Search found 89 matches

by willhac
Sat Sep 30, 2017 7:34 am
Forum: 9Xtreme upgrade board
Topic: flashing avr multi with 9xtreme maintenance mode
Replies: 15
Views: 2284

Re: flashing avr multi with 9xtreme maintenance mode

My modules are updated and the radio is ready for flying, so don't look at it if it takes too much time. I'm not sure I will flash the internal module so often ! Thank you both for your help Edit : I found what happened : a second led and resistor was added to see the status led at the back of the r...
by willhac
Fri Sep 29, 2017 9:04 pm
Forum: 9Xtreme upgrade board
Topic: flashing avr multi with 9xtreme maintenance mode
Replies: 15
Views: 2284

Re: flashing avr multi with 9xtreme maintenance mode

I can't see 1.1.6.21 beside the bind option...
If I flash the same file with the ISP the led stays solid (I can control a model) and I can see 1.1.6.21.

My external module is with board 2.3c, and the internal is with an arduino pro mini, does it make a difference ? Fuses are the same with D6 at H.
by willhac
Fri Sep 29, 2017 3:46 pm
Forum: 9Xtreme upgrade board
Topic: flashing avr multi with 9xtreme maintenance mode
Replies: 15
Views: 2284

Re: flashing avr multi with 9xtreme maintenance mode

Now flashing works well with the external module on second and further attempts. :D

Still the same with the internal one, it seems it doesn't program, despite this message :

0000 0000
Flashing Complete
1E95 0F10 0000 0000 0000
by willhac
Fri Sep 29, 2017 9:21 am
Forum: 9Xtreme upgrade board
Topic: flashing avr multi with 9xtreme maintenance mode
Replies: 15
Views: 2284

Re: flashing avr multi with 9xtreme maintenance mode

OK I was downloading the code from here : https://github.com/pascallanger/DIY-Multiprotocol-TX-Module where the "CHECK_FOR_BOOTLOADER" code is not included. As far as I understand I don't need the bind button. I'll try again this evening. Strange for the 43Ko file (size of .hex file in windows, not ...
by willhac
Fri Sep 29, 2017 7:11 am
Forum: 9Xtreme upgrade board
Topic: flashing avr multi with 9xtreme maintenance mode
Replies: 15
Views: 2284

Re: flashing avr multi with 9xtreme maintenance mode

I can't find "CHECK_FOR_BOOTLOADER", is it a line to comment/uncomment ? in _config.h ? ...and also I don't have any bind button connected. Do I need it for flashing in maintenance mode ? If yes when do I press it ? My hex files are 29 Ko and 43Ko with just the protocols needed, so they should leav...
by willhac
Thu Sep 28, 2017 10:34 pm
Forum: 9Xtreme upgrade board
Topic: flashing avr multi with 9xtreme maintenance mode
Replies: 15
Views: 2284

Re: flashing avr multi with 9xtreme maintenance mode

I can't find "CHECK_FOR_BOOTLOADER", is it a line to comment/uncomment ? in _config.h ?
by willhac
Thu Sep 28, 2017 9:45 pm
Forum: 9Xtreme upgrade board
Topic: flashing avr multi with 9xtreme maintenance mode
Replies: 15
Views: 2284

flashing avr multi with 9xtreme maintenance mode

Hi guys, I'm trying to get back in the hobby after a period of inactivity, so a good start is to update everything ! 9xtreme now has the latest test version, the bootloader is updated. It has an external avr multi module, and an internal one : I compiled hex files and uploaded them with ISP -> every...
by willhac
Tue Mar 22, 2016 7:34 pm
Forum: erskyTx (was ersky9x)
Topic: ERSKY9X Coding
Replies: 4497
Views: 414418

Re: ERSKY9X Coding

Yes I confirm it's OK, thanks again Mike
by willhac
Mon Mar 21, 2016 7:27 pm
Forum: Hardware
Topic: New bug possibly discovered on 9x ("pot no. 3 bug")
Replies: 77
Views: 8885

Re: New bug possibly discovered on 9x ("pot no. 3 bug")

MikeB wrote: The JTAG port is only enabled one of the fuses is programmed to a 0. It is bit 6 of the fuse HIGH byte.

Mike.
So is it safer to set the high fuse to C1 ? (eepe sets it to 81)
by willhac
Mon Mar 21, 2016 7:18 pm
Forum: erskyTx (was ersky9x)
Topic: ERSKY9X Coding
Replies: 4497
Views: 414418

Re: ERSKY9X Coding

OK, thanks
by willhac
Mon Mar 21, 2016 5:52 pm
Forum: erskyTx (was ersky9x)
Topic: ERSKY9X Coding
Replies: 4497
Views: 414418

Re: ERSKY9X Coding

@Mike : I'm testing the internal MULTI with the 9Xtreme, my setup is : - internal MULTI with A7105 (Flysky modified) - external MULTI with NRF24L01 & CC2500 I noticed that when I switch from a model using external module to a model using internal module the LED of internal MULTI blinks slowly (no va...
by willhac
Wed Mar 16, 2016 7:19 pm
Forum: erskyTx (was ersky9x)
Topic: ERSKY9X Coding
Replies: 4497
Views: 414418

Re: ERSKY9X Coding

I tried it with a wltoys F929/939 board that needs autobind, it works great :)
Just a small display bug when going down to the line "External ON/OFF" : Type-Autobind-Power not displayed.
by willhac
Tue Mar 15, 2016 10:19 pm
Forum: erskyTx (was ersky9x)
Topic: ERSKY9X Coding
Replies: 4497
Views: 414418

Re: ERSKY9X Coding

Thanks Mike,
I have a "multi" modified Flysky module inside my 9xtreme radio, it actually works with PPM.
I will "serial" test it as soon as a test version will be available.
by willhac
Sun Mar 13, 2016 7:23 pm
Forum: erskyTx (was ersky9x)
Topic: ERSKY9X Coding
Replies: 4497
Views: 414418

Re: ERSKY9X Coding

Any news about supporting MULTI as internal module of the 9xtreme ?
With all the protocols It implies too much constraints perhaps ?

(...and do others need it except me ! :mrgreen: )
by willhac
Fri Feb 26, 2016 11:17 pm
Forum: 9Xtreme upgrade board
Topic: My 9Xtreme Installation
Replies: 212
Views: 45710

Re: My 9Xtreme Installation

Yes and it's a good solution, but I didn't install the Taranis gimbals, I'm ok with the stock gimbals. :mrgreen:
So I use the 5 pin JST plug that comes with the Taranis sliders !
by willhac
Fri Feb 26, 2016 10:49 pm
Forum: 9Xtreme upgrade board
Topic: My 9Xtreme Installation
Replies: 212
Views: 45710

Re: My 9Xtreme Installation

The Taranis sliders are supplied with a 5 pin connector.
If you don't need all the connections you can use it, it even allows a connection for a 3 pos switch for exemple ;)
by willhac
Fri Feb 19, 2016 12:06 pm
Forum: 9Xtreme upgrade board
Topic: How to create your own voice recordings?
Replies: 6
Views: 1502

Re: How to create your own voice recordings?

Hi,
I use Balabolka with Microsoft Speech Platform :
http://www.cross-plus-a.com/balabolka.htm
...and after I use Audacity to modify the files.
by willhac
Sun Jan 03, 2016 8:54 pm
Forum: erskyTx (was ersky9x)
Topic: ERSKY9X Coding
Replies: 4497
Views: 414418

Re: ERSKY9X Coding

MikeB wrote:ersky9xProvR218j on the 9Xtreme should support using COM1, via a software serial driver, for the MULTI telemetry, as does COM1 on a SKY/AR9X board when using inverted input hardware.

Mike.
I didn't know we could already use it ! :)
It works fine.
by willhac
Sun Jan 03, 2016 6:34 pm
Forum: erskyTx (was ersky9x)
Topic: ERSKY9X Coding
Replies: 4497
Views: 414418

Re: ERSKY9X Coding

Good !
by willhac
Sun Jan 03, 2016 6:20 pm
Forum: erskyTx (was ersky9x)
Topic: ERSKY9X Coding
Replies: 4497
Views: 414418

Re: ERSKY9X Coding

For ersky9x : ersky9xProvR218j.zip (31-Dec-2015 - the last version for 9Xtreme)
For Multi : the same as yours (Multi 02-01)
by willhac
Sun Jan 03, 2016 5:58 pm
Forum: erskyTx (was ersky9x)
Topic: ERSKY9X Coding
Replies: 4497
Views: 414418

Re: ERSKY9X Coding

As soon as it is ready I will post on multi thread. Thanks ! From what I understand Kaos has the ar9x board (replacement board for tgy9x), I have the 9Xtreme (add-on board for the tgy9x). Both use ersky9x but maybe there are hardware differences. I use COM2 for the telemetry on the 9Xtreme, which i...
by willhac
Sun Jan 03, 2016 12:40 pm
Forum: erskyTx (was ersky9x)
Topic: ERSKY9X Coding
Replies: 4497
Views: 414418

Re: ERSKY9X Coding

Sounds like a problem with the Multi firmware. Mike. I believe that the last version of multi module firmware posted on Github is not ready for FrSky Hub protocol yet : with the 9Xtreme/Multi/COM2/R218j : TmOK is at 1 with the last multi module firmware (A1-A2-RSSI-TSSI are OK) If I flash the (olde...
by willhac
Sun Dec 27, 2015 9:55 am
Forum: erskyTx (was ersky9x)
Topic: ERSKYTx (was ersky9x) Questions
Replies: 1968
Views: 290989

Re: ERSKY9x Questions

With 9Xtreme : just connect the telemetry output of the multi module directly to COM2-RX, it works. ;) (already non-inverted signal)
by willhac
Tue Dec 22, 2015 7:24 pm
Forum: erskyTx (was ersky9x)
Topic: ERSKY9X Coding
Replies: 4497
Views: 414418

Re: ERSKY9X Coding

Yes, it's the test version Midelic posted here : http://www.rcgroups.com/forums/showthread.php?t=2165676&page=148 My setting are : UsrProto : FrSky COM2 : telemetry baudrate is forced by MULTI as Mike explained above. I did a few ground range tests today with it, it seems quite the same with the DJT...
by willhac
Mon Dec 21, 2015 7:42 pm
Forum: erskyTx (was ersky9x)
Topic: ERSKY9X Coding
Replies: 4497
Views: 414418

Re: ERSKY9X Coding

...and you fixed it, bravo !
Telemetry is now working, the error counter stays at 0.
Will try some sensors later...
by willhac
Mon Dec 21, 2015 6:05 pm
Forum: erskyTx (was ersky9x)
Topic: ERSKY9X Coding
Replies: 4497
Views: 414418

Re: ERSKY9X Coding

@Mike (no telemetry) :
Numbers on the first 2 lines :
0000 012C 242C 0000
0000 0000 xxxx
xxxx=number always incrementing
FIFO buffer : all at 0
by willhac
Mon Dec 21, 2015 3:55 pm
Forum: erskyTx (was ersky9x)
Topic: ERSKY9X Coding
Replies: 4497
Views: 414418

Re: ERSKY9X Coding

Just checking (probably correct from before), you do have "FrSky COM Port" set to 2? Mike. Yes it's set correctly to 2. (I noticed that when UsrProto is changed, "FrSky COM Port" is forced back to 1) I also reflashed the 9Xtreme with dec.15th version to check, and the multi board with older multipr...
by willhac
Sun Dec 20, 2015 11:49 pm
Forum: erskyTx (was ersky9x)
Topic: ERSKY9X Coding
Replies: 4497
Views: 414418

Re: ERSKY9X Coding

It's the same with "FrHub", no values.
For the info I didn't change the previous settings : COM2 func. = telemetry and COM2 baudrate = 115200, I suppose it's overriden ?
by willhac
Sun Dec 20, 2015 9:39 pm
Forum: erskyTx (was ersky9x)
Topic: ERSKY9X Coding
Replies: 4497
Views: 414418

Re: ERSKY9X Coding

It's connected on COM2.
Telemetry was working fine with the test version that fixed the reboot bug with MULTI/COM2 on the 9Xtreme.
by willhac
Sun Dec 20, 2015 9:16 pm
Forum: erskyTx (was ersky9x)
Topic: ERSKY9X Coding
Replies: 4497
Views: 414418

Re: ERSKY9X Coding

I just tested the 9Xtreme test version for the new multi protocol format.
I flashed the multi board with the file posted today on RCgroups.
Tested OK with a Flysky and a Frsky receiver (not 16 channels...)
But no telemetry with Frsky, not implemented yet ?

Go to advanced search