: ERSKY9X Coding
Thank you in advance.
Klaus
Klaus
- Sat Oct 14, 2017 11:15 pm
- Forum: erskyTx (was ersky9x)
- Topic: ERSKY9X Coding
- Replies: 4540
- Views: 1970645
Re: ERSKY9X Coding
Hi Mike,
I updated both my 9XR Pro and 9Xtreme to f2.
On the Pro I found a very nice option to calibrate pots with detent,
but I can't find this option on 9Xtreme. Is this intended?
Klaus
I updated both my 9XR Pro and 9Xtreme to f2.
On the Pro I found a very nice option to calibrate pots with detent,
but I can't find this option on 9Xtreme. Is this intended?
Klaus
- Sun May 28, 2017 6:36 pm
- Forum: General Information & Rules
- Topic: Subscribe or Bookmark
- Replies: 1
- Views: 7053
Re: Subscribe or Bookmark
Please click on the wrench symbol at page bottom (or top) ...
Klaus
Klaus
- Sat May 20, 2017 3:10 pm
- Forum: Hardware
- Topic: having issues with USBASP driver
- Replies: 55
- Views: 29886
Re: having issues with USBASP driver
Don't know what to hell is all the fuss about. I have several Win10 systems (pro, 64) here and no problems with usbasp. Drivers installed via Zadig. Only downside I found is this: Arduino IDE (1.6.10) (with avrdude 6.3) only works with WinUSB drivers provided e.g. by Zadig (2.2). But avrdude 5.1 pro...
- Sat Apr 29, 2017 10:00 am
- Forum: Hardware
- Topic: Noob Confusion with 9X Calibration and trim Display
- Replies: 5
- Views: 4916
Re: Noob Confusion with 9X Calibration and trim Display
What does the 'DiagAna' screen in the radio setup show for the sticks?
Did you create a new model?
If not: What about the 'sub trim' in the limits menu?
Klaus
Did you create a new model?
If not: What about the 'sub trim' in the limits menu?
Klaus
- Tue Apr 25, 2017 4:47 pm
- Forum: ersky9xr
- Topic: RESOLVED: Template does not setup mixes using TAER order?
- Replies: 70
- Views: 44099
Re: Template does not setup mixes using TAER order?
Maybe I'm a bit goofy here but I don't understand what you mean with ELE and PITCH Servo. This names belong to mechanical mixing where you indeed have separate servos for pitch, nick and roll. But nevertheless: If you used the template the swash type is set to '120'. For this the rear servo should b...
- Tue Apr 18, 2017 8:15 pm
- Forum: ersky9xr
- Topic: RESOLVED: Template does not setup mixes using TAER order?
- Replies: 70
- Views: 44099
Re: Template does not setup mixes using TAER order?
Why does it not set up the correct TAER order making my throttle ch1, etc? TAER is not applicable to heli mode. A CCPM flybar heli doesn't have regular aileron or elevator!! :shock: You have 3 servos to tilt (cyclic pitch) or lift (collective pitch) the swash plate. Usually ch1 to ch3 are the so ca...
- Wed Mar 22, 2017 7:38 pm
- Forum: erskyTx (was ersky9x)
- Topic: ERSKY9X Coding
- Replies: 4540
- Views: 1970645
Re: ERSKY9X Coding
Thanks in advance
Klaus
Klaus
- Wed Mar 22, 2017 6:39 pm
- Forum: erskyTx (was ersky9x)
- Topic: ERSKY9X Coding
- Replies: 4540
- Views: 1970645
Re: ERSKY9X Coding
I think you'll have to wait 'til Mike is able to provide his changes to pascal/midelic
PS: though I have some modules from bangood they don't have bind button and dial switch.
I removed them for some other projects.
Klaus
PS: though I have some modules from bangood they don't have bind button and dial switch.
I removed them for some other projects.
Klaus
- Wed Mar 22, 2017 6:07 pm
- Forum: erskyTx (was ersky9x)
- Topic: ERSKY9X Coding
- Replies: 4540
- Views: 1970645
- Wed Mar 22, 2017 3:30 pm
- Forum: erskyTx (was ersky9x)
- Topic: ERSKY9X Coding
- Replies: 4540
- Views: 1970645
Re: ERSKY9X Coding
Hi João,
in the docs on github under "not for the fainthearted"
See here
But I did't had time to test it yet.
Klaus
in the docs on github under "not for the fainthearted"
See here
But I did't had time to test it yet.
Klaus
- Tue Mar 21, 2017 6:22 pm
- Forum: erskyTx (was ersky9x)
- Topic: ERSKY9X Coding
- Replies: 4540
- Views: 1970645
Re: ERSKY9X Coding
Hi Mike,
problem solved. I was just too blind to find it in the docs ...
Klaus
problem solved. I was just too blind to find it in the docs ...
Klaus
- Tue Mar 21, 2017 4:22 pm
- Forum: erskyTx (was ersky9x)
- Topic: ERSKY9X Coding
- Replies: 4540
- Views: 1970645
Re: ERSKY9X Coding
Hi Mike,
which bootloader are you using for the multi?
Or can you please provide a HEX-File?
Klaus
which bootloader are you using for the multi?
Or can you please provide a HEX-File?
Klaus
- Tue Feb 28, 2017 10:34 pm
- Forum: er9x
- Topic: Replace the 9x motherboard, but can't flash er9x?
- Replies: 39
- Views: 20927
Re: Replace the 9x motherboard, but can't flash er9x?
I suspect your new motherboard is equipped with an Atmega128,
not with an Atmega64.
So you have to flash er9x-128.hex
and NEVER EVER use option -F
you may brick the Atmel.
Klaus
not with an Atmega64.
So you have to flash er9x-128.hex
and NEVER EVER use option -F
you may brick the Atmel.
Klaus
- Sat Feb 25, 2017 8:42 am
- Forum: erskyTx (was ersky9x)
- Topic: ERSKYTx (was ersky9x) Questions
- Replies: 2347
- Views: 1346180
Re: ERSKY9x Questions
To the root you have to put it ...
- Sun Feb 12, 2017 10:43 am
- Forum: 9Xtreme upgrade board
- Topic: Dead 9Xtreme
- Replies: 19
- Views: 18210
Re: Dead 9Xtreme
If you decide to desolder the STM with ChipQuick please be careful. There is some 'chickenfood' very close to it (disappears very quickly :) ). I therefore decided to cut each leg of the STM with an xacto-knife and desolder 'em one by one. But there you have the risk to rip off a track together with...
- Thu Jan 26, 2017 2:57 pm
- Forum: erskyTx (was ersky9x)
- Topic: ERSKY9X Coding
- Replies: 4540
- Views: 1970645
Re: ERSKY9X Coding
The new protocols menu looks fantastic.
A lot easier to work with.
Klaus
A lot easier to work with.
Klaus
- Thu Jan 26, 2017 9:33 am
- Forum: erskyTx (was ersky9x)
- Topic: ERSKY9X Coding
- Replies: 4540
- Views: 1970645
Re: ERSKY9X Coding
Hi Mike,
while trying to save the eeprom content of my revived 9XT I found a problem with eepskye.
Since rev 421, Nov. 10 2016 eepskye shows only 32 models for the 9XT while the 9XT itself handles 60 models.
Rev. 421, Juli 31 2016 however did handle 60 models.
Klaus
while trying to save the eeprom content of my revived 9XT I found a problem with eepskye.
Since rev 421, Nov. 10 2016 eepskye shows only 32 models for the 9XT while the 9XT itself handles 60 models.
Rev. 421, Juli 31 2016 however did handle 60 models.
Klaus
- Wed Jan 25, 2017 6:46 pm
- Forum: 9Xtreme upgrade board
- Topic: Burned USB port by cross linked cable - DONE
- Replies: 16
- Views: 15822
Re: Burned USB port by cross linked cable
YEAH HA, I'm (or better: the 9XT is) back in business.
Hopefully I will never have to solder parts with such a small pin pitch in the future
Thank you Mike!
Hopefully I will never have to solder parts with such a small pin pitch in the future
Thank you Mike!
- Wed Jan 25, 2017 5:55 pm
- Forum: 9Xtreme upgrade board
- Topic: Burned USB port by cross linked cable - DONE
- Replies: 16
- Views: 15822
Re: Burned USB port by cross linked cable
Hi Mike, I can see light at the end of the tunnel (or is it a train coming? ;) ). The STM is transplanted and DfuSeDemo recognizes it as STM Device in DFU mode, vendor 0483, productID DF11, version 2200. Can the .dfu file be converted from a .bin file or can you please share the .dfu file you mentio...