Search found 138 matches
- Thu Jan 28, 2021 7:34 am
- Forum: openTx model setup
- Topic: Weight or End Points?
- Replies: 1
- Views: 4165
Weight or End Points?
When setting up a new model and once I have mechanically set the control surface throws as best I can to the model manufacturers specifications, I fine tune the final desired movements on the Tx. As far as I can see there are two ways to do this. Either by adjusting the weight or the end points. Wha...
- Wed Jan 27, 2021 3:00 pm
- Forum: General help (FrSky Taranis radio)
- Topic: Post Deleted
- Replies: 2
- Views: 3041
Deleted
Deleted.
- Wed Jan 27, 2021 9:25 am
- Forum: General help (FrSky Taranis radio)
- Topic: SR10 Pro - Channels?
- Replies: 5
- Views: 4833
Re: SR10 Pro - Channels?
The attached is a how to I found on another forum demonstrating how to change the pin channel order on SR10 Pro Rx.
- Wed Jan 27, 2021 9:21 am
- Forum: General help (FrSky Taranis radio)
- Topic: Archer SR series Custom failsafe autolevel not working
- Replies: 1
- Views: 2858
Re: Archer SR series Custom failsafe autolevel not working
I was reading this https://www.rcgroups.com/forums/showthr ... rs-Release
Others are reporting the same problem. Frsky have acknowledged it's a bug and intend to fix it at next FW release.
Others are reporting the same problem. Frsky have acknowledged it's a bug and intend to fix it at next FW release.
- Wed Jan 27, 2021 6:05 am
- Forum: General help (FrSky Taranis radio)
- Topic: Post Deleted
- Replies: 2
- Views: 3041
Post Deleted
Deleted - in wrong place.
- Wed Jan 20, 2021 5:53 pm
- Forum: General help (FrSky Taranis radio)
- Topic: Access Protocol: Rx Registering
- Replies: 1
- Views: 2136
Access Protocol: Rx Registering
I have a new Access Rx and two Access Tx's. I want to register the Rx with both Tx's. I don't have a problem doing that. But my question is about adding new models. The Registration function is in the Model Setup menu. Does that mean that only that Model entry in the Tx's will be registered with the...
- Sat Nov 07, 2020 12:03 pm
- Forum: General help (FrSky Taranis radio)
- Topic: SR10 Pro - Channels?
- Replies: 5
- Views: 4833
Re: SR10 Pro - Channels?
Penny has dropped.........
So, for example, channel 13 could be assigned to pin 9 and channel 14 to pin 10. Thus preserving the pins as being usable. Have I got this right?
So, for example, channel 13 could be assigned to pin 9 and channel 14 to pin 10. Thus preserving the pins as being usable. Have I got this right?
- Sat Nov 07, 2020 9:57 am
- Forum: General help (FrSky Taranis radio)
- Topic: SR10 Pro - Channels?
- Replies: 5
- Views: 4833
SR10 Pro - Channels?
Just bought one of these new Archer receivers. There are 10 PWM outputs but the manual appears to have been created by cut n pasting the channel configuration from the S8R manual. For instance, channel 9 for gain, channel 10 (Quick Mode) for flight modes. How can this be so when these channels have ...
- Sun Oct 25, 2020 4:24 pm
- Forum: General help (FrSky Taranis radio)
- Topic: ACCESS D16 FW Version?
- Replies: 8
- Views: 4995
Re: ACCESS D16 FW Version?
Is the hardware some how factory set via some kind of internal ROM This, in order to prevent people from being able to change it. Found it. Radio Setup 7/7 Modules / RX Versions. Set to EU and I can't change it. Not even if I change Country Code on 3/7. Therefore, I now know that my Rx's will need ...
- Sun Oct 25, 2020 3:22 pm
- Forum: General help (FrSky Taranis radio)
- Topic: ACCESS D16 FW Version?
- Replies: 8
- Views: 4995
Re: ACCESS D16 FW Version?
The region of ACCESS modules is not stored in the firmware anymore, so the same module firmware will transmit either one depending on what the hardware was set to. Is the hardware some how factory set via some kind of internal ROM or does the region setting in OpenTx control this via Radio Setup 3/...
- Sun Oct 25, 2020 7:43 am
- Forum: General help (FrSky Taranis radio)
- Topic: ACCESS D16 FW Version?
- Replies: 8
- Views: 4995
- Sat Oct 24, 2020 12:59 pm
- Forum: General help (FrSky Taranis radio)
- Topic: ACCESS D16 FW Version?
- Replies: 8
- Views: 4995
Re: ACCESS D16 FW Version?
D16 has been there from the start and there are both versions. Thanks. Frsky are recommending v2.1.0 for the internal module. However, there is no LBT / FCC option in the download folder for the ISRM internal module. When I come to upgrading my X8R Rx I can choose between FCC / LBT. Any idea which ...
- Sat Oct 24, 2020 10:04 am
- Forum: General help (FrSky Taranis radio)
- Topic: ACCESS D16 FW Version?
- Replies: 8
- Views: 4995
ACCESS D16 FW Version?
I've got one of the newer Tx's (X9D Lite) that has the ACCESS protocol. Recently, the D16 protocol has been added. My question is what ACCST FW version of D16 is this using? If it's the newer v2.1.0 then I guess I'm going to have to upgrade the FW in my Rx's for everything to work together.
- Sat Oct 10, 2020 1:45 pm
- Forum: General help (FrSky Taranis radio)
- Topic: S6R Rx on IC Fixed Wing?
- Replies: 1
- Views: 1964
S6R Rx on IC Fixed Wing?
Has anyone successfully flown an IC fixed wing model with the S6R? Last time I tried a stabiliser in an IC model the vibration sent the thing haywire. TIA.
- Sun Aug 09, 2020 1:21 pm
- Forum: Hardware
- Topic: Archer R6 - RSSI Warnings
- Replies: 5
- Views: 4600
- Sun Aug 09, 2020 11:23 am
- Forum: Hardware
- Topic: Archer R6 - RSSI Warnings
- Replies: 5
- Views: 4600
Re: Archer R6 - RSSI Warnings
The OpenTx defaults are Low alarm 45 and Critical alarm 42. That's both on the X9D Lite and QX7 Tx's. Range check at these values is OK. On a typical 7 min flight with my Max Thrust Riot I'm getting 4 or 5 voice warnings. Not flying too far out. I'll lower the settings to 35 and 32 respectively next...
- Sun Aug 09, 2020 9:44 am
- Forum: Hardware
- Topic: Archer R6 - RSSI Warnings
- Replies: 5
- Views: 4600
Archer R6 - RSSI Warnings
I've recently acquired a Frsky X9D Lite Tx and an Archer R6 Rx. When flying I keep getting RSSI low / critical voice warnings. I've moved the Tx antenna to different positions to avoid the dead spot but it keeps happening. The Tx is running the latest version of OpenTx. I think I read somewhere that...
- Sun May 12, 2019 9:18 pm
- Forum: erskyTx (was ersky9x)
- Topic: ErskyTX
- Replies: 0
- Views: 2905
ErskyTX
Is a name change required to this thread or is there another thread I've missed?
- Fri May 10, 2019 5:55 pm
- Forum: General help (FrSky Taranis radio)
- Topic: Access Protocol - HowTo?
- Replies: 3
- Views: 4794
Re: Access Protocol - HowTo?
FrSky have a new menu item on their website for the protocol here:https://www.frsky-rc.com/frsky-advanced-communication-control-elevated-spread-spectrum-access-protocol-release/ It has download links for the new FW on a range of Rx's but no instuctions on how to flash the Rx's nor what version of Op...
- Fri May 10, 2019 5:36 pm
- Forum: General help (FrSky Taranis radio)
- Topic: Access Protocol - HowTo?
- Replies: 3
- Views: 4794
Access Protocol - HowTo?
I've seen that FrSky have recently launched this new protocol. It looks good to me. I have a QX7 running OpenTx 2.1. and a bunch of various FrSky Rx's. I'm trying to find a HowTo that describes how I can take advantage of the new protocol. Any links greatly appreciated.
- Thu May 09, 2019 7:16 pm
- Forum: erskyTx (was ersky9x)
- Topic: ErskyTX
- Replies: 2
- Views: 3716
Re: ErskyTX
Got it. Thank you. Excellent FW. Thanks to Mike.
- Thu May 09, 2019 7:05 pm
- Forum: erskyTx (was ersky9x)
- Topic: ErskyTX
- Replies: 2
- Views: 3716
ErskyTX
Does anyone know what this FW is please:https://www.t9hobbysport.com/frsky-tara ... osQbY4N6YQ
- Fri Aug 10, 2018 5:33 pm
- Forum: openTx
- Topic: Variable End Point?
- Replies: 1
- Views: 2265
Variable End Point?
I'm installing a Bavarian Demon Cortex in a petrol model. The tutorial vid shows a 3 POS switch being used to change flight modes. A Spectrum radio is used in the vid and it recommends using "end points" the adjust the gain. In OpenTX I can assign a 3 POS switch just the same as in the vid...
- Thu Jul 12, 2018 9:30 pm
- Forum: openTx
- Topic: "Smart" Throttle Cut?
- Replies: 47
- Views: 31556
Re: "Smart" Throttle Cut?
If you look at the "How To" section of my OpenTX documents in this section of the forum, you will find there is a smart throttle cut/arming routine which is very simple, but almost foolproof. Not only does it require the throttle to be at zero, but the switch has to be activated at betwee...
- Wed Jul 11, 2018 9:38 am
- Forum: openTx
- Topic: "Smart" Throttle Cut?
- Replies: 47
- Views: 31556
Re: "Smart" Throttle Cut?
Create a function entry for all the logical switches you need, then close and re-open the editing window. All logical switches that have a function entry will now appear in the drop down lists. I did this and with the LS/SF lines Joao provided then the switch is working as a safety switch as intend...
- Mon Jul 09, 2018 8:43 pm
- Forum: openTx
- Topic: "Smart" Throttle Cut?
- Replies: 47
- Views: 31556
Re: "Smart" Throttle Cut?
This is my last attempt. after this i don't know what else to do.. This works. it is easy enough to find that L1 is the same as L01, L2 is the same as L02, and L3 is the same as L03. Please look at the pictures.. Yes, I get all of that. And I do understand that L1 is the same as L01 etc. But you ar...
- Mon Jul 09, 2018 8:10 pm
- Forum: openTx
- Topic: "Smart" Throttle Cut?
- Replies: 47
- Views: 31556
- Mon Jul 09, 2018 7:20 pm
- Forum: openTx
- Topic: "Smart" Throttle Cut?
- Replies: 47
- Views: 31556
Re: "Smart" Throttle Cut?
I probably have an old companion, L01, L1, is all the same. I believe it is quite obvious Thanks for trying to help. I've done much research on this and the consensus is that the inputs for logical switches in previous versions of Companion and OpenTx prior to 2.2.1 work fine for the objective I'm ...
- Mon Jul 09, 2018 6:27 pm
- Forum: openTx
- Topic: "Smart" Throttle Cut?
- Replies: 47
- Views: 31556
Re: "Smart" Throttle Cut?
The first line of your L1 text does not match the input lines for Companion 2.2.1
The line begins with the name L01, not L1. After that the inputs do not match. Attached is a screen shot of the Logical input screen from Companion 2.2.1 in QX7 profile.
The line begins with the name L01, not L1. After that the inputs do not match. Attached is a screen shot of the Logical input screen from Companion 2.2.1 in QX7 profile.
- Mon Jul 09, 2018 6:08 pm
- Forum: openTx
- Topic: "Smart" Throttle Cut?
- Replies: 47
- Views: 31556
Re: "Smart" Throttle Cut?
It seems there is no simple way to get sticky Thr-cut in OpenTX, so what kind of help do you need? I don't understand.. :o Here is a way to do it.. Logical switches: L1 AND SFv L2 L2 OR L1 L3 L3 a<x Thr -96 Special Functions: SF1 !L1 Override CH3 -100 (then tick the "ON" box) I have tried...