Search found 83 matches
- Fri Oct 23, 2015 3:02 pm
- Forum: FrSky Taranis radio
- Topic: Taranis X9D does not turn on after a 2.1.3 update
- Replies: 7
- Views: 6543
Re: Taranis X9D does not turn on after a 2.1.3 update
For the moment, i could put the 2.0.17 firmware or even 2.1.3 firmware, copying the firmware in the Taranis sd folder "FIRMWARE" it works..... but in both cases, my "models file" i save before my problem does not looks compatible! i realy don't know how to make it go right.... is...
- Fri Oct 23, 2015 12:48 pm
- Forum: FrSky Taranis radio
- Topic: Taranis X9D does not turn on after a 2.1.3 update
- Replies: 7
- Views: 6543
Re: Taranis X9D does not turn on after a 2.1.3 update
i have a bootloader 2.0.5
- Fri Oct 23, 2015 12:44 pm
- Forum: FrSky Taranis radio
- Topic: Taranis X9D does not turn on after a 2.1.3 update
- Replies: 7
- Views: 6543
Re: Taranis X9D does not turn on after a 2.1.3 update
A taranis plus???
i think i have just a normal Taranis....
i think i have just a normal Taranis....
- Fri Oct 23, 2015 12:02 pm
- Forum: FrSky Taranis radio
- Topic: Taranis X9D does not turn on after a 2.1.3 update
- Replies: 7
- Views: 6543
Re: Taranis X9D does not turn on after a 2.1.3 update
i find this: Attention! I found a solution to my totally dead Taranis X9D Plus after wrong firmware install. It would not power up with the switch. It would not go to the boot loader with the three switch method. No flicker on the screen or anything. It was dead except for a faint hiss over the spea...
- Fri Oct 23, 2015 11:15 am
- Forum: FrSky Taranis radio
- Topic: Taranis X9D does not turn on after a 2.1.3 update
- Replies: 7
- Views: 6543
Taranis X9D does not turn on after a 2.1.3 update
Hello,
I tried to update the firmware of my Taranis X9D to 2.1.3.
Everything was ok. but one time I turned the TAranis off, then it will never turn ON again!!!!
Does it exist a "rescue" procedure?
best regards!
I tried to update the firmware of my Taranis X9D to 2.1.3.
Everything was ok. but one time I turned the TAranis off, then it will never turn ON again!!!!
Does it exist a "rescue" procedure?
best regards!
- Fri Mar 27, 2015 2:57 pm
- Forum: FrSky Taranis radio
- Topic: Taranis BAttery connector
- Replies: 2
- Views: 3266
Re: Taranis BAttery connector
thank you!
- Fri Mar 20, 2015 2:16 pm
- Forum: FrSky Taranis radio
- Topic: Taranis BAttery connector
- Replies: 2
- Views: 3266
Taranis BAttery connector
Hello, In my Taranis, the battery connector is the same as a 2S lipo balancer. is it possible to connect directly a 2S lipo balancer. (the middle pin of the taranis, is not used with a standard battery, but can we connect a 2S lipo, as i don't know if the taranis will accept the +3,7V of the middle ...
- Mon Nov 10, 2014 10:24 pm
- Forum: FrSky Taranis radio
- Topic: Taranis TIME update
- Replies: 5
- Views: 3594
Taranis TIME update
Hello,
In my Taranis, i can see that the time is not very accurate.
Could it be possible to get the PC time update when we connect it to the PC?
it could be a nice feature..
regards
In my Taranis, i can see that the time is not very accurate.
Could it be possible to get the PC time update when we connect it to the PC?
it could be a nice feature..
regards
- Wed Oct 08, 2014 6:57 pm
- Forum: FrSky Taranis radio
- Topic: Taranis - memorizing a value
- Replies: 2
- Views: 3523
Taranis - memorizing a value
Hello,
Is it possible to memorize a value (telemetry altitude when cutting off throttle for example), a get this value on screen until the end of the flight?
regards
Benjamin
Is it possible to memorize a value (telemetry altitude when cutting off throttle for example), a get this value on screen until the end of the flight?
regards
Benjamin
- Fri Sep 26, 2014 8:40 pm
- Forum: openTx
- Topic: count down timer
- Replies: 4
- Views: 3581
Re: count down timer
Thank you very much!
you always help us, and very quickly!!!
this radio has so many possibilities! and i'm using very few things i think!
regards
Benjamin
you always help us, and very quickly!!!
this radio has so many possibilities! and i'm using very few things i think!
regards
Benjamin
- Fri Sep 26, 2014 7:53 pm
- Forum: openTx
- Topic: count down timer
- Replies: 4
- Views: 3581
Re: count down timer
Hello,
thanks a lot. for the moment i have the 10 last seconds with "bips", it's not so bad, but it would be interesting to get numbers!!!!
does someone know if the correction will be done?
regards
Benjamin
thanks a lot. for the moment i have the 10 last seconds with "bips", it's not so bad, but it would be interesting to get numbers!!!!
does someone know if the correction will be done?
regards
Benjamin
- Fri Sep 26, 2014 6:53 pm
- Forum: openTx
- Topic: count down timer
- Replies: 4
- Views: 3581
count down timer
Hello, When i use a count down timer on my taranis, i have all the minuts left then: 30s 20s 10s 10s 10s 10s 10s 10s 10s 10s 10s 10s bip looks like a bug! i tried on timer 1, and timer 2, or both.... all the same the same issue in French (but it's logical) is there is a way to get it works ? may be ...
- Mon Sep 22, 2014 2:23 pm
- Forum: FrSky Taranis radio
- Topic: TARANIS - battery
- Replies: 4
- Views: 4252
TARANIS - battery
Hello,
is it possible to use other battery in the Taranis?
Lipo 2S, Lipo 3S ?
what is the limitation?
also, in the battery case, there is another conector, does someone know what is for?
regards
Benjamin
is it possible to use other battery in the Taranis?
Lipo 2S, Lipo 3S ?
what is the limitation?
also, in the battery case, there is another conector, does someone know what is for?
regards
Benjamin
- Fri Sep 19, 2014 11:35 am
- Forum: FrSky Taranis radio
- Topic: TARANIS module Pin Out
- Replies: 2
- Views: 3752
Re: TARANIS module Pin Out
Thank you very much!
for the tip
for the tip
- Fri Sep 19, 2014 9:31 am
- Forum: FrSky Taranis radio
- Topic: TARANIS module Pin Out
- Replies: 2
- Views: 3752
TARANIS module Pin Out
Hello, in the place where we can add an external RF module in a taranis, there is some pins. where can i find what are they? i need to connect something wich need about 150mA at about 4 to 7V (i can need a regulador if voltage is too high). is it possible, and wich pin can be used? Thank you very mu...
- Wed Sep 10, 2014 9:09 am
- Forum: General help (FrSky Taranis radio)
- Topic: Low RSSI
- Replies: 91
- Views: 71312
Re: Low RSSI
hello, i have 3 F3K gliders, all full carbon except the nose where there is the receiver. they are all with D4R-II receiver antenas outside the nose ( and 90º ). so normaly it's a good orientation. for the moment, i'm using a T9X with DJT emisor. at about 100m altitude and 150-200m far, it's very of...
- Wed Sep 10, 2014 8:46 am
- Forum: FrSky Taranis radio
- Topic: Taranis - RSSI RX and TX
- Replies: 3
- Views: 3369
Re: Taranis - RSSI RX and TX
thanks.
any interest to use a DJT in a Taranis, or it's not usefull?
regards
any interest to use a DJT in a Taranis, or it's not usefull?
regards
- Mon Sep 08, 2014 9:31 pm
- Forum: FrSky Taranis radio
- Topic: Taranis - RSSI RX and TX
- Replies: 3
- Views: 3369
Taranis - RSSI RX and TX
hello, I'm near to pass from Turnigy 9X to my Taranis. i'm setting models, it's much more powerfull and interesting than the 9X!!! but in the Telemetry page, why it's not possible to get the RSSI TX on screen (only RSSI RX), when it was possible with a T9X? i'm using a standard Taranis with D4R-II r...
- Sat Jul 05, 2014 8:10 am
- Forum: Software
- Topic: Probs between Companion and Taranis
- Replies: 22
- Views: 20475
Re: Probs between Companion and Taranis
i have still the same problem.... can someone give me more explaination about this point? i did not find anything about that: 1.I deleted all the STM and and DFU mode drivers using the Windows Device Manager, ticking the box that said remove all files. i also tried a manual installation, but W8 said...
- Fri Jul 04, 2014 9:26 pm
- Forum: Software
- Topic: Probs between Companion and Taranis
- Replies: 22
- Views: 20475
Re: Probs between Companion and Taranis
hello, i think i have the same problem. i'm using open TXcompanion 2.05 a brand new taranis i can read the file of the radio (models) i can also upload it the radio, but after i have a eeprom problem (it must be formated) ... but i can't fin the way to send the last firmware to the radio. i have thi...
- Thu Apr 24, 2014 8:04 pm
- Forum: Turnigy 9XR radio
- Topic: RX Voltage with telemetry
- Replies: 4
- Views: 4195
Re: RX Voltage with telemetry
i tried again tonight.... and nothing.
i also realized that these receiver looks defective. under 5V, it does not want to work!!!
i also realized that these receiver looks defective. under 5V, it does not want to work!!!
- Thu Apr 24, 2014 10:07 am
- Forum: Turnigy 9XR radio
- Topic: RX Voltage with telemetry
- Replies: 4
- Views: 4195
RX Voltage with telemetry
Hello, i'm trying to get the RX voltage of my D4RII receptor in my T9X (open 9X) and i must do something wrong. the telemetry looks working as i can get RSSI on screen, and A2 voltage with the FBVS-01 voltage sensor. But now i want to get the RX voltage with a 1S lipo plugged on the RX. so i started...
- Fri Jan 31, 2014 7:37 am
- Forum: Hardware
- Topic: Taranis Gimals in a 9X
- Replies: 542
- Views: 278915
Re: Taranis Gimals in a 9X
For each gimball, you have one pot reversed. And one wich is ok.
- Thu Jan 30, 2014 10:54 pm
- Forum: Hardware
- Topic: Taranis Gimals in a 9X
- Replies: 542
- Views: 278915
Re: Taranis Gimals in a 9X
Im terribly sorry :( :( :( :D No issue... i use my 9X and 2 taranis gimball without any problem... and i have also the back light! With the amplified ones? Taranis Gimbals: #1 Red wire to Black wire 9x Radio Taranis Gimbals: #2 Orange wire to White wire 9x Radio Taranis Gimbals: #3 Brown wire to Re...
- Thu Jan 30, 2014 7:15 pm
- Forum: Hardware
- Topic: Taranis Gimals in a 9X
- Replies: 542
- Views: 278915
Re: Taranis Gimals in a 9X
i use my 9X and 2 taranis gimball without any problem... and i have also the back light!
- Thu Jan 30, 2014 5:12 pm
- Forum: Hardware
- Topic: Taranis Gimals in a 9X
- Replies: 542
- Views: 278915
Re: Taranis Gimals in a 9X
With amplifacadot
- Mon Jan 27, 2014 4:28 pm
- Forum: Hardware
- Topic: Taranis Gimals in a 9X
- Replies: 542
- Views: 278915
Re: Taranis Gimals in a 9X
Hello, can someone explane me why you need to change the 5V regulador? does the taranis gimball need more currrent? i have a T9X with telemetrez, back lite and taranis gimbal, and nothing special appear. i have another T9x, with smarties part board, telemetrez, back lite, and standard gimball, anoth...
- Fri Jan 10, 2014 1:14 pm
- Forum: Hardware
- Topic: Taranis Gimals in a 9X
- Replies: 542
- Views: 278915
Re: Taranis Gimals in a 9X
Hello, I get taranis gimbals to put inside my 9X. I received the Amplified potentiometer gimbals, so i had to find a solution for the reverse stick. finally i find that it's very easy to take off the potentiometer support of the gimball with a knife. http://img4.hostingpics.net/thumbs/mini_617819201...
- Wed Nov 13, 2013 10:29 pm
- Forum: openTx
- Topic: Count Down timer "bips"
- Replies: 48
- Views: 22979
Re: Count Down timer "bips"
Hello, i've just tried the R2834 firmware, and the count down bips are the same. the last 10 seconds are perfect, but the last bip of the count down is the same so it's difficult to apreciate the end of the programmed timer. And worst, the count down continue for each seconds as a negative time........
- Tue Sep 24, 2013 11:18 am
- Forum: openTx
- Topic: Count Down timer "bips"
- Replies: 48
- Views: 22979
Re: Count Down timer "bips"
ok, i understand, But there is really few difference between the kind of sound of the last beep when you reach the end of the count down, and the beeps you have when you passed the end of the count down. in several gliders competitions, you need to land at the EXACT end of the count down (and also a...