Search found 11 matches
- Wed Apr 03, 2013 11:58 pm
- Forum: PROGRAMMERS
- Topic: 9XR Firmware burn failed
- Replies: 37
- Views: 40885
Re: 9XR Firmware burn failed
Yes the chip was installed in the radio all the time. To desolder and replace the chip would have been my next step if the oscillator had doesn´t worked. But.....to desolder a 64 pin qfp seems not be funny..without the right tools... No, you have nothing to disconnect from the mainboard of the turni...
- Wed Apr 03, 2013 8:37 pm
- Forum: PROGRAMMERS
- Topic: 9XR Firmware burn failed
- Replies: 37
- Views: 40885
Re: 9XR Firmware burn failed
You will need something like that: http://www.conrad.com/ce/en/product/158119/Quarzoszillator-Serie-TFT-680-TFT680-Frequenz-8-MHz-Bauform-DIP-14-L-x-B-207-mm-x-131-mm;jsessionid=5E6F781B6942239737852EE29F33E2F8.ASTPCEN08 In this case you have to connect pin 14 to +5V , pin 7 to GND and pin 8 is the ...
- Wed Apr 03, 2013 12:53 pm
- Forum: PROGRAMMERS
- Topic: 9XR Firmware burn failed
- Replies: 37
- Views: 40885
Re: 9XR Firmware burn failed
Hi, you will need a oscillator not a crytal. Or something else thats able generate a suitable clock like the arduino in the Post linked by rperkins above with the right voltage. Because the AtMega is (mis)configured to use a external clock not a crystal(which is onboard). The value should doesn´t ma...
- Tue Apr 02, 2013 7:38 pm
- Forum: PROGRAMMERS
- Topic: 9XR Firmware burn failed
- Replies: 37
- Views: 40885
Re: 9XR Firmware burn failed
Hi all, today i received my HK programmer..after nearly a month...and i immediately tried to flash my 9xr. But without luck. The same error like with the other programmer...Target didn´t answer. So i decided to try it with an external clock source and pulled the mainboard out of the 9xr. I used a 8 ...
- Sat Mar 09, 2013 11:31 am
- Forum: PROGRAMMERS
- Topic: 9XR Firmware burn failed
- Replies: 37
- Views: 40885
Re: 9XR Firmware burn failed
finally got an answer from the HobbyKing Support...but...without good news. No Board(s) availiable from Hobbyking. Hmmm, can´t see any resistors near F1. There are four parts in sum near F1 including F1. The quartz crystal,F1 and two red looking things :P Maybe Diods? On the other side of the progra...
- Wed Mar 06, 2013 4:18 pm
- Forum: PROGRAMMERS
- Topic: 9XR Firmware burn failed
- Replies: 37
- Views: 40885
Re: 9XR Firmware burn failed
hi all, thanks for your reply. For now it seems that my last chance is to wait until the programmer from Hobbyking arrives without doing some modifications to my 9xr. Maybe there are problems with some resistors on my current progammer, too. the next step after that , i guess, would be to provide an...
- Tue Mar 05, 2013 4:38 pm
- Forum: PROGRAMMERS
- Topic: 9XR Firmware burn failed
- Replies: 37
- Views: 40885
Re: 9XR Firmware burn failed
"-B 100" does not work either
i have tried it with linux(gentoo kernel 3.2.12) and windows 7 with the 5.11 Version of avrdude
i have tried it with linux(gentoo kernel 3.2.12) and windows 7 with the 5.11 Version of avrdude
- Tue Mar 05, 2013 2:06 pm
- Forum: PROGRAMMERS
- Topic: 9XR Firmware burn failed
- Replies: 37
- Views: 40885
Re: 9XR Firmware burn failed
Hi, Yes i changed the settings in companion9x to use an arduino as ips. But i have read that i have to use the "avrisp" with an arduino too. I also tried eePe but it doesnt work too. So i tried to upload the hex file with avrdude direcly..but without success. (what is basicly the same what...
- Sun Mar 03, 2013 2:01 pm
- Forum: PROGRAMMERS
- Topic: 9XR Firmware burn failed
- Replies: 37
- Views: 40885
Re: 9XR Firmware burn failed
it also doesn´t work whit the new arduino versions. 1.03 and the beta version 1.5.2
its allways not in sync
its allways not in sync
- Sat Mar 02, 2013 9:13 pm
- Forum: PROGRAMMERS
- Topic: 9XR Firmware burn failed
- Replies: 37
- Views: 40885
Re: 9XR Firmware burn failed
Hi Rob thanks for your replay. that one that i have is the same one like that one on "9xrprogrammers.com". If i compare the pictuers with mine. But mine is from ebay. is it that one from HobbyKing: http://www.hobbyking.com/hobbyking/store/__21321__USBasp_AVR_Programming_Device_for_ATMEL_pr...
- Sat Mar 02, 2013 7:47 pm
- Forum: PROGRAMMERS
- Topic: 9XR Firmware burn failed
- Replies: 37
- Views: 40885
9XR Firmware burn failed
Hi all, I have a big problem with my 9XR. Today i flashed..or wanted to flash my 9XR with open9x with a usbasp like in the Video: https://www.youtube.com/watch?v=x_yDfl7fuSw Everything went fine exept at the end of the verify part. There was an errormessage that the first byte(s) are not correct. Or...