Search found 13 matches
- Tue Jul 28, 2020 2:14 am
- Forum: RF MODULES
- Topic: Orange Module running MULTI protocol
- Replies: 685
- Views: 427820
Re: Orange Module running MULTI protocol
Hi Mike, It loads the flash.app and then when I select update it asks me to select a file. Which is got from the https://downloads.multi-module.org/ site after selecting orange rx as the module type. when i select the file it goes through to the screen where is says delayed power on and then shortly...
- Sun Jul 26, 2020 6:42 pm
- Forum: RF MODULES
- Topic: Orange Module running MULTI protocol
- Replies: 685
- Views: 427820
Re: Orange Module running MULTI protocol
I'm using the download from https://downloads.multi-module.org/ for the green orange rx module. I bridged the r1 and r13. I'll re-try flashing using the bootloader with a fresh download of the firmware and see if that works.. If not oh well the module I ordered should be here in a day or so and it w...
- Sun Jul 26, 2020 6:08 pm
- Forum: RF MODULES
- Topic: Orange Module running MULTI protocol
- Replies: 685
- Views: 427820
Re: Orange Module running MULTI protocol
Hi Mike,
I felt like i was missing something.. I didn't bridge R1 and R13. I will do that. Do i need to re-write the bootloader? or should that just allow it to be flashed?
I felt like i was missing something.. I didn't bridge R1 and R13. I will do that. Do i need to re-write the bootloader? or should that just allow it to be flashed?
- Sun Jul 26, 2020 9:37 am
- Forum: RF MODULES
- Topic: Orange Module running MULTI protocol
- Replies: 685
- Views: 427820
Re: Orange Module running MULTI protocol
Hi Mike,
Thanks. I did try that but it said it failed to flash the module. I tried powering the system while holding the bind button and without. Each time failed.
the numbers at the bottom of the screen never changed from 0000 0000. I also tried inverted com and not.
Thanks. I did try that but it said it failed to flash the module. I tried powering the system while holding the bind button and without. Each time failed.
the numbers at the bottom of the screen never changed from 0000 0000. I also tried inverted com and not.
- Sun Jul 26, 2020 2:10 am
- Forum: RF MODULES
- Topic: Orange Module running MULTI protocol
- Replies: 685
- Views: 427820
Re: Orange Module running MULTI protocol
Hi Mike, I added some more debugging and all the reads I was doing were comming back with 0 bytes.. But the read of the header and fuses were working.. I messed around a bit and was able to get the bootloader flashed (confirmed as now when i hold the bind button the led on the module stays lit ) How...
- Tue Jul 21, 2020 4:00 am
- Forum: RF MODULES
- Topic: Orange Module running MULTI protocol
- Replies: 685
- Views: 427820
Re: Orange Module running MULTI protocol
It did flash correctly.Afterwards when it seemed like it didn't work I also modified the sketch a little bit to add some serial debugging and added some outputs for each stage of writing. and it hit each stage and output each message that it wrote to the device. but booting the module with the bind ...
- Fri Jul 17, 2020 8:28 pm
- Forum: RF MODULES
- Topic: Orange Module running MULTI protocol
- Replies: 685
- Views: 427820
Re: Orange Module running MULTI protocol
Hi Mike, Thanks for the information. I was able to get the sketch to work my pin outs were a little different. Pin 2 and 3 on the board did not work.. but i was able to get them to connect to the tx/rx pins and it was able to successfully run. but the board does not seem to operate any differently e...
- Thu Jul 16, 2020 6:27 am
- Forum: RF MODULES
- Topic: Orange Module running MULTI protocol
- Replies: 685
- Views: 427820
Re: Orange Module running MULTI protocol
Hi Mike, I have an Arduino mega 2560. This is the module I have. https://hobbyking.com/en_us/orangerx-dsmx-dsm2-devo-compatible-2-4ghz-selectable-transmitter-module-jr-turnigy-compatible.html I haven't done much yet. but based on some of what I've read it looks like I want put your sketch on the ard...
- Wed Jul 15, 2020 6:54 am
- Forum: RF MODULES
- Topic: Orange Module running MULTI protocol
- Replies: 685
- Views: 427820
Re: Orange Module running MULTI protocol
Thanks Mike.
I will go over the thread a little deeper and see if I can figure out how to get the bootloader loaded onto the module.
I will go over the thread a little deeper and see if I can figure out how to get the bootloader loaded onto the module.
- Mon Jul 13, 2020 9:13 pm
- Forum: RF MODULES
- Topic: Orange Module running MULTI protocol
- Replies: 685
- Views: 427820
Re: Orange Module running MULTI protocol
Is there a way to flash the orange rx module using open tx on a new QX7s Access radio?
or do i need to buy a programmer? and if i need a programmer which one is recommended and how does it get wired/powered.
or do i need to buy a programmer? and if i need a programmer which one is recommended and how does it get wired/powered.
- Sun Jul 22, 2018 2:15 am
- Forum: SMARTIEPARTS PROGRAMMER
- Topic: Smartiepartz board Rev 2.3 multi-module?
- Replies: 4
- Views: 9670
Re: Smartiepartz board Rev 2.3 multi-module?
Thanks. I'll have to look around for a 9xtreme board
- Fri Jul 20, 2018 2:56 am
- Forum: SMARTIEPARTS PROGRAMMER
- Topic: Smartiepartz board Rev 2.3 multi-module?
- Replies: 4
- Views: 9670
Smartiepartz board Rev 2.3 multi-module?
Its been so long since I've messed with my radio and I want to do a multi module setup.. Does anyone know if the smartiepartz board rev 2.3 can do multi module. I'd like to put the original module inside the receiver and be able to switch between that and a module I place on the back. This is for a ...
- Thu Jan 10, 2013 4:31 pm
- Forum: er9x
- Topic: Firmware and Module Question.
- Replies: 4
- Views: 3022
Firmware and Module Question.
Sorry if this is the wrong board to post this question to. (admin feel free to move it if needed) I'm modding my 9x and want to put er9x with telemetry in it. But I also plan on getting an orange Rx for dsm2/dsmx and was wondering if I would need to reflash everytime I changed the module? or would i...