Search found 22 matches

by Hegu78
Fri May 31, 2013 7:23 pm
Forum: openTx
Topic: Mixer warning beep timing on Opentx
Replies: 2
Views: 2699

Re: Mixer warning beep timing on Opentx

It beeps continuously whenever the mixer line is active (in bold). Thanks for immediate reply! I tried to remove my channel 13 workaround mix and add warning directly to ch7. It beeps first time about 1-2 seconds from line is active (physical switch is switched) and keeps beeping. Next beep timing ...
by Hegu78
Fri May 31, 2013 7:10 pm
Forum: openTx
Topic: Mixer warning beep timing on Opentx
Replies: 2
Views: 2699

Mixer warning beep timing on Opentx

Wiki says: "A sound warning (1, 2 or 3 beeps) can be set to play when the line is active." When it should beep with slow speed curve drive, beginning, end, middle in time, middle in travel or random? Some background: I use curve for servo movement for channel 7 and beep plays somewhere in ...
by Hegu78
Fri May 31, 2013 12:53 pm
Forum: er9x / gruvin9x / th9 based firmwares
Topic: Automated servo movement ... is it possible ?
Replies: 10
Views: 8027

Re: Automated servo movement ... is it possible ?

This version (autocam 2) has function that if ELE switch is ON then loop runs and if ELE switch is OFF loop runs but don't move camera servo. So far I didn't find way to stop loop, just bypass it.

Henri
by Hegu78
Fri May 31, 2013 9:42 am
Forum: er9x / gruvin9x / th9 based firmwares
Topic: Automated servo movement ... is it possible ?
Replies: 10
Views: 8027

Re: Automated servo movement ... is it possible ?

And here is something to study. I think this does what you originally asked for. AutoCAM 0.eepm -Gohst Thanks gohsthb. This is nice start for making great camera shutter control. Now we have automation for camera focus and shutter and this is repeated all the time when RX/TX is on. If this is devel...
by Hegu78
Wed May 29, 2013 3:42 am
Forum: er9x / gruvin9x / th9 based firmwares
Topic: Automated servo movement ... is it possible ?
Replies: 10
Views: 8027

Re: Automated servo movement ... is it possible ?

Name Autocam looks promising. I'll check it out this week.

Thanks!

Henri
by Hegu78
Tue May 28, 2013 2:21 pm
Forum: er9x / gruvin9x / th9 based firmwares
Topic: Automated servo movement ... is it possible ?
Replies: 10
Views: 8027

Re: Automated servo movement ... is it possible ?

Why not make your switch set the servo to go to max on one click. Then... make a custom switch that sets it to 0 after it reaches max. Sent from my GT-I9300 using Tapatalk 2 This sounds good but so far I don't know how it is done. I will try to learn this week. I still need curves or something else...
by Hegu78
Tue May 28, 2013 3:54 am
Forum: er9x / gruvin9x / th9 based firmwares
Topic: Automated servo movement ... is it possible ?
Replies: 10
Views: 8027

Re: Automated servo movement ... is it possible ?

Look at the servo test template, and also there are other automated tamplates in the template area of this forum, including a search light movement and led flashing. It can be done. Where is template area of this forum? I try to achieve camera shutter function so that I have prepress for focus and ...
by Hegu78
Sat May 18, 2013 7:46 pm
Forum: Hardware
Topic: People willing to help with modifications
Replies: 52
Views: 74957

Re: People willing to help with modifications

Location: Finland One my friend has good skills in electronics and said he is able to do mods for others also. He doesn't have RC-experience but has that whole family good electronics skills and experience. Finnish: Yksi kaverini (Somerolla) voi tehdä radioiden modauksia muillekin mikäli tarpeen on....
by Hegu78
Sat May 18, 2013 5:43 am
Forum: Hardware
Topic: Frsky telemetry to 9xr on screen with opentx
Replies: 20
Views: 16629

Re: Frsky telemetry to 9xr on screen with opentx

Now everything works. I set range to 13.2v as Kilrah said and now I get receiver battery voltage also. All that information on radio actually makes or could make possible to instrument flight. This offers more than I expected. I use to have pocket camera equipments on board and Bixler is often as hi...
by Hegu78
Thu May 16, 2013 5:48 pm
Forum: Hardware
Topic: Frsky telemetry to 9xr on screen with opentx
Replies: 20
Views: 16629

Re: Frsky telemetry to 9xr on screen with opentx

Now test run around yard is done. Everything works perfectly except reveiver battery voltage measurement. I'll order voltage divider as Showmaster recommended but is there any change to get that voltage information without? Receiver manual says following: " 2) When side port pins of A1 and X ar...
by Hegu78
Thu May 16, 2013 4:38 pm
Forum: Hardware
Topic: Frsky telemetry to 9xr on screen with opentx
Replies: 20
Views: 16629

Re: Frsky telemetry to 9xr on screen with opentx

Do not plug anything in the A1 or A2 ports except the Frsky resistor divider or one you make. ANY voltage directly into these ports A1 or A2 will destroy your receiver! They are not for servos, they are not for powering other circuits, they are "analogue voltage Inputs only" and must be l...
by Hegu78
Thu May 16, 2013 3:31 pm
Forum: Hardware
Topic: Frsky telemetry to 9xr on screen with opentx
Replies: 20
Views: 16629

Re: Frsky telemetry to 9xr on screen with opentx

What rx are you using? I'm using frsky D8R-2PLUS. So if I understood correctly, I can't use A1 or A2 port for powering my RX and electronics up and same time for measuring my receiver battery voltage (ie. Plug my receiver battery directly to A1 or A2)? I have 3xNIZN cells which has total voltage of...
by Hegu78
Thu May 16, 2013 2:16 pm
Forum: Hardware
Topic: Frsky telemetry to 9xr on screen with opentx
Replies: 20
Views: 16629

Re: Frsky telemetry to 9xr on screen with opentx

I'm studying now how connections should be for measuring my receiver battery pack voltage. I understood that both A1 and A2 would do that. But manual says:"Warning: Battery or servos are NOT to be plugged into side ports (A1/A2/Rx), otherwise damage may occur." How can I measure pack volta...
by Hegu78
Wed May 15, 2013 7:06 pm
Forum: Hardware
Topic: Frsky telemetry to 9xr on screen with opentx
Replies: 20
Views: 16629

Re: Frsky telemetry to 9xr on screen with opentx

You need to set UsrProto to Hub and the Range for the dividers you might want to connected to A1/A2 on the telemetry setup page. You Kilrah are fastest support I have met :!: I found UsrProto selection from radio telemetry settings and changed it to hub (Saying this I perhaps save someone from goog...
by Hegu78
Wed May 15, 2013 6:15 pm
Forum: Hardware
Topic: Frsky telemetry to 9xr on screen with opentx
Replies: 20
Views: 16629

Re: Frsky telemetry to 9xr on screen with opentx

Now on screen telemetry mod is done :D and works partially :( . I get RX and TX strength to screen but all other values are zeros. I' believe i'm missing something important on settings but would you help me to find what it is? Sensors and other equipments are: Frsky gps and vario,frsky FLVS-01 volt...
by Hegu78
Mon May 06, 2013 3:39 am
Forum: The Pickled Gnu (The Pub)
Topic: French/English Translator Needed
Replies: 12
Views: 6681

Re: French/English Translator Needed

There is a french manual and version of the opentx firmware? Or am I missing the point? Sent from my GT-I9300 using Tapatalk 2 You are not, I did. I was reading French manual which was partially translated and same time found this topic and didn't read well enough from beginning. This was for artic...
by Hegu78
Sun May 05, 2013 7:12 am
Forum: The Pickled Gnu (The Pub)
Topic: French/English Translator Needed
Replies: 12
Views: 6681

Re: French/English Translator Needed

Hi, Would it be possible to translate one sentence from here and there same time while learning from trial and error ? Today I tried to learn LiMITS and perhaps could be able to translate something from there. Google translator helps to understand enough for trying and then it is possible to rewrite...
by Hegu78
Sat May 04, 2013 7:21 am
Forum: Software
Topic: Flash from stock 9xr to Opentx, save settings
Replies: 4
Views: 4459

Re: Flash from stock 9xr to Opentx, save settings

I tried this and Companion said "invalid binary eeprom file". I tried also read eeprom from tx but I got similar message. I decided to follow Kjell Kernen tutorial step by step. I learned that those compilation selections are just an options to be added or removed for default Opentx. Basic...
by Hegu78
Sat May 04, 2013 5:28 am
Forum: Software
Topic: Flash from stock 9xr to Opentx, save settings
Replies: 4
Views: 4459

Flash from stock 9xr to Opentx, save settings

Would someone guide a little what should I take care of before first flash from stock 9xr to Opentx? what is done now: - companion9x is installed - HK AVR programmer set up and drivers installed - I have tried read flash from radio and it worked, at least I saw progress bar - I guess this is so new ...
by Hegu78
Wed May 01, 2013 9:31 am
Forum: Hardware
Topic: Frsky telemetry to 9xr on screen with opentx
Replies: 20
Views: 16629

Re: Frsky telemetry to 9xr on screen with opentx

Hmm no, doesn't seem to be in the PDF although he says somewhere in the thread that he would add it... Ok then it wasn't that simple. I lead this a little side from topic because there seems to be to variations. First is like PDF describes and another is more advanced with one extra wire for some a...
by Hegu78
Wed May 01, 2013 5:49 am
Forum: Hardware
Topic: Frsky telemetry to 9xr on screen with opentx
Replies: 20
Views: 16629

Re: Frsky telemetry to 9xr on screen with opentx

At the beginning yes, but if you read a bit further he added the instructions/benefits of the 2nd one (at least after someone else mentioned it). Yes, just with TxD you can't program factory alarm settings, but I found they (factory alarm settings) are good enough for, if I can say, most of people....
by Hegu78
Tue Apr 30, 2013 11:16 am
Forum: Hardware
Topic: Frsky telemetry to 9xr on screen with opentx
Replies: 20
Views: 16629

Frsky telemetry to 9xr on screen with opentx

Hello all, This topic has been discussed tons of times but still I'm not 100% sure how to do modifications. This is best I have found: http://forum.turnigy9xr.com/converting-9xr-to-frsky-telemetry-djt-module-t362.html It advices to flash er9x. Does opentx work as well? My friend with good electronic...

Go to advanced search