Search found 107 matches
- Wed Nov 22, 2017 8:19 am
- Forum: sky9x upgrade board
- Topic: sky9x rev. B1 power issue
- Replies: 67
- Views: 44960
Re: sky9x rev. B1 power issue
Suggestion, you may want to look at your main power switch for the problem. Thank you. I disassemble it and spray it with a similar product, but there is no change. I don't know if it was the same for you, but when it doesn't work, my FrSky module beeps and the red light at the back is on, making m...
- Wed Nov 22, 2017 8:17 am
- Forum: sky9x upgrade board
- Topic: sky9x rev. B1 power issue
- Replies: 67
- Views: 44960
- Mon Nov 20, 2017 9:42 pm
- Forum: sky9x upgrade board
- Topic: sky9x rev. B1 power issue
- Replies: 67
- Views: 44960
Re: sky9x rev. B1 power issue
MY FAULT :o The battery of my voltmeter is deplated and i didn’t realised that. All my voltages measures were wrong, i’m sorry for this stupid mistake :? I confirm that the output of the regulator is a stable 3.3V The replacement of the regulator maybe useless but at least we know it is not faulty a...
- Mon Nov 20, 2017 7:57 pm
- Forum: sky9x upgrade board
- Topic: sky9x rev. B1 power issue
- Replies: 67
- Views: 44960
Re: sky9x rev. B1 power issue
Thanks a lot !
I'll buy 4.7uF capacitors for the test.
And i have a 2S LiFe battery that i will use for the test.
I tried the LiFe battery as is but the regulator output is still a 4.5V
Can you confirm me this is what i need to do :
I'll buy 4.7uF capacitors for the test.
And i have a 2S LiFe battery that i will use for the test.
I tried the LiFe battery as is but the regulator output is still a 4.5V
Can you confirm me this is what i need to do :
- Mon Nov 20, 2017 1:18 pm
- Forum: sky9x upgrade board
- Topic: sky9x rev. B1 power issue
- Replies: 67
- Views: 44960
Re: sky9x rev. B1 power issue
I have received the new 3.3 regulator and replaced it on the board.
Unfortunately, the problem remains.
With this new regulator i read 4.50v on the 3.3 pins.
It maybe a bit more than with the previous one.
The behaviour of the radio startup has not changed
Unfortunately, the problem remains.
With this new regulator i read 4.50v on the 3.3 pins.
It maybe a bit more than with the previous one.
The behaviour of the radio startup has not changed
- Wed Nov 15, 2017 8:51 am
- Forum: sky9x upgrade board
- Topic: sky9x rev. B1 power issue
- Replies: 67
- Views: 44960
Re: sky9x rev. B1 power issue
Does the regulator get quite hot when this happens? I did the test : i leaved the radio in bad "powered up" state for about 3 minutes (module has beeped, screen stays blank, and 3.3 pin are measured at 0.40V), but the heatsink of the regulator stays cold. Once managed to boot up (On/Off c...
- Tue Nov 14, 2017 7:05 pm
- Forum: sky9x upgrade board
- Topic: sky9x rev. B1 power issue
- Replies: 67
- Views: 44960
- Tue Nov 14, 2017 6:48 pm
- Forum: sky9x upgrade board
- Topic: sky9x rev. B1 power issue
- Replies: 67
- Views: 44960
Re: sky9x rev. B1 power issue
210 mA with my FrSky DJT module installed.
You read well that was a solid 4.30V
Before writing this new message i did the test once more : now i read 4.02V (My voltmeter is accurate)
You read well that was a solid 4.30V
Before writing this new message i did the test once more : now i read 4.02V (My voltmeter is accurate)
- Tue Nov 14, 2017 6:04 pm
- Forum: sky9x upgrade board
- Topic: sky9x rev. B1 power issue
- Replies: 67
- Views: 44960
Re: sky9x rev. B1 power issue
@MikeB ersky9x shows 210Ma of current The 3.3 pins are mesured at 0.40V when the switch is ON and the radio doesn't bootup, 4.30V when i have managed to boot it up (by switching it OFF and ON again) @SkyNorth Thanks a lot for your advices. I never manipulated the regulator/heatsink : it still seams ...
- Tue Nov 14, 2017 11:14 am
- Forum: sky9x upgrade board
- Topic: sky9x rev. B1 power issue
- Replies: 67
- Views: 44960
Re: sky9x rev. B1 power issue
With TRN switch maintained : https://www.youtube.com/edit?o=U&video_id=2alwEjZMl5Q Without : https://www.youtube.com/edit?o=U&video_id=3YZPzniD0o8 I discover something : if the radio is plugged many seconds before to the USB without switching it up, then the startup is much faster : 4 second...
- Mon Nov 13, 2017 2:17 pm
- Forum: sky9x upgrade board
- Topic: sky9x rev. B1 power issue
- Replies: 67
- Views: 44960
Re: sky9x rev. B1 power issue
The bootloader is 2.1 When connecting to the PC through USB, the scenario is stable : the radio screen always shows the bootloader with "Connecting" after about 10 secs. (There is no "random" behaviour like there is when the radio is powered by the 2S LiPo) Thanks a lot for your ...
- Sun Nov 12, 2017 12:22 pm
- Forum: sky9x upgrade board
- Topic: sky9x rev. B1 power issue
- Replies: 67
- Views: 44960
Re: sky9x rev. B1 power issue
OK thanks. On the video it starts OK but the issue still occurs, in this situation we don't see the screen flashing, it remains off. After a few flying session, i realise that i lost the audio on the radio after a few minutes (i've tested with different firmwares, differents SD cards) Maybe it's the...
- Sat Nov 11, 2017 9:49 am
- Forum: sky9x upgrade board
- Topic: sky9x rev. B1 power issue
- Replies: 67
- Views: 44960
Re: sky9x rev. B1 power issue
I'm not sure why you get the Bad EEPROM data screen, but other than that, the radio started correctly. This is "normal", i previously flashed it with OpenTX before this test. If you're unsure about the oscillator, maybe i can replace it if it is cheap, i don't take a huge risk i guess ?
- Fri Nov 10, 2017 5:26 pm
- Forum: sky9x upgrade board
- Topic: sky9x rev. B1 power issue
- Replies: 67
- Views: 44960
Re: sky9x rev. B1 power issue
Thanks a lot, here it is :
I will say 5 flash ? (depending if you count the first one when switching on)
https://www.youtube.com/watch?v=eL_B6pNb9PY&feature=share
I will say 5 flash ? (depending if you count the first one when switching on)
https://www.youtube.com/watch?v=eL_B6pNb9PY&feature=share
- Fri Nov 10, 2017 8:41 am
- Forum: sky9x upgrade board
- Topic: sky9x rev. B1 power issue
- Replies: 67
- Views: 44960
Re: sky9x rev. B1 power issue
Thanks a lot. After many tests and considering your remarks here is the situation. I can observe 3 differents situations at startup, they all happens with differents firmwares (old erksy9x, latest ersky9x, boot-test ersky9x, latest OpenTx) 1. The module beeps but the radio never power On, even after...
- Thu Nov 09, 2017 2:49 pm
- Forum: sky9x upgrade board
- Topic: sky9x rev. B1 power issue
- Replies: 67
- Views: 44960
- Thu Nov 09, 2017 1:26 pm
- Forum: sky9x upgrade board
- Topic: sky9x rev. B1 power issue
- Replies: 67
- Views: 44960
Re: sky9x rev. B1 power issue
What happens if you power the radio on, then wait at least 10 seconds, does it then start. No, i can leave the radio like that for minutes, it won't power on, until i switch it off/on again. The 2nd test is OK : i get the "USB" screen, the SD Card is not mounted and the COM port is access...
- Thu Nov 09, 2017 10:53 am
- Forum: sky9x upgrade board
- Topic: sky9x rev. B1 power issue
- Replies: 67
- Views: 44960
Re: sky9x rev. B1 power issue
That black splash screen when you turn the radio on is not normal, right? This strange screen is an OpenTX issue with sky9x board as far as i remember, ersky9x does not have this issue (2nd video) My radio is still useable once i managed to power it up, i hope the problem won't get worst and lead t...
- Thu Nov 09, 2017 5:01 am
- Forum: sky9x upgrade board
- Topic: sky9x rev. B1 power issue
- Replies: 67
- Views: 44960
- Wed Nov 08, 2017 10:08 pm
- Forum: sky9x upgrade board
- Topic: sky9x rev. B1 power issue
- Replies: 67
- Views: 44960
Re: sky9x rev. B1 power issue
Bootloader and co-processor updated (No incidence on the issue)
- Wed Nov 08, 2017 8:26 pm
- Forum: sky9x upgrade board
- Topic: sky9x rev. B1 power issue
- Replies: 67
- Views: 44960
Re: sky9x rev. B1 power issue
Here is the video with ersky9x, the part i slide the power switch for the first time is missing.
By the way it says that i need to update the co-processor, i'm looking forward to dot it.
https://youtu.be/xnf4rSmH60s
By the way it says that i need to update the co-processor, i'm looking forward to dot it.
https://youtu.be/xnf4rSmH60s
- Wed Nov 08, 2017 7:39 pm
- Forum: sky9x upgrade board
- Topic: sky9x rev. B1 power issue
- Replies: 67
- Views: 44960
Re: sky9x rev. B1 power issue
Yes same behaviour: i press the 2 trims inwards then switch on the power, i hear the module beep, but the LCD remains blank. I switch it off (keeping my 2 fingers on the trims) then switch it on, then the bootloader (v1.9) screen shows. What is the normal behaviour when connected to my computer USB ...
- Wed Nov 08, 2017 6:27 pm
- Forum: sky9x upgrade board
- Topic: sky9x rev. B1 power issue
- Replies: 67
- Views: 44960
Re: sky9x rev. B1 power issue
Thanks for the hint bob195558 that could make sense.
i don't think i have a the RTC module on it. Was it an option with the sky9x rev. B1 ?
i don't think i have a the RTC module on it. Was it an option with the sky9x rev. B1 ?
- Wed Nov 08, 2017 6:22 pm
- Forum: sky9x upgrade board
- Topic: sky9x rev. B1 power issue
- Replies: 67
- Views: 44960
Re: sky9x rev. B1 power issue
Hi Joao, thanks for your answer. it's OpenTX 2.2 for sky9x boards. The screen you see is the checklist display page. Previously it was flashed with a late 2012 version of ersky9x, but the problem was already there. 2 years ago, before i make a break in the hobby, i never faced this issue, that's why...
- Wed Nov 08, 2017 5:01 pm
- Forum: sky9x upgrade board
- Topic: sky9x rev. B1 power issue
- Replies: 67
- Views: 44960
sky9x rev. B1 power issue
Hi, i'm taking back my modified T9X radio after 2 years of break and it doesn't power on very well. The 2S LiPo is good (fully charged, 8.4V measured at output), i can hear the beep from the FrSky module, but the radio does not power on. I have to switch it off and on again, then it powers up. See i...
- Sun Dec 22, 2013 7:37 pm
- Forum: erskyTx (was ersky9x)
- Topic: Aurora gimbal usable ?
- Replies: 141
- Views: 92239
Re: Aurora gimbal usable ?
Thanks a lot, here are the results:
So the gain of 2 seems to be the best compromise.
Like you were expecting, some sticks have their min/max values, about a half millimeter before their stop, it's very small, but it's a kind of "dead zone".So the gain of 2 seems to be the best compromise.
- Sun Dec 22, 2013 6:47 pm
- Forum: erskyTx (was ersky9x)
- Topic: Aurora gimbal usable ?
- Replies: 141
- Views: 92239
Re: Aurora gimbal usable ?
Thanks for the explanation.
If someone is able to calculate the ADC_CGR/ADC_COR values for a gain of 4 (i'm not ) i will tell what are the resulting ranges for the sticks so we know.
But like you said, i agree that it won't make any noticeable difference for the pilot.
If someone is able to calculate the ADC_CGR/ADC_COR values for a gain of 4 (i'm not ) i will tell what are the resulting ranges for the sticks so we know.
But like you said, i agree that it won't make any noticeable difference for the pilot.
- Sun Dec 22, 2013 2:48 pm
- Forum: erskyTx (was ersky9x)
- Topic: Aurora gimbal usable ?
- Replies: 141
- Views: 92239
Re: Aurora gimbal usable ?
Hi, i've just replaced my radio gimbals with the Aurora sticks, i've raised the gains to 2, it seems to work great. I've noticed that the values of the sticks starts from 0x200 and ends at 0x600, meaning that i have a resolution of 1024 steps. With the stock gimbals my values range was 0x0 to 0x800,...
- Fri Dec 20, 2013 6:10 pm
- Forum: openTx
- Topic: Stick gain not working on Sky9x with Aurora sticks
- Replies: 6
- Views: 5341
Re: Stick gain not working on Sky9x with Aurora sticks
Hi, i've found a way for the gimbals gain to work on OpenTx but i have no idea of the risks of using that. The modification is on the comment of the transfered issue on github: https://github.com/opentx/opentx/issues/155 If anyone can help on explaining those ADC mode register settings i would be gl...
- Tue Feb 26, 2013 3:41 pm
- Forum: erskyTx (was ersky9x)
- Topic: Ersky9x + UHF module interferences
- Replies: 15
- Views: 11028
Re: Ersky9x + UHF module interferences
Very interresting, thanks for the tip !