openrcforums

For the XJT module the black wire goes to the SPort signal pin, the white wire is not needed. If you are only using the XJT module, then you may solder the black wire directly to pin 5 (bottom pin) of the module connector. The white wire may be connected to to the +pin if plugging the two-pin conne...

yes, But I could not get my CH6 to move from -100 to +100 in simulator


OK, I wasn't holding my trainer for long enough in the sim
my fault.


Yea, I think I want to see if I can play with that and change it to both !TRN and THR simultaneously.


Thanks.
David.

I believe that in the installation folder there is already a "phrase file" to generate all the basic voice files. You just need to add the extra ones you need, select an output folder, select a sexy voice :mrgreen:, and generate the files. ^^^ Ha! you sound so feminine! lol Pasted that in...

They both should work. Well at least now you have learnt how to work with logical switches :) ;) João João, I didnt mean to insinuate that your didn't work. Just that I was unclear as to what I wanted to achive. Also to clarify that Mike's original suggestion worked, but I was unable to test in eeP...

L1 Ntme Off 0.6 On 6 AND TRN L2 v<val Thr -99 AND !THR L3 AND L1 L2 L4 Latch L3 THR then use L4 as the source of the arming channel. Mike. I now know why I couldn't get this to work on simulator. Cant click !TRN and THR at same time in eePskye simulator. duah. Mike is the man, João's Model was just...

I failed my exam. lol Did my first bench test on live model ( no props! ) switches didn't act as expected. I am 100% sure this is operator error. :) I will double check my default setting like suggested by Mike (I have also yet to try Mike's example need to try and learn that.) I use the THR switch ...

Same as above, but the Thr stick must also be at minimum, otherwise the flight controller won't arm. CH6 100% FULL (Switch) L4 CH14 +100% sTRN Delay(u0.6:d0) L1 CH14 > 98 (and) !THR L2 v<val Thr -98 (and) L1 (This checks that the throttle stick is down AND that L1 is ON) L3 OR TRN THR L4 Latch L2 L...

Mike you are THE MAN!

ersky9x-r218 9xt 8-1-16 well, I guess its good and bad that you guys are playing and finding stuff that needs looking at. Didnt mean to cause work for you Mike. :) Ok, I need to sit and play with these options and double check that I am not messing something up stupid in my programing and causing th...

ch6 +100%sL2 I then set the L1 and L2 switches like stated L1 v>val CH14 98 L2 Latch L1 TRN (AND switch) THR simulated, ch6 will go from -100 to +100 with the thr switch with no regard to trainer. trainer does delay, I can see that. You will need a mix in channel 14 as I explained above. CH14 100% ...

ok guys great suggestions, but I cant get either of them to work. since I dont know log switches too well,(or at all) I can kinda get my head around Joao's idea of using ch14 to trainer delay. tried them first on the radio, was missing the AND part on mikes examples, the ( and) helped me see what I ...

Freerider needs the mixes to be set up specifically. From memory, they need to only go from 0 to +100%, so use a weight of 50% and an offset of 50%. Mike. I've got a new model created specifically for use with a sim, and I have the protocols set Internal: On, 6ch, 300uS, Polarity: NEG, and Ext: Off...

Hi guys, Been playing with program, trying to learn the in's and out's. Just got first quad and setting up the Naze32 r6. got her up and running, here are the stats.... 9Xtreme board FRYsky module crappy ppm original hobbyking 8ch receiver. (I know these suck and shouldn't be using it my only other ...

Mike & João , Yes I was using the eepe with the er9x so I have a few models saved. I have just transferred 20 models using the drag and drop, (lots of duplicate test versions that I had..) over to eepskye and I am going threw the programs to see how they worked. before that I was manually openin...

João, Worked exactly like you wrote it! You sir are a savior! just the type of idiot leading instructions that I needed. :) looks like those other directions left out the part to save it to the memory card. bootloader says: v1.8 ready then lists the xt_rom.bin file radio says: SVN: ersky9x-r218 Gues...

Hey guys, I upgraded my 9x with the old smartie rev2.4 with the newer 9Xtreme board. cant seem to update the boot loader. I suck at this programing stuff. grrr. I know this should be clear cut, but cant seem to get either of these processes to work. bootloader says v1.7ready... no firmware but my ve...

I haven't had time to try to learn this eepe but today I think I made some sense of what you wrote... I'm slow I know... First off, I don't have a MSR manual, and the one I downloaded doesn't have settings for programable radio.... I did get it to fly and hover this is where I am at right now with i...

thanks for all the help guys!
the board and my back light are installed. the eepe is running and er9x is loaded and I can fly one of my heli's. now I need templates and learn how to use eepe programing! wish me luck!

Also, I know I bind the dsm module with the trainer switch. but I dont know if Iam doing it 100% correct with hitting the joystick to one side or an other... ect.
any help on this would be cool also.
total newbie I know.

is there a link some where to a gathering of templates for different models? I dont know how to build one yet, still learning. the 4 heli's I have right now are: Module 1 ....my factory flsky module from the HK v2 9x Xedia 9958 this is the model fro hacksmod.com ( I have this one loaded up and runni...

I havent been able to find a mSR template for eePe. search and google were no help.
Anybody got one.

Just got my er9x installed and have my 9958 up and running! w00t!
I downloaded the Nano cpx and plugging in my DSM module right after I hit enter!

Steven,
Thanks for the response, did not expect to hear from the builder of this board! awesome. Sorry you have to answer silly stupid questions from insecure newbies like me.

Ok guys, newbie to programing here so be gentile... I have been running my HK 9x v2 for about six months or so. I use it for flying my modified 9958 heli. I really dig this controller and know what it is capable of in the right hands. I had bought a Used BNF Blade Nano CPX that needed a bit of work ...