Search found 19 matches

by igorc
Fri Nov 15, 2013 7:31 pm
Forum: General help (FrSky Taranis radio)
Topic: Replacement Battery For FrSky Taranis
Replies: 50
Views: 33333

Re: Replacement Battery For FrSky Taranis

I think I will go for the 6 ni-mh solution, with the turnigy 2400mah. My taranis has not arrived yet from hobbyking, it should be a B version, will it contain the first 800mah battery or the new 2000mah, in which case no need for a replacement battery?

Envoyé depuis mon GT-I9100 avec Tapatalk
by igorc
Fri Nov 15, 2013 4:18 pm
Forum: General help (FrSky Taranis radio)
Topic: Replacement Battery For FrSky Taranis
Replies: 50
Views: 33333

Re: Replacement Battery For FrSky Taranis

Hi,

Can someone tell me the dimensions of the taranis battery case ?

Also, frsky state that the operating voltage is 6v-15v, but is it safe to use a 6.6v 2S lifePo battery ? also when the battery is discharged, will the radio cut off if the voltage go down 6v ? (I'm thinking about this battery)
by igorc
Sat Oct 12, 2013 7:42 am
Forum: openTx
Topic: Turnigy 9x wont controle the receivers after Open9x upgrade
Replies: 41
Views: 20685

Re: Turnigy 9x wont controle the receivers after Open9x upgr

no, open9x did not controlled the servos, I flashed er9x, the servos was controlled. lately I flashed again open9x with the same result, now I will stick on er9x ;)
by igorc
Wed Sep 11, 2013 9:44 am
Forum: openTx
Topic: Turnigy 9x wont controle the receivers after Open9x upgrade
Replies: 41
Views: 20685

Re: Turnigy 9x wont controle the receivers after Open9x upgr

jhsa wrote:glad you fixed it. Well done. ;) And now we know that at least one person fixed it using an arduino :mrgreen:
DAHAHAHAHA YESS !!! :D :D :D :D :D :D :D
by igorc
Wed Sep 11, 2013 1:06 am
Forum: openTx
Topic: Turnigy 9x wont controle the receivers after Open9x upgrade
Replies: 41
Views: 20685

Re: Turnigy 9x wont controle the receivers after Open9x upgr

I flashed ER9X, and IT WORK, the servos move !
It was a problem with opentx :?

I will stay with this setup.

Thank you again all !
by igorc
Wed Sep 11, 2013 12:55 am
Forum: openTx
Topic: Turnigy 9x wont controle the receivers after Open9x upgrade
Replies: 41
Views: 20685

Re: Turnigy 9x wont controle the receivers after Open9x upgr

And thank you sooooo much all, I would not have succeeded without you! ;) :)
by igorc
Wed Sep 11, 2013 12:20 am
Forum: openTx
Topic: Turnigy 9x wont controle the receivers after Open9x upgrade
Replies: 41
Views: 20685

Re: Turnigy 9x wont controle the receivers after Open9x upgr

huhuhuhuhuhuhuhuhuhuhuhu hahahahahahahahahahahaha I FIXED IT ! I have found a guy here who sells Arduinos, he lent me one, and now my radio is working perfectly! I spent 4 hours, and several test, first wanting to flash directly with the Arduino, which did not work. After I configured the arduino to...
by igorc
Tue Sep 10, 2013 4:43 pm
Forum: openTx
Topic: Turnigy 9x wont controle the receivers after Open9x upgrade
Replies: 41
Views: 20685

Re: Turnigy 9x wont controle the receivers after Open9x upgr

Has anyone successfully fixed his fuse bricked 9x using an arduino as the external Oscillator?!
by igorc
Tue Sep 10, 2013 3:21 pm
Forum: openTx
Topic: Turnigy 9x wont controle the receivers after Open9x upgrade
Replies: 41
Views: 20685

Re: Turnigy 9x wont controle the receivers after Open9x upgr

It depends on what you would want to do with them afterwards.. ;) I don't know, but I think the nano version will have some limitations due to the small size. According to the hk site, all nano, uno, uno R3 and mega have usb input. According to the hk site, the mega is R2 not R3. I think I should t...
by igorc
Tue Sep 10, 2013 2:35 pm
Forum: openTx
Topic: Turnigy 9x wont controle the receivers after Open9x upgrade
Replies: 41
Views: 20685

Re: Turnigy 9x wont controle the receivers after Open9x upgr

Thank you all for the answers, I also prefer the arduino solution. I like the idea to be able to use it for other things, not only throw it once the 9x if fixed. As I'm ordering some stuff from hobbyking, could you tell me what arduino I need ? uno, nano, mega, leonard, ... Also, do I need other stu...
by igorc
Tue Sep 10, 2013 1:38 pm
Forum: openTx
Topic: Turnigy 9x wont controle the receivers after Open9x upgrade
Replies: 41
Views: 20685

Re: Turnigy 9x wont controle the receivers after Open9x upgr

Hi, I'm outside of USA, I can't order from http://www.digikey.com/product-detail/en/ECS-2100A-010/XC229-ND/39059?cur=USD the 1Mhz oscillator. Could you tell me if anyone from the following will do the job ? http://www.ebay.com/itm/5-PCS-1MHz-5-7MM-SMD-4-Pin-1-MHz-1-000MHz-SMT-Active-Crystal-Oscillat...
by igorc
Fri Sep 06, 2013 7:12 pm
Forum: openTx
Topic: Turnigy 9x wont controle the receivers after Open9x upgrade
Replies: 41
Views: 20685

Re: Turnigy 9x wont controle the receivers after Open9x upgr

Emm I did, many times, maybe it's what bricked my radio...

Envoyé depuis mon GT-I9100 avec Tapatalk
by igorc
Fri Sep 06, 2013 4:58 pm
Forum: openTx
Topic: Turnigy 9x wont controle the receivers after Open9x upgrade
Replies: 41
Views: 20685

Re: Turnigy 9x wont controle the receivers after Open9x upgr

I can answer yes to all this question. I have two different USBasp programmers, I upgraded there firmware but this doesnt resolved the problem. I checked the wiring with a multi-mettre and everything is connected as it should, also the voltage between vcc and grn is 5V.
Pictures :
by igorc
Fri Sep 06, 2013 4:02 pm
Forum: PROGRAMMERS
Topic: Updating Usbasp firmware using Eepe in Windows
Replies: 119
Views: 116330

Re: Updating Usbasp firmware using Eepe in Windows

the device is different from the picture on one thing: J2 is only two small holes on my device, not as in the picture, and of course it is off now
by igorc
Fri Sep 06, 2013 3:58 pm
Forum: openTx
Topic: Turnigy 9x wont controle the receivers after Open9x upgrade
Replies: 41
Views: 20685

Re: Turnigy 9x wont controle the receivers after Open9x upgr

Well ... hell on my radio. I tryed to flash the firmware again, the process went ok but then, when I start the radio, I only get a blank screen. I tryed several times with the same result, but now, I even can't flash it, it's not detected by avrdure avrdude.exe: error: programm enable: target doesn'...
by igorc
Fri Sep 06, 2013 3:50 pm
Forum: PROGRAMMERS
Topic: Updating Usbasp firmware using Eepe in Windows
Replies: 119
Views: 116330

Re: Updating Usbasp firmware using Eepe in Windows

Well ... I just flashed the usbasp using a jumper on J2 !
I first tryed j3 as you suggested but the answer was "target doent answer"
by igorc
Fri Sep 06, 2013 12:57 pm
Forum: openTx
Topic: Turnigy 9x wont controle the receivers after Open9x upgrade
Replies: 41
Views: 20685

Re: Turnigy 9x wont controle the receivers after Open9x upgr

the radio asked me to put the sticks on the middle position, and then to move them in the second step, is this what you're talking about ?
by igorc
Fri Sep 06, 2013 12:55 pm
Forum: PROGRAMMERS
Topic: Updating Usbasp firmware using Eepe in Windows
Replies: 119
Views: 116330

Re: Updating Usbasp firmware using Eepe in Windows

Hi, I have this programmer http://i.ebayimg.com/t/USBASP-USBISP-AVR-Programmer-Adapter-10-Pin-Cable-USB-ATMEGA8-ATMEGA128-Arduino-/00/s/ODAwWDgwMA==/z/kA8AAOxyFiRRyWxz/$%28KGrHqZ,!o4FHE%29%295dinBRyW%29zJ!p!~~60_3.JPG bought here on ebay Where have I do make the jumper ? JP1 or JP2 ? and what file t...
by igorc
Fri Sep 06, 2013 8:56 am
Forum: openTx
Topic: Turnigy 9x wont controle the receivers after Open9x upgrade
Replies: 41
Views: 20685

Turnigy 9x wont controle the receivers after Open9x upgrade

Hello, Yesterday I received two USBasp cables and tryed to flash my stock Turnigy 9x. first, all went bad, the first USBasp refused to read the EEPE, then I started the radio : she was out of service, only the backlight start, the radio doesnt start at all. I tryed the second USBasp, he told me that...

Go to advanced search