Search found 1918 matches

by bob195558
Sun Oct 14, 2018 10:26 pm
Forum: er9x
Topic: ER9x and multiprotocol problems
Replies: 27
Views: 2298

Re: ER9x and multiprotocol problems

Hi HTeixeira, ER9x is a different 9x radio firmware, if we understand you correctly, you have an unmodified 9x radio (original 9x radio). This string is about 9x radios that have there firmware upgraded to ER9x (http://www.er9x.com/) and then you would have purchased a Multiprotocol Module that you ...
by bob195558
Fri Oct 12, 2018 3:45 am
Forum: Other Electronic Projects
Topic: Adhesion to Heated Print Bed (3D Printing)
Replies: 9
Views: 2572

Nozzle to close to Print-bed surface, Adhesion to Heated Print Bed (3D Printing)

When you have your Nozzle to close to your Print-bed surface: If your Z-Offset (Nozzle) is to close to the print bed, it can not make the EZABL compensation. Raise the Nozzle that is to close to the print-bed side UP , so that the Z-Offset (EZABL) can do its job of adjusting the Z-axis down on the ...
by bob195558
Fri Oct 12, 2018 3:39 am
Forum: Other Electronic Projects
Topic: Dual Z Screw Drives using a Single Z Stepper Motor (CR10 3D Printer)
Replies: 5
Views: 1177

Nozzle to close to Print-bed surface, Dual Z Screw Drives using a Single Z Stepper Motor (CR10 3D Printer)

When you have your Nozzle to close to your Print-bed surface: If your Z-Offset (Nozzle) is to close to the print bed, it can not make the EZABL compensation. Raise the Nozzle that is to close to the print-bed side UP , so that the Z-Offset (EZABL) can do its job of adjusting the Z-axis down on the ...
by bob195558
Fri Oct 12, 2018 3:34 am
Forum: Other Electronic Projects
Topic: CR10 3D-Printer, EZABL Bed Leveling / Tramming Upgrade Mod
Replies: 32
Views: 7191

Nozzle to close to Print-bed surface, CR10 3D-Printer, EZABL Bed Leveling / Tramming Upgrade Mod

When you have your Nozzle to close to your Print-bed surface: If your Z-Offset (Nozzle) is to close to the print bed, it can not make the EZABL compensation. Raise the Nozzle that is to close to the print-bed side UP , so that the Z-Offset (EZABL) can do its job of adjusting the Z-axis down on the ...
by bob195558
Tue Oct 09, 2018 12:27 am
Forum: Turnigy 9XR PRO radio
Topic: 9XR PRO - better gimbals
Replies: 89
Views: 16015

Re: 9XR PRO - better gimbals

Hi João,
Thank you for the info, I see where it could now !
Pot Short_c.jpg
Pot Short_c.jpg (31.05 KiB) Viewed 62 times
by bob195558
Mon Oct 08, 2018 9:57 pm
Forum: Turnigy 9XR PRO radio
Topic: 9XR PRO - better gimbals
Replies: 89
Views: 16015

Re: 9XR PRO - better gimbals

If you connect the 3.3V wire to the center of the pot and ground at one end, you might destroy the pot and probably the voltage regulator. João Hi João, (might destroy the pot) Is this just for the 9XR-Pro and/or dose this also include the 9X radios too ? :?: (with all there upgrade boards too) See...
by bob195558
Mon Oct 08, 2018 7:56 pm
Forum: Turnigy 9XR PRO radio
Topic: 9XR PRO - better gimbals
Replies: 89
Views: 16015

Re: 9XR PRO - better gimbals

I am not sure with the 9XR-Pro wire colors. João would know if the 9XR-Pro wire colors are normal World Standard Wire Colors. I say this because the 9x-radio wire colors are not standard as with them you would have to check each wire to identify what it is. They never specked World Standard Wire Col...
by bob195558
Wed Oct 03, 2018 5:56 pm
Forum: Turnigy 9XR PRO radio
Topic: Frsky current sensor FCS-150A and 9XRpro with XJT module
Replies: 35
Views: 2273

Re: Frsky current sensor FCS-150A and 9XRpro with XJT module

What version of erSky9x do you have on your 9XR-pro ?
You may have an old firmware version.
by bob195558
Wed Oct 03, 2018 2:32 pm
Forum: Other Electronic Projects
Topic: CR10 3D-Printer, EZABL Bed Leveling / Tramming Upgrade Mod
Replies: 32
Views: 7191

EZABL – Storing Bed Leveling Mesh & Updating Your Slicer, EZABL Bed Leveling / Tramming

EZABL – Storing Bed Leveling Mesh (data) & Updating Your Slicer If you are printing a lot and would like to save some time between print jobs, you may want to store your printer's bed-leveling-data so that the EZABL print-bed-surface mapping process will skip this function and use the last stored b...
by bob195558
Fri Sep 28, 2018 7:02 pm
Forum: Other Electronic Projects
Topic: Dual Z Screw Drives using a Single Z Stepper Motor (CR10 3D Printer)
Replies: 5
Views: 1177

Re: Dual Z Screw Drives using a Single Z Stepper Motor (CR10 3D Printer)

Have been printing with this Dual Z Screw Drive upgrade
and it is notable that there is a lot more stability with the printing process.


Death Trooper Helmet Part 12_.jpg

Part8 at 41.5hrs_100percent Finish_Bk.jpg
by bob195558
Fri Sep 07, 2018 10:51 pm
Forum: er9x
Topic: er9x development
Replies: 3094
Views: 291921

Re: er9x development

If Mike is not able to and you do not have the 128 chip, here is where there is an option to upgrade your board with the ATMEGA2561-16AU CPU Chip: (https://openrcforums.com/forum/viewtopic.php?f=95&t=3819&p=74105#p74105). This was a long time ago, but Mike and João will help you through the process....
by bob195558
Mon Sep 03, 2018 11:39 am
Forum: openTx
Topic: Bind dual FS-IA6B
Replies: 10
Views: 486

Re: Bind dual FS-IA6B

3djc wrote:
Mon Sep 03, 2018 7:00 am
You do not need two modules to have 16 chans on X series.
Just bind one receiver on 1-8 and another one on 9-16
(just make sure one of the receiver only is bound with telemetry)
3djc
That is correct !

ErSky9x allows you to have more options to choose from.
by bob195558
Mon Sep 03, 2018 11:31 am
Forum: openTx
Topic: Taranis X9D migrating 2.0 to 2.1/2.2 impact?
Replies: 13
Views: 430

Re: Taranis X9D migrating 2.0 to 2.1/2.2 impact?

bit off topic Hi kalle123, I am not using Linux, I use Win 7 64bit, maybe Mike can answer your question. bit on topic Thank you João, you answered better then I did. That ErSky9x has no troubles when updating to the newest versions. Just wanted to note that there is an option to use ErSky9x firmware...
by bob195558
Mon Sep 03, 2018 2:19 am
Forum: openTx
Topic: Taranis X9D migrating 2.0 to 2.1/2.2 impact?
Replies: 13
Views: 430

Re: Taranis X9D migrating 2.0 to 2.1/2.2 impact?

I believe you may have less troubles if you were to try "erSky9x for Taranis": (http://www.er9x.com/).
I use erSky9x firmware on my Taranis and eepSkye on my PC.
by bob195558
Fri Aug 31, 2018 5:08 pm
Forum: openTx
Topic: Bind dual FS-IA6B
Replies: 10
Views: 486

Re: Bind dual FS-IA6B

Hi, you can also purchase some "Y harness 6 inch/Reverser Heavy-Duty" (ERXA325). Horizon hobby (EXPERT Electronics) is where I got them several years ago. This allows you to use one receiver channel for two servos as it reverses one of the servos. Here is some old info that may be helpful : (http://...
by bob195558
Sun Aug 26, 2018 10:21 pm
Forum: FrSky Taranis radio
Topic: SP-FLVS causing radio interference?
Replies: 14
Views: 714

Re: SP-FLVS causing radio interference?

I can not remember, but does the Taranis also have a Watch Battery in it (to keep date and time), like the 9XTreme board does ?
by bob195558
Sat Aug 25, 2018 8:39 pm
Forum: Other Electronic Projects
Topic: Dual Z Screw Drives using a Single Z Stepper Motor (CR10 3D Printer)
Replies: 5
Views: 1177

Re: Dual Z Screw Drives using a Single Z Stepper Motor (CR10 3D Printer)

I now have this Dual Z Screw Drives using the Single Z Stepper Motor Mod COMPLETED ! :D Some Installing Notes: 1) Will need to fit and deburr any ragged or raised edges on the outside of the Threaded Lead Screws and the inside of the Bearing. The Bearing Pillow Block have two setscrews that have la...
by bob195558
Sat Aug 25, 2018 3:37 pm
Forum: FrSky Taranis radio
Topic: SP-FLVS causing radio interference?
Replies: 14
Views: 714

Re: SP-FLVS causing radio interference?

Are you using a 5A BEC ?
by bob195558
Fri Aug 24, 2018 1:46 pm
Forum: General Information & Rules
Topic: [Solved] Problem with forum. Repeatedly "signed off"
Replies: 52
Views: 2556

Re: Problem with forum. Repeatedly "signed off"

I have been using " Active topics " which has the newest " Unread posts " in them. Is "Active topics" then affected also ? :?: Short time ago, I was at Munich and for a week and I never was logged off when I was reading the unread posts. Reinhard Seems maybe some people are only affected for where t...
by bob195558
Fri Aug 24, 2018 10:48 am
Forum: General Information & Rules
Topic: [Solved] Problem with forum. Repeatedly "signed off"
Replies: 52
Views: 2556

Re: Problem with forum. Repeatedly "signed off"

ReSt wrote:
Fri Aug 24, 2018 10:12 am
I get logged off for nearly every post that I want to read.
If there are 5 unread postings, I probably have to sign in 4 or 5 times to read them.
Reinhard
Hi Reinhard,
But you do not have to be signed in to read them, ....... right ?
by bob195558
Thu Aug 23, 2018 11:06 pm
Forum: General Information & Rules
Topic: [Solved] Problem with forum. Repeatedly "signed off"
Replies: 52
Views: 2556

Re: Problem with forum. Repeatedly "signed off"

How many members is this affecting ?
I try to write the message first with WORD then copy and past
and most of the time it auto signs in with no troubles when I open.
by bob195558
Thu Aug 23, 2018 10:57 pm
Forum: General Information & Rules
Topic: [Solved] Problem with forum. Repeatedly "signed off"
Replies: 52
Views: 2556

Re: Problem with forum. Repeatedly "signed off"

I use Google Chrome Version 68.0.3440.106 (Official Build) (64-bit)
and Firefox Quantum 61.0.2 (32bit)
and I have not had this problem of being signed out randomly.

I hope it is fixed soon for you guys !
by bob195558
Tue Aug 21, 2018 1:16 am
Forum: Other Electronic Projects
Topic: Dual Z Screw Drives using a Single Z Stepper Motor (CR10 3D Printer)
Replies: 5
Views: 1177

Re: (CR10 3D Printer) Single Z Stepper Motor with Dual Lead Screws Upgrade

UPDATE: Making a little progress
dual Z drive_a.jpg
Dual Z Drive
I have some parts still on order.
by bob195558
Mon Aug 20, 2018 3:40 pm
Forum: Turnigy 9XR PRO radio
Topic: 9XR PRO - better gimbals
Replies: 89
Views: 16015

Re: 9XR PRO - better gimbals

I believe they are.
I upgraded my Taranis-x9d (using erSky9x firmware) and it made a real difference.
Feels like I have better control over the standard Taranis Gimbals when flying.

Bob B.
by bob195558
Sun Aug 19, 2018 1:17 am
Forum: Turnigy 9XR PRO radio
Topic: Wierd issue with right gimbal
Replies: 82
Views: 8215

Re: Wierd issue with right gimbal

Now you see how poor quality these pots are.
Just by pushing it around can brake or fix them.
by bob195558
Sun Aug 19, 2018 1:06 am
Forum: Other Electronic Projects
Topic: CR10 3D-Printer, EZABL Bed Leveling / Tramming Upgrade Mod
Replies: 32
Views: 7191

Baby-Step feature, CR10 3D-Printer, EZABL Bed Leveling / Tramming Upgrade Mod

Some info about the TH3D Baby-Step feature. TH3D Baby-Step feature works two ways. First Way: Baby-Step only adjust with the job you are running and does NOT auto sent the Baby-Step adjustment value to the Z-Offset. You have to compute the Baby-Step value to the Z-Offset value and then "Store setti...
by bob195558
Sun Aug 19, 2018 1:03 am
Forum: Other Electronic Projects
Topic: Updating CR10 3D Printer with TH3D_UFW_U1.R2.T4_Testing Firmware
Replies: 1
Views: 552

TH3D Baby-Step feature works two ways (Updating CR10 3D Printer with TH3D_UFW_U1.R2.T4_Testing Firmware)

Some info about the TH3D Baby-Step feature. TH3D Baby-Step feature works two ways. First Way: Baby-Step only adjust with the job you are running and does NOT auto sent the Baby-Step adjustment value to the Z-Offset. You have to compute the Baby-Step value to the Z-Offset value and then "Store setti...
by bob195558
Fri Aug 17, 2018 12:54 pm
Forum: Turnigy 9XR PRO radio
Topic: Questions about RSSI
Replies: 7
Views: 560

Re: Questions about RSSI

Here is some info :) if you want to dig into this some more: How do Antennas work ? :[/u] (https://www.youtube.com/watch?v=fSoXIqBlg9M&t=610s). Antenna theory: The FrSky receiver antenna puzzle (part 1): (https://www.youtube.com/watch?v=WBE_KqqHbM0&t=183s), (https://www.youtube.com/watch?v=xCVd3QGQh...
by bob195558
Sun Aug 12, 2018 1:10 am
Forum: Other Electronic Projects
Topic: Updating CR10 3D Printer with TH3D_UFW_U1.R2.T4_Testing Firmware
Replies: 1
Views: 552

Updating CR10 3D Printer with TH3D_UFW_U1.R2.T4_Testing Firmware

Flashing TH3D_UFW_U1.R2.T4_Testing Firmware Note: Testing Firmware may contain bugs, so when trying any new testing firmware be aware that there may still be some bugs. Report all bugs to the #beta-testing channel on TH3D Discord server: (https://discordapp.com/channels/457081983294504961/472083221...

Go to advanced search