openrcforums

Hello again,
I`m looking for a nice openTX function to slow down the "servos" (in actual case the gimbal`s) movement.
It should start and stop the movement very slowly in order to improve the bad tilt attitude of DJI H3 3D.

Any help is welcome!
Regards

Koffer

I'm noticing the same effects on the new SmartPort FCS Sensor and cannot cortect it by offset, too:(
Maybe just a faulty sensor?

OpenTX 1.99 Version 2014-04-28 Channel Range of internal RF module ist messed up after Firmware upgrade (from an ealrier 1.99 Version). It changes to Channels 5-16 instead of previous 1-16. Unfortunately it is not fixable on te transmitter itself, the radio freezes when trying to correct it. Regards...

There is also a LiFePo from Zippy 3s1800. That is the maximum of energy you can put into the Taranis in case of LiFePo.

It fits perfectly, just remove the foam of the battery box.

@mstrens
You may be right, i was a bit confused with voltage, mAH, current and power.

Hello together, after I was quite happy about the FAS Offset function, unfortunately the mAh consumption still is not correct at all, although the current is perfectly calibrated at least up to 10A (my Multimeters range). Now there´s left the voltage, which of course also influences the mAh calculat...

I'd like to give further Information but I rarely can.

When programming and selecting the active line, the command should become bold, shouldn't it?

I'll try to give more Information soon.

The sticky function does not always work (version 16th march). Sometimes it does work, sometimes not.

Sorry Kilrah, i didn't get it with the new Sticky function.
Tried your command line in Logical Switches, but it didn't work.

Otherwise no worry, i can wait for the official release and updated manual.

Wow, that are great news. Will forward testing all the new features as long as there is no irresponsible risk when testing, flashing and using. ..

Will the toggle Switch function "Sxt" stay in OpenTX 2?

In the last Beta Version I miss it.

After first test with satisfiyng results I had to notice that there seem still to exist some special Cell voltage configuration that confuse the sensors data telemetry:

When can we expect to get version 2.0?

Or please release just the offset feature in order to finally get correct consumption readings...

Tell me of I can help out with a Log, that contains this issue (have lots of them).

Unfortunately, the issue still exists in the latest Firmware 2940.

Maybe we have to wait for the next major update to OpentTx 2.0...

Hello,

thanks for your ideas, but the vario is already updated.

I´ve ordered new hardware (SmartPort current sensor and Lipo sensor) and will check then again. Perhaps something on the sensors PCB has fault connections...

Regards

Koffi

Hello guys,

since a long while, I´ve often problems with my Taranis, that sporadically looses correct telemetry reading and logging.

I´m still unsure what could cause this. My setup is X8R, SmartPort Vario (used as bridge), FLVS and FAS40.

Do you have any suggestions?

Regards

Koffi

Thanks for your hints.

Now I took one of the pins in module slot and regelated the voltage aftermath to 5V via linear voltage regulator.

This way there shouldn't be damage to Taranis, I hope.

In order to power an LCD and receiver module for FPV I'm looking for

- stable and clean 5V Source for the receiver
- full voltage for the LCD monitor

Perhaps someone has already done similar Hardware mods...

Regards

Koffi

Thanks for your ideas. I'll Check them out...

Hello,

Is there an Solution to monitor every cell voltages (including Alarm settings) for batteries that are connected in parallel.


I'd like to monitor two of 3s Lipos on my copter and could only find the schematics for serial
Lipo connection (up to 12s)

Thank you for any input!

Koffi

I had a similar Problem with FAS. It was the Sensors that was defective, no idea why...

Thanks to Kilrah, the updating process now finally worked.

I had to remove the sensor fram all connections to the model (SpOrt, DatIN) and then follow strictly the updating sequence as described by Kilrah.

The SPC-Adapter seems to work nicely...

Hi Kilrah,

Thank you for the Support.

I'll try again tomorrow.

I recently tried to update my SPort-Vario but unforunately failed (finding device...) Is this Firmware recommended for both versions of the new varios (normal- and high-precision)? Where should the cable be connected, with the device itself or will it find the correct device via SPort? I used the FU...

Thanks for your help.

This means, with Taranis there is no need to think about it, nice to hear!

Ok, that was the go-around I already found by myself

I just wanted to make sure, that there is some easy feature of OpentX, I wasn´t aware of yet.

Then the "fighting" with the mixer menu was appropriate...

Thanks

Koffi

Hello together, Is ist possible to setup the desired trainer setup for each model seperately? The Ideal is as following: - in case of an FPV Copter the Stick inputs should be replaced by the student (Spotter) - in case of a plane used to teach newbies to fly, the stick inputs should be mixed togethe...

Hi Helle,

thanks for the tutorial.

Unfortunately, the audiorecorder doesn´t seem to exist in this form on Win7 PCs:(

Hello,

the title says it all:

What is difference between saving a template as .bin or .eepe-file?

Is there any advantage of one of these over another?

Thanks

Koffi