openrcforums

magnetus

does anyone knows if this rotary encoder works in an 9x with a 9xtreme board installed?

magnetus

indicates a tolerance of "K" of 10% , "F" 1% and "J" of 5%

magnetus

I have both 9X and 9XR (non-Pro). and I like the 9XR better. it feels better too.

magnetus

pm sent

magnetus

is it there the possibility to have a "kit" without soldered connectors? or the connectors will be soldered at the manufacture process, I am planning to use mine with my 9XR....

magnetus

(((So DJT and XJT all working)))
Will the 9Xtreme board be able to handle DSM2/DSMX, UHF and FASST protocols ?

magnetus

Mike thanks for your hard work. I know this is in the early stages still but is it there a possibility to upgrade the LCD screen, maybe in a DIY transmitter, to a 212x64 pixels or anything different than the stock LCD Display. Also is there going to be LUA support for this product? thanks again. Mig...

magnetus

Just posted new test versions. 1. '128/'2561 include 1-shot and 1-shotR as functions in the extra 6 logical switches. 2. All versions include ONCE and ALL as rate options in voice alarms. ONCE plays the voice file once when a model is loaded (therefore include a startup). ALL is for use by 3-positi...

magnetus

STM32F4xx devices have Real Time Clock (RTC) inside, with support of internal calibrated 32768 Hz oscillator or external (more accurate) 32768 Hz oscillator. RTC peripheral has also backup register support, which means that when you reset MCU, registers are not reset or if power is off and you have ...

magnetus

take my money.... I want one... or two.... lol

magnetus

here is the chip datasheet: hxxp://www.st.com/st-web-ui/static/active/en/r ... 237391.pdf
and an alternate: hxxp://www.st.com/st-web-ui/static/active/en/r ... 263874.pdf

magnetus

I do too have 2 9x radios. I started to mod 1 with arduvoice (previous a megasound but never worked), I ordered some pcb for rotary encoder that are on their way already , I have a m128 and backlight installed. this radio also have a removable rf module and I have an orange, a DHT and the original t...

magnetus

Well done.. If you build the strip board you have to pay attention to the fact that the arduino has A4 and A5 on an different place.. Probably just solder the resistors from the arduino (A4, A5) directly to the strip where pin 2 of the LM386 is soldered. Will try to have a look tomorrow. I'm buildi...

magnetus

magnetus wrote:got an sd card adapter from ebay and an arduino pro mini (this one has A5 & A6 relocated). loaded arduvoice files Boot & Firmware from first post. and its alive.
I still dont know why my megasound board doesnt work.
still need to add filters, backlight and beeper.

magnetus

got an arduvoice module to work (arduino pro mini + sd card reader + lm386). i dont know why my megasound board does not work. i think i will give up on it and keep working with my arduvoice. still need to add filters, backlight and beeper.

magnetus

got an sd card adapter from ebay and an arduino pro mini (this one has A5 & A6 relocated). loaded arduvoice files Boot & Firmware from first post. and its alive. still need to add filters, backlight and beeper.
I still dont know why my megasound board doesnt work.

magnetus

reroute the trim switches using PC0 and LCD_WR, you can replace them by EXT3 and EXT4 options on the 3-POS option list make haptic available on one of the voice module to have the extra switch pin connected to a mainboard processor pin if available great ideas !!!! I think we can access bootloader m...

magnetus

can a FM24C256 or MB85RC256V serial RAM be implemented?
this particular cases are 256k (32kx8) and is an I2C device
also how about a AT24C256 for extra eeprom space.

magnetus

just a little mistake in the PDF.
D1 twice. should be D1, D2
Diodes
D1 Schotky-diode small, BAT85, 1N6263,.....
D1 Schotky-diode small, BAT85, 1N6263,.....

magnetus

jhsa wrote:To replace trainer with a normal switch you can do it already. You don't need any firmware option for that..

João

great I just read it in the manual also you can assign any function to it.

magnetus

so we will have the options to use PC0, PG2, PA0, PA1, PA2, PA3 and PB7 on the 9x and LCD2, LCD3, PB7 and the lines you call X1, X2 and X3.
how much memory or how hard will be to replace RUD, ELE, AIL, GEAR with 3 ways switches and replace trainer with a switch.
it will feels more like my DX9....

magnetus

As you probably have read on the forum Mike is implementing a serial communication between the voice module and the radio instead of using the LCD lines and the CLK signal. For that to happen the throttle trims must be connected to the voice module. That is an easy operation. Just removing two wire...

magnetus

thanks guys. im am thinking of build a "modular" arduvoice board. more than willing to share with you guys. I am thinking of using a cheap lm386 board from ebay. as jhsa mentioned earlier, pin 2 is attached to GND, so I was thinking that we might be able to use a resistive passive mixer co...

magnetus

this schematic is fairly easy to understand but I have a few questions. the lm386 audio amp seems to be used as differential amplifier using R10/R4 as voltage divider for the invert input (pin2) and R8/R9 as voltage divider for the non-inverted input (pin3). beeper sound is amplified by the inverted...

magnetus

nothing connected to pin 3. ohm out the pins and no shorts

magnetus

getting 3.22 powered from my transmitter and 4.78 powered from the usbasp.
the previous voltages were read powered by the 9x regulated from the 3.3 v regulator.
powered from usbasp i have 4.78 at pin 2 and 0 at pin3

magnetus

iteadstudio seems to be cheaper 10+2 CCAs for 9.90. does anyone knows how to order from them>? just ordered from iteadstudio 10cca + got 2 free for been open source. andrewju, i will check shipping to Russia, if the price of shipping is not that much i will send you one. do you have any postal code...

magnetus

The only difference between the 328 and the 328P is the P stands for "picoPower", so the processor uses slightly less power. I've just realised that the option of typing '1' to '9' in the test vesion only works if it is the parallel version, they don't work in the serial version. I'm tryi...

magnetus

thanks for the offering. how do you order from those places. if you can post the files I will look at the prices here and order some if is convenient for me and share with anyone in this side of the world.

magnetus

I want to mod my spare 9x with a '2561 but also will like to install a rotary encoder. I emailed hipo and he is no longer fabricating those pcb. does anyone has a spare pcb???
I will order the encoder and the chips from mouser or digikey

openrcforums

Search found 93 matches

Re: Sky9x Rotary Encoder Option

Re: Help, Burned Caps

Re: 9Xtreme Upgrade Board for 9x Radios

Re: 9Xtreme Upgrade Board for 9x Radios

Re: 9Xtreme Upgrade Board for 9x Radios

Re: 9Xtreme Upgrade Board for 9x Radios

Re: 9Xtreme Upgrade Board for 9x Radios

Re: er9x development

Re: Arduino Due add on to 9X

Re: Arduino Due add on to 9X

Re: Arduino Due add on to 9X

Re: Arduino Due add on to 9X

Re: ArduVoice-9x Voice Module with Arduino for the 9x Radio

Re: ArduVoice-9x Voice Module with Arduino for the 9x Radio

Re: Audio (voice) - Stock 9X PCB --=UPDATE=--

Re: ArduVoice-9x Voice Module with Arduino for the 9x Radio

Re: er9x development

Re: er9x development

Re: ArduVoice-9x Voice Module with Arduino for the 9x Radio

Re: er9x development

Re: er9x development

Re: ArduVoice-9x Voice Module with Arduino for the 9x Radio

Re: ArduVoice-9x Voice Module with Arduino for the 9x Radio

Re: ArduVoice-9x Voice Module with Arduino for the 9x Radio

Re: Audio (voice) - Stock 9X PCB

Re: Audio (voice) - Stock 9X PCB

Re: Sky9x Rotary Encoder Option

Re: Audio (voice) - Stock 9X PCB

Re: Sky9x Rotary Encoder Option

Re: er9x development