Search found 553 matches

by KAL
Sun Nov 18, 2018 4:23 pm
Forum: Hardware
Topic: 9xr pro total shot down
Replies: 7
Views: 6366

Re: 9xr pro total shot down

Hi,
I have no experience in doing this but I can point you to some info:
Go to this thread. At the end ot the first post you'll find a PDF which shows you how to restore the firmware.
And in this post you'll find a ZIP with all files you will need.

Klaus
by KAL
Mon May 28, 2018 4:53 pm
Forum: er9x
Topic: schleppgas für verbrenner heli
Replies: 2
Views: 3811

Re: schleppgas für verbrenner heli

Hallo phil, das ist eine typische Aufgabe für die logischen Schalter. Schalter L1 vergleicht P1 und THR. Wenn THR kleiner als P1 dann ist L1=ON ansonsten OFF Switches.jpg Hier mal ein Beispiel mit Gasausgabe auf Channel 5: 1. Zeile: Channel 5: Channel 5 gibt normalerweise den Wert von P1 aus 2. Zeil...
by KAL
Tue Mar 27, 2018 9:08 pm
Forum: er9x / gruvin9x / th9 based firmwares
Topic: Nano QX setup
Replies: 12
Views: 18513

Re: Nano QX setup

Please try limits of 80% on every channel as 100% on ersky9x equals to 125% on spektrum radios
depending on the used TX module.
Maybe a throw of 100% is too much for your nanoQX.
I'm not shure but it may be that changing mode only works in a specific range of throttle ...
by KAL
Tue Mar 27, 2018 4:52 pm
Forum: er9x / gruvin9x / th9 based firmwares
Topic: Nano QX setup
Replies: 12
Views: 18513

Re: Nano QX setup

Here is the model file I use on my 9XR-Pro ...
nano QX.eepm
(4.12 KiB) Downloaded 675 times
Klaus
by KAL
Sun Oct 15, 2017 7:30 pm
Forum: erskyTx (was ersky9x)
Topic: ERSKY9X Coding
Replies: 4539
Views: 1957418

Re: ERSKY9X Coding

Thank you, Mike

Klaus
by KAL
Sun Oct 15, 2017 7:20 pm
Forum: erskyTx (was ersky9x)
Topic: ERSKY9X Coding
Replies: 4539
Views: 1957418

Re: ERSKY9X Coding

Do you have some centre beeps activated?
Without, nothing to blink.
by KAL
Sun Oct 15, 2017 7:18 pm
Forum: erskyTx (was ersky9x)
Topic: ERSKY9X Coding
Replies: 4539
Views: 1957418

Re: ERSKY9X Coding

Version
20171015_210025.jpg
Video
20171015_211514.mp4
(994.6 KiB) Downloaded 546 times
by KAL
Sun Oct 15, 2017 6:09 pm
Forum: erskyTx (was ersky9x)
Topic: ERSKY9X Coding
Replies: 4539
Views: 1957418

Re: ERSKY9X Coding

Murphy strikes ... ;)

At the moment I have 2 Pros and 3 9XT at hand
and all 5 show this behaviour ...

Klaus
by KAL
Sun Oct 15, 2017 5:47 pm
Forum: erskyTx (was ersky9x)
Topic: ERSKY9X Coding
Replies: 4539
Views: 1957418

Re: ERSKY9X Coding

Hi Mike,

in f2 for Pro and 9XT I noticed a little beauty mistake:

In "Model Setup" - "General"
while setting "Volume Control"
the highlighted parts of "Beep Cnt" are also blinking.

Klaus
by KAL
Sun Oct 15, 2017 11:08 am
Forum: erskyTx (was ersky9x)
Topic: ERSKY9X Coding
Replies: 4539
Views: 1957418

Re: ERSKY9X Coding

MikeB wrote: Sun Oct 15, 2017 10:37 am KAL: I've got the change in for the 9Xtreme to set pot detents. I'll try to post a "f3" either later today or tomorrow ...
No need to post an extra testversion only for me :)

Klaus
by KAL
Sun Oct 15, 2017 9:34 am
Forum: erskyTx (was ersky9x)
Topic: ERSKY9X Coding
Replies: 4539
Views: 1957418

Re: ERSKY9X Coding

Thank you in advance.

Klaus
by KAL
Sat Oct 14, 2017 11:15 pm
Forum: erskyTx (was ersky9x)
Topic: ERSKY9X Coding
Replies: 4539
Views: 1957418

Re: ERSKY9X Coding

Hi Mike,

I updated both my 9XR Pro and 9Xtreme to f2.
On the Pro I found a very nice option to calibrate pots with detent,
but I can't find this option on 9Xtreme. Is this intended?

Klaus
by KAL
Sun May 28, 2017 6:36 pm
Forum: General Information & Rules
Topic: Subscribe or Bookmark
Replies: 1
Views: 7006

Re: Subscribe or Bookmark

Please click on the wrench symbol at page bottom (or top) ...

Klaus
by KAL
Sat May 20, 2017 3:10 pm
Forum: Hardware
Topic: having issues with USBASP driver
Replies: 55
Views: 29773

Re: having issues with USBASP driver

Don't know what to hell is all the fuss about. I have several Win10 systems (pro, 64) here and no problems with usbasp. Drivers installed via Zadig. Only downside I found is this: Arduino IDE (1.6.10) (with avrdude 6.3) only works with WinUSB drivers provided e.g. by Zadig (2.2). But avrdude 5.1 pro...
by KAL
Sat Apr 29, 2017 10:00 am
Forum: Hardware
Topic: Noob Confusion with 9X Calibration and trim Display
Replies: 5
Views: 4876

Re: Noob Confusion with 9X Calibration and trim Display

What does the 'DiagAna' screen in the radio setup show for the sticks?

Did you create a new model?
If not: What about the 'sub trim' in the limits menu?

Klaus
by KAL
Tue Apr 25, 2017 4:47 pm
Forum: ersky9xr
Topic: RESOLVED: Template does not setup mixes using TAER order?
Replies: 70
Views: 43817

Re: Template does not setup mixes using TAER order?

Maybe I'm a bit goofy here but I don't understand what you mean with ELE and PITCH Servo. This names belong to mechanical mixing where you indeed have separate servos for pitch, nick and roll. But nevertheless: If you used the template the swash type is set to '120'. For this the rear servo should b...
by KAL
Tue Apr 18, 2017 8:15 pm
Forum: ersky9xr
Topic: RESOLVED: Template does not setup mixes using TAER order?
Replies: 70
Views: 43817

Re: Template does not setup mixes using TAER order?

Why does it not set up the correct TAER order making my throttle ch1, etc? TAER is not applicable to heli mode. A CCPM flybar heli doesn't have regular aileron or elevator!! :shock: You have 3 servos to tilt (cyclic pitch) or lift (collective pitch) the swash plate. Usually ch1 to ch3 are the so ca...
by KAL
Wed Mar 22, 2017 7:38 pm
Forum: erskyTx (was ersky9x)
Topic: ERSKY9X Coding
Replies: 4539
Views: 1957418

Re: ERSKY9X Coding

Thanks in advance

Klaus
by KAL
Wed Mar 22, 2017 6:39 pm
Forum: erskyTx (was ersky9x)
Topic: ERSKY9X Coding
Replies: 4539
Views: 1957418

Re: ERSKY9X Coding

I think you'll have to wait 'til Mike is able to provide his changes to pascal/midelic

PS: though I have some modules from bangood they don't have bind button and dial switch. :oops:
I removed them for some other projects. :D

Klaus
by KAL
Wed Mar 22, 2017 6:07 pm
Forum: erskyTx (was ersky9x)
Topic: ERSKY9X Coding
Replies: 4539
Views: 1957418

Re: ERSKY9X Coding

jhsa wrote: Wed Mar 22, 2017 3:40 pm My module DOES NOT have the bind button as I use serial..
Hi João,

as Mike mentions here, he has to modify the multi code to be able to
automatically switch to bootloader when entering maintenance mode.

Klaus
by KAL
Wed Mar 22, 2017 3:30 pm
Forum: erskyTx (was ersky9x)
Topic: ERSKY9X Coding
Replies: 4539
Views: 1957418

Re: ERSKY9X Coding

Hi João,

in the docs on github under "not for the fainthearted" :)
See here
But I did't had time to test it yet.

Klaus
by KAL
Tue Mar 21, 2017 6:22 pm
Forum: erskyTx (was ersky9x)
Topic: ERSKY9X Coding
Replies: 4539
Views: 1957418

Re: ERSKY9X Coding

Hi Mike,

problem solved. I was just too blind to find it in the docs ... :oops:

Klaus
by KAL
Tue Mar 21, 2017 4:22 pm
Forum: erskyTx (was ersky9x)
Topic: ERSKY9X Coding
Replies: 4539
Views: 1957418

Re: ERSKY9X Coding

Hi Mike,
which bootloader are you using for the multi?
Or can you please provide a HEX-File?

Klaus
by KAL
Tue Feb 28, 2017 10:34 pm
Forum: er9x
Topic: Replace the 9x motherboard, but can't flash er9x?
Replies: 39
Views: 20821

Re: Replace the 9x motherboard, but can't flash er9x?

I suspect your new motherboard is equipped with an Atmega128,
not with an Atmega64.
So you have to flash er9x-128.hex

and NEVER EVER use option -F
you may brick the Atmel.

Klaus
by KAL
Sat Feb 25, 2017 8:42 am
Forum: erskyTx (was ersky9x)
Topic: ERSKYTx (was ersky9x) Questions
Replies: 2347
Views: 1333274

Re: ERSKY9x Questions

To the root you have to put it ...
by KAL
Sun Feb 12, 2017 10:43 am
Forum: 9Xtreme upgrade board
Topic: Dead 9Xtreme
Replies: 19
Views: 17336

Re: Dead 9Xtreme

If you decide to desolder the STM with ChipQuick please be careful. There is some 'chickenfood' very close to it (disappears very quickly :) ). I therefore decided to cut each leg of the STM with an xacto-knife and desolder 'em one by one. But there you have the risk to rip off a track together with...
by KAL
Thu Jan 26, 2017 2:57 pm
Forum: erskyTx (was ersky9x)
Topic: ERSKY9X Coding
Replies: 4539
Views: 1957418

Re: ERSKY9X Coding

The new protocols menu looks fantastic.
A lot easier to work with.

Klaus
by KAL
Thu Jan 26, 2017 9:33 am
Forum: erskyTx (was ersky9x)
Topic: ERSKY9X Coding
Replies: 4539
Views: 1957418

Re: ERSKY9X Coding

Hi Mike,

while trying to save the eeprom content of my revived 9XT I found a problem with eepskye.
Since rev 421, Nov. 10 2016 eepskye shows only 32 models for the 9XT while the 9XT itself handles 60 models.
Rev. 421, Juli 31 2016 however did handle 60 models.

Klaus
by KAL
Wed Jan 25, 2017 6:46 pm
Forum: 9Xtreme upgrade board
Topic: Burned USB port by cross linked cable - DONE
Replies: 16
Views: 15053

Re: Burned USB port by cross linked cable

YEAH HA, I'm (or better: the 9XT is) back in business. :D :D :D :D
Hopefully I will never have to solder parts with such a small pin pitch in the future ;)

Thank you Mike!
by KAL
Wed Jan 25, 2017 5:55 pm
Forum: 9Xtreme upgrade board
Topic: Burned USB port by cross linked cable - DONE
Replies: 16
Views: 15053

Re: Burned USB port by cross linked cable

Hi Mike, I can see light at the end of the tunnel (or is it a train coming? ;) ). The STM is transplanted and DfuSeDemo recognizes it as STM Device in DFU mode, vendor 0483, productID DF11, version 2200. Can the .dfu file be converted from a .bin file or can you please share the .dfu file you mentio...

Go to advanced search