openrcforums

and if you used ersky9x you could add some more switches, and i think at least one slider.. Not sure about this one :) João ;-) that is true.. when i took it apart, i noticed the two connectors... i looked them up and saw a post by Mike on making them 2POS Switches or Sliders, etc... I purposely we...

yeah, the prices the Ar9x and ArUni sold are unbeatable :( I which they were back on the market.. And I would rather buy one of those than the X7. I have two and they are great.. Shame really :( João I just bough the QX7S I am really enjoying it... the only mod i had to do was add a power charging ...

Hey Joao, yes... absolutely... its a funny thing as I was just researching that, no foolin... ;-) Considering I only use FrSky for the most part but as long as I can get Telemetry and connect to my X and D Series Rx's and my VD5M. Frsky (Based on CC2500 Chip) should do the trick with an Adruino Pro ...

Hello All, not that this is any milestone or triumph compared to some of the brain power in this forum... just wanted to share a build that I just completed with some spare parts seeing that I didn't have a 9x Radio anymore and was my introduction into this forum many years ago. Thanks to some docum...

Man its been a while since my last post. I am still tinkering, literally... I have sold all my radios but I still manage to have 2 quads left of my 8. That being said at one point I had 4-5 9x radios. With all the mods I have enough spare parts to build one... So i did. Now, I was trying to figure o...

It works very well :) I have basically an arduino voice module in one of my radios, and it connects to the 9x mainboard via just 2 wires instead of all 4 to the LCD vias, as well as the one on PB7. This gave me 2 more switches (push buttons in my case) and also freed some other connections for othe...

Problem solved... The cuprit was a faulty cable that connects the TeZ to the Switches. Apparently the AIL Lead was faulty... or loosen from the Crimped Connector. Luckily, I have purchased a Crimpt Set and connectors for another project that I was working on with my Laser Cutter. That being said, a...

That option is to be used when you connect the Megasound board via Serial. If yours is connected to the LCD vias, leave it off, or of course, it will break audio, backlight, and throttle trims.. :) João Sent from my BLN-L21 using Tapatalk Lol. Been away too long. That feature works great then. 😜

MikeB wrote: ↑Sat Jan 13, 2018 6:45 pm I made a mistake and r821 does report as r820.

Have you also ticked "FrSky Mod Done"?

Mike.

I have with no affect.
I have also found a bug with r820/1 with the Megasound-Serial option. It breaks the backlight and audio when enabled.

https://github.com/MikeBland/9x-telemetrez/blob/master/src/telemetrEZ.hex Should be the latest anyway. All the source files are there as well. Mike. Hello Mike, thanks for the link... I did find that on your site.. didn't know if it was r90. The file size matches what I had in my drive. That being ...

Does anyone have latest r90 or r89 for TeZ?
Links to firmware are all dowm.

Thanks.

Nevermind, i found them on a system i had...

Alright, where I am at now is that the side load cable for the TeZ is repaired and the GEAR and TRN and ID0/1/2 are working again... I had a lose GND wire in the connector. I am still only able to update to : VERS: V1.748-Mike DATE: 30.11.2016 TIME: 13.41.21 SVN: er9x-r820 MOD: FRSKY 128 and the THR...

To enable the hardware menu, power the radio while holding the left horizontal trim to the left for about a second, and then release it. Hardware menu in Radio Setup/Hardware should be enabled João Thanks that worked great... I forgot about that... but the problem still exists.. i have noticed that...

Strangely enough...
I have downloaded the file for r821 but it seems that this is getting installed instead

VERS: V1.748-Mike
DATE: 30.11.2016
TIME: 13.41.21
SVN: er9x-r820
MOD: FRSKY 128

Correct, my bad.. AIL... I was in a B100 update/install so I didn't see the screen. I am loading er9x-128-r821.hex on there now... I have seen that in the Config Screen in eepe.. not on the radio, I will check.

Tell me about it... the only problem now is that with r820 or r821 I can't seem to get the TeZ to enable... and fix the THR and RUD AIL .
Starting the process over again...

yup, r421 is the latest on er9x.com
and I am running it on a Windows Machine... I have had no success on my Mac.

Hey Joao, long time no msg.... hope all is well... that being said, yes, i did try that several times... Funny thing, i just remembered what I had to do to fix this issue. I had to program the system with OpenTx via Companion 2.1. That was successful. Then program it again with Companion 2.1 and loa...

Well, its been a long time since my last post... I do recall the last time I tried to update this particular radio that i had an issue and swore to never update it again. That being said, I have sold it and was making some changes to the config and accidentally updated the firmware. I can't get Er9x...

oh awesome... great to hear it.
Enjoy!

bob195558 wrote:Hi Kilrah,
Not with this price: (http://www.hobbyking.com/hobbyking/stor ... dule_.html).
(Sale price: $59.99).

Man that is cheap... but its so ugly..
I guess they are clearing the way for new stuff...

Sold to Octavios...

Sorry, didn't see the posts...
its just the 9Xtreme.. brand new in the box...
comes with :

C$32.12 reg price
C$16 1/2 price

9X Main Board M64 (Brand New in the box)

$12

9x-m128 / Telemetry Mod / FrSky Lite Converter / MegaSound9x(Serial) / er9x

Make me an offer....

9x-m128 / TeZ / SP Rev 2.4 / Rotary Encoder / Haptic / MegaSound9x(Serial) / er9x

Make me an offer...

C$92.36 Regular Cost
C$46.18 1/2 price

Wow, you guys have been busy.... great stuff on the Mavlink Support Mike et al. I will have to read on to see if any updates to the 9XTreme Mavlink Support... (not the (9XPro). Last I recall was that we pretty much had all working Telemetry wise with the ArduinoProMini running on the Quad(APM) side....

Yes, r820 includes SBUS protocol. I have no idea about the "unplug the battery" problem! I can only guess it is not armed any more. No one else has reported they are using SBUS, although the MULTI protocol now uses almost the same protocol, so shares the code, and that is working OK. Mike...