openrcforums

Hi Mike thanks for your interest What module are you using? DJT I ´ve allready try this to mods: First http://forum.turnigy9xr.com/converting-9xr-to-frsky-telemetry-djt-module-t362.html Actual http://openrcforums.com/wiki/index.php/9x_Full_Mod_FrSky How recently did you buy it? About one year The mo...

Hi ,

Any clue?

I have already do a new flash to the TX with New version and the problem still there...

Hi João,

Yes, i have connect two lines. RX and Tx .

Hi,

This New version still dont keep Tssi and Rssi values. When i turn of the radio this values are erased.

Please try same in Vimeo

[BBvideo 425,350]https://vimeo.com/63777874[/BBvideo]

Link to the video

[quote][http://m.youtube.com/#/watch?v=WxoPCHDKMJ4

Make this clip

[BBvideo 425,350]http://m.youtube.com/watch?v=WxoPCHDKMJ4[/BBvideo]

Hi, I have connect both TX and RX that's why I can interact with the module. I can actually raise or lower the sensitivity of RSSI and TSSI being the beeps increase decrease or disappear whichever I'm introducing in the radio. So far so good. When I turn off the radio the values ​​of the radio disap...

:D Good to know Ok, I get it working and tested. I refer now to the frsky TX alarms . I can interact with the module and lower the sensitivity of RSSI and TSSI to decrease the beeps as I want. However, when I turn off the radio andget it on again this programming disappears and TX return to factory ...

João you are the man.

You are right, tested and works

What about Tssi and Rssi values that doesn´t stay at the when shwitch off.

By the way, João is a Portuguese name, isn´t it?

Yes, put in line 470ohms resistor

Hi, I am running R788 in a 9XR I made a modification to the Frsky and is working well. I do not understand why when I turn off the radio they lose the values ​​programmed into the RSSI TSSI. Once again I turn on the radio, the values ​​are zero and the TX module return to the factory settings. The v...

Thank you all.

Such a dummy I´am ...

Everthing is clarified now and working . I´m driving a haptic motor whith a BC548 directly from pin 43.

Thanks again

Silvio Semedo

Already works, i think...

I've reflash ER9X with a another PC.

Now reading voltage between positive from regulator 5V and Pin 43 is now 5v in normal mode and in alarm 0V.

Don't be oposite way? 5V in alarm and 0V in standby mode?

No, in the second radio i only mesure whith mutimeter. Another test. Check continuity between the ground of the atemega and the pin 43, and whith radio off is infinite (open). When I turn the radio down to 18 ohms. If burnt will does not be influenced of this way only because the Atmega powered or n...

It's a 64.

Probably you have reason, however I find it strange two different radios have the same behavior...

Thanks for your quick reply

The test with the led was a desperate measure.

Before I was only measured with the multimeter whith a 1K resistor between pin # 43 and the positive battery.

Do not forget what I did the same test on another radio and it's the same thing.

Two burn atmega!!??

At the moment I have only one led to a resistance of 470 ohms with the negative on pin #43, and positive to V+.

There is not a residual voltage.

I have tried in another 9XR and is the same thing.

Already separated the pin from the board, (could be grounded) and the led still light

Hi,

One help here please ,

My #43 Pin is always on (11volts) , and dont changing this status. I am running r788 er9x on my Turnigy 9XR.

Try to change to open tx and is the same thing.

I have no more ideas....

Ok this solution is working until now. I just put 4 1k resistor just like you show in the other post.

Still working Abukede?