openrcforums

Thx for the answer

Hi there, I wonder if it is possible to get the telemetry Screen right on powering up the transmitter?

My fault!
Seems like I messed something up with the connections.
I opened it up, checked everything, took it back together and now it works

Hi there, I modified my DJT to get telemetry on Screen. This works fine, but the voltage alarms are not set any more, this worked fine in the past.
Is there a Problem with openTX >2.0?

Hi there, I was just testing around a bit, USB connected, disconnected it and there it goes, the Display is very weak now!
With contrast at 45, without backlight it is impossible to read, with backlight it's very dfficult.
What happened?
Wrting the Firmware doesn't change anything

Thank you for this information

And a dx5 module? I think it's 6 channels too?

Is it limited by the Taranis or by the module itself?

Just a quick question I didn't find an answer to:
If I take a module form a DX4, will it transmit 8 channels?

Hey, here is my Setup for the Msr X, Sticky Throttle Cut on SF, some Expo and D/R on SD and a curve to counteract the roll drift on yaw.
Counter only counts when Motor channel is armed.
I am using it with an Orange Module.
Have fun

That's easy, if you would use 60% Thr and 60% Ele on CH1, you would exceed 100% on full pitch and full nick backwards (120%). This would cause some serious Problems because all servos are mechanically connected by the swashplate and the one on CH3 would try to travel more distance then the one on CH...

Just like this:
Just your Imagination is the Limit

Blade Msr X

I don't udnerstand why I can't use Max and this makes things more difficult (I think)...

- Just make a new model
- Remove all Mixers
- Add a Max 100, any Switch to activate it, Slow Up ... (5, 7, 10, doesn't matter)

Wirks only once, you have to restart the Transmitter that it will work again.

Hi, tried to use Slow Up only, there seems to be a bug:
It works only one time, then it is deactivated until I restart the transmitter.

Set Trainer to slave under model setup and you're good to go

That will do it
Bound a D4, D8 and two D6 in that way to the Taranis.

rperkins wrote:You know after making the change it wont work as a usbasp any more ?

Yes of course I know it
I am looking for a cheap solution to have an 8 channel (at least) PPM2USB Interface.

Hi I modified a usbasp to allow this code to run. Had to cut one trace and solder one jumper wire. Last night I got as far as plugging it into the computer and it was recognized as a 'HID joystick' or something like that. I'd like to test it tonight. What simulator did you use ? Do you know of a fr...

Key to success is good Hardware, if the sticks are c**p, it's not important how low the Price is since this has alot of Features!

Yes, already said that it works now
I forgot about it... Sequencial and cyclic...

Ah yes, that's it... Makes sense

I just fooled around a little bit and found something strange. I would like to have my models spoken at the beginning (custom functions with Argument ONE). So it starts up, tells me first that the motorchannel is inactive, then in which mode my gyro is and THEN it tells me what model I've selected. ...

The Startup Sound is located in Sounds/en/System/tada.wav.
The files need to be 8, 16, or 32kHz saved in A-Law or U-Law.

Hi, a friend of mine got his new Orange RX Module, seems to work with his mcpx, but it always binds up using DSMX.
Since there seems to be some issues with DSMX and the Orange module, is there a way to force it into DSM2?

That's what I'm doing on my Bixler, but that is not what he asked for

You Need a voltage divider if you want to use voltages higher then 3.3V.
The intern voltage divider is Ratio 4 to 1, so 4 * 3.3 = 13.2. If you put in 13.2 the voltage divider puts out 3.3, so 13.2V is Maximum for 4:1.
You can build your own voltage divider with 2 resistors and one capacitor.

You have to set the range of A1 and A2.
For example if you use the internal voltage sensor for A1 you have to set it to 13.2V.
It's working because you have RSSI
And remember: never put higher voltages then 3.3V on A1 or A2.

Hi there, I'd like know some facts about using other branded Radios as Trainer Transmitter.
I don't know if it is the way like it is on the 9X, if the voltage is low (like Spektrum) it simply doesn't work.
And what if the voltage is rather high? Could this do damage to the Taranis?