Search found 2126 matches

by bob195558
Wed Sep 18, 2019 2:22 pm
Forum: Hardware Mods
Topic: Push buttons / Encoder
Replies: 32
Views: 3475

Re: Push buttons / Encoder

My son managed to delete my model in the radio, and for the life of me I cannot make this work again. Hi Rad, You are using erSkyTx firmware (http://www.er9x.com/), so you could use eepSkye to save a copy of all your model programs on your computer. You also can use eepSkye to edit or create each o...
by bob195558
Tue Sep 10, 2019 10:11 am
Forum: Hardware
Topic: FlySky Paladin Radio
Replies: 2
Views: 181

FlySky Paladin Radio

FlySky Paladin PL18 2.4GHz AFHDS3 18CH Radio System w/FTr10 and FTr16s FlySky Paladin Radio.jpg Another radio on the market. I like that the display screen at the top, but one other thing it needs is erSkyTx firmware. (https://hobbyking.com/en_us/flysky-paladin-pl18-2-4ghz-afhds3-18ch-radio-system-m...
by bob195558
Mon Sep 02, 2019 9:35 pm
Forum: General Information & Rules
Topic: FAA Unmanned Aircraft Systems Registration 2015 (FAA registrations are reinstated 2018)
Replies: 179
Views: 53084

Re: FAA Unmanned Aircraft Systems Registration 2015 (FAA registrations are reinstated 2018)

Hi Kilrah, I need your expert advice. Is this a real paypal email. From: [email protected].com â„¢ <[email protected].com> To: asfw4ehg.[email protected].com Subject: Take action on your PayPal account (Ref ID – PP059-9804354...
by bob195558
Mon Sep 02, 2019 11:27 am
Forum: openTx
Topic: Ailerons moving slow & with delay
Replies: 35
Views: 5749

Re: Ailerons moving slow & with delay

Hi Tomek,
You could try swapping your gimbals and see if the problem follows.
by bob195558
Sun Sep 01, 2019 11:31 pm
Forum: openTx
Topic: Ailerons moving slow & with delay
Replies: 35
Views: 5749

Re: Ailerons moving slow & with delay

Thank you Kilrah, I missed that part.
by bob195558
Sun Sep 01, 2019 12:55 pm
Forum: openTx
Topic: Ailerons moving slow & with delay
Replies: 35
Views: 5749

Re: Ailerons moving slow & with delay

Hi Tomek, Sounds like a hardware problem or maybe check your software settings that they have not somehow been changed. I have had a problem with the internal module on the older Taranis-x9d that it would randomly fail. The fix was, replacing the internal module. You may want to purchase an external...
by bob195558
Wed Aug 28, 2019 11:55 am
Forum: Hardware
Topic: FS-TH9X doesn'tturn on after ER9x flash
Replies: 20
Views: 562

Re: FS-TH9X doesn'tturn on after ER9x flash

You would then need to open up the case and read the top of the chip. Sounds like you may have a 64 then. Go here for your download: (http://www.er9x.com/). May be one of these unless you have other mods done: er9x standard (right click and select 'save as') or er9x for M64-FrSky (right click and se...
by bob195558
Wed Aug 28, 2019 10:27 am
Forum: 9Xtreme upgrade board
Topic: 9Xtreme being released to the public domain (opensource)
Replies: 40
Views: 7695

Re: 9Xtreme being released to the public domain (opensource)

Hi All, Sorry for the delayed reply, have been on holidays and flat out with work and not enough time for the toys. Over the weekend and next week I will look into getting some made and see what the price is going to look like, at least with a few people wanting might make my wallet feel a little n...
by bob195558
Sat Aug 24, 2019 12:50 am
Forum: Hardware
Topic: FrSky M9 gimbals in a 9x - photos (traffic!)
Replies: 108
Views: 22149

Re: FrSky M9 gimbals in a 9x - photos (traffic!)

That is correct what João says about the 9x radio voltage to the gimbals being 5 volts.
You should do a mod to change the gimbals's voltage down to 3.3 volts,
because in some amount of time it will burn-out your new M9 gimbals.
by bob195558
Fri Aug 23, 2019 10:05 am
Forum: General Information & Rules
Topic: FAA Unmanned Aircraft Systems Registration 2015 (FAA registrations are reinstated 2018)
Replies: 179
Views: 53084

Re: FAA Unmanned Aircraft Systems Registration 2015 (FAA registrations are reinstated 2018)

Received this email, not sure if it is real or not.
The email address is: "Federal Aviation Administration" <[email protected]>
Click on photo to zoom in.

Federal Aviation Administration.jpg
by bob195558
Fri Aug 23, 2019 9:30 am
Forum: Hardware
Topic: FrSky M9 gimbals in a 9x - photos (traffic!)
Replies: 108
Views: 22149

Re: FrSky M9 gimbals in a 9x - photos (traffic!)

Yes, as you found the 9x radio wiring colors are not to code.
by bob195558
Thu Aug 22, 2019 2:58 pm
Forum: openTx
Topic: Ailerons moving slow & with delay
Replies: 35
Views: 5749

Re: Ailerons moving slow & with delay

I have never looked for Shielded Servo Wires or what we could be use for Shielded Servo Wires. Having Shielded Servo Wires would be helpful when servo wires need to be close to each other. Looks like we would have to make our own Shielded Servo Wires. I think we could maybe just connect the shieldin...
by bob195558
Thu Aug 22, 2019 12:15 am
Forum: openTx
Topic: Ailerons moving slow & with delay
Replies: 35
Views: 5749

Re: Ailerons moving slow & with delay

Battery power/voltages up to what they should be ?
Bad wiring ? That is other servo wires to close to each other ?
by bob195558
Wed Aug 21, 2019 11:53 am
Forum: Other Electronic Projects
Topic: List of where to find STL files for 3D Printing (CR10 3D Printing)
Replies: 0
Views: 200

List of where to find STL files for 3D Printing (CR10 3D Printing)

I have been using Thingiverse mostly for finding 3D items to 3D Print. (https://www.thingiverse.com/) There are other web-places where you can search for STL files. If you know of more web-places where STL files are, feel free to let us know about them. Here are some other web-places to search for S...
by bob195558
Tue Aug 13, 2019 1:39 am
Forum: erskyTx (was ersky9x)
Topic: Problem with Taranis x9d plus and multi module
Replies: 19
Views: 1179

Re: Problem with Taranis x9d plus and multi module

I do not have this module, but maybe you need to use the protocol for this module and maybe the module then changes the potocol to the proper protocol for you ? I am thinking maybe there are two places to set proptcol, one place for the module protocol and another place to set which output protocol ...
by bob195558
Fri Aug 09, 2019 11:59 am
Forum: Other Electronic Projects
Topic: Wiring up replacement Alternator for a Triumph TR250 1968
Replies: 4
Views: 860

Re: Wiring up replacement Alternator for a Triumph TR250 1968

Update: I turned the dash light switch all the way down and push on it too and which had no affect. After disconnecting the battery and reconnecting it, the dash lights seem to be working better now as the dash lights are OFF with the battery connected now. Maybe the dash light switch has debris an...
by bob195558
Thu Aug 08, 2019 4:32 pm
Forum: Other Electronic Projects
Topic: Wiring up replacement Alternator for a Triumph TR250 1968
Replies: 4
Views: 860

Re: Wiring up replacement Alternator for a Triumph TR250 1968

Update: With the Smaller Brown / Yellow wire from ignition light to the alternator top small terminal, the new alternator is now Charging properly . :D Note: I also found some more info about the alternator's top small terminal. This top smaller terminal must have at least two volts from the batter...
by bob195558
Thu Aug 08, 2019 11:32 am
Forum: Other Electronic Projects
Topic: Wiring up replacement Alternator for a Triumph TR250 1968
Replies: 4
Views: 860

Re: Wiring up replacement Alternator for a Triumph TR250 1968

This maybe what the wiring should be. Large Brown / White wire from Battery (+) to alternator center large terminal. Smaller Brown / Yellow wire from ignition light to alternator top small terminal. Small Brown / Green wire to ? (maybe to a dash light and maybe connected with the top small terminal).
by bob195558
Thu Aug 08, 2019 10:39 am
Forum: Other Electronic Projects
Topic: Wiring up replacement Alternator for a Triumph TR250 1968
Replies: 4
Views: 860

Re: Wiring up replacement Alternator for a Triumph TR250 1968

Found some more wiring info that looks more like what this new TR250 alternator may be.
Lucas Alternator Wiring_c.jpg
by bob195558
Wed Aug 07, 2019 10:05 pm
Forum: Other Electronic Projects
Topic: Wiring up replacement Alternator for a Triumph TR250 1968
Replies: 4
Views: 860

Wiring up replacement Alternator for a Triumph TR250 1968

Riding in TR250 Car_c.jpg Hi, I am having trouble with getting the charging system to work. I have a 1968 Triumph TR250 which I got it back in 1973 that needed a lot of repairs. The alternator (charging system) was not working and I had an old Chrysler generator which I installed (this was working ...
by bob195558
Mon Aug 05, 2019 7:22 pm
Forum: openTx
Topic: How do I read single cell voltages in Telemetry screen?
Replies: 10
Views: 592

Re: How do I read single cell voltages in Telemetry screen?

Thank you João, I must have missed that info.
Maybe he should use FrSky, so then would not have a problem any more ?
by bob195558
Mon Aug 05, 2019 10:32 am
Forum: openTx
Topic: How do I read single cell voltages in Telemetry screen?
Replies: 10
Views: 592

Re: How do I read single cell voltages in Telemetry screen?

Maybe you need this sensor: (https://www.frsky-rc.com/product/flvss/), (https://alofthobbies.com/frsky-sp-flvs-smart-port-lipo-voltage-sensor.html). So you are new to the RC Hobby and we understand the difficulty and frustration you may be having. Be penitent, you have some of the best people in the...
by bob195558
Tue Jul 23, 2019 2:56 pm
Forum: Other Electronic Projects
Topic: 3D Printing with PETG Filament (CR10 3D Printing)
Replies: 13
Views: 1172

Re: 3D Printing with PETG Filament (CR10 3D Printing)

Sorry for the late update, been busy with other things. The lower temperatures have helped printing the PETG filament to bond together much better. Hotend temp was 250c and lowered it to 240c. Print-bed was 210c and lowered it to 80c. Rim 2 fb3 PETG_f.jpg Rim 2 fb3 PETG_g.jpg The bad results, still ...
by bob195558
Tue Jul 23, 2019 11:52 am
Forum: er9x
Topic: er9x development
Replies: 3117
Views: 382743

Re: er9x development

Also the templates can still be used in eepe's (computer) ?
So maybe there could be more stuff remove that would then be available only in eepe for setup purposes ?
by bob195558
Sat Jul 20, 2019 12:53 am
Forum: Other Electronic Projects
Topic: 3D Printing with PETG Filament (CR10 3D Printing)
Replies: 13
Views: 1172

Re: 3D Printing with PETG Filament (CR10 3D Printing)

Progress Update:


Rim 2 fb3 PETG_c.jpg
Rim 2 fb3 PETG wheel

Rim 2 fb3 PETG_pi_d.jpg
EZPi (Octopi) Raspberry Pi 3B
by bob195558
Fri Jul 19, 2019 11:23 pm
Forum: Other Electronic Projects
Topic: 3D Printing with PETG Filament (CR10 3D Printing)
Replies: 13
Views: 1172

Re: 3D Printing with PETG Filament (CR10 3D Printing)

Update: 80°C for the Heat Print-Bed seems to be working well for me.
Though there may be still some strings and not able to see yet how well or badly the PETG is bonding together.
by bob195558
Fri Jul 19, 2019 10:25 pm
Forum: Other Electronic Projects
Topic: 3D Printing with PETG Filament (CR10 3D Printing)
Replies: 13
Views: 1172

Re: 3D Printing with PETG Filament (TH3D EZMat and EZFlex Sheet) (CR10 3D Printing)

Thank you Kilrah, I some how had missed seeing this. ----------------------------------------------------------------------------------------------------------- Using TH3D EZMat when printing PETG filament, set temp to: 70°C · PETG has a tendency to bond to the EZMat surfaces to much (all brands can...
by bob195558
Fri Jul 19, 2019 6:21 pm
Forum: Other Electronic Projects
Topic: 3D Printing with PETG Filament (CR10 3D Printing)
Replies: 13
Views: 1172

Re: 3D Printing with PETG Filament (CR10 3D Printing)

PETG heat bed at 80c.jpg First Layer is printing better with Heated Print-Bed at 80°C. The Hotend temperature is at 240°C Need to let it print (give it a chance) to see how these temperatures perform with this NovaMaker PETG filament. PETG heat bed set to 80c_.jpg Note: Having the Heated Print-Bed ...

Go to advanced search