Search found 10 matches

by SkyWalter
Thu Mar 26, 2020 2:34 pm
Forum: Software
Topic: Problems upgrading Turnigy 9X to ER9X
Replies: 17
Views: 2960

Re: Problems upgrading Turnigy 9X to ER9X

I was successful in setting up Homelock, Courselock and Off (IOC) using my additional 3-way switch on Turnigy ER9X. The "CURVE" feature made it real easy. MikeB ... Thank you all your replies to help me and I appreciated your input. You appear to be the expert on ER9X. Thanks to Kilrah and all for t...
by SkyWalter
Thu Mar 26, 2020 12:17 am
Forum: Software
Topic: Problems upgrading Turnigy 9X to ER9X
Replies: 17
Views: 2960

Re: Problems upgrading Turnigy 9X to ER9X

Below I pasted the instructions from the Controller (NAZA-M V2) Software Assistant: ------------------------------------ Intelligent Orientation Control "IOC Setting Procedure Please choose a 3-positions switch on your transmitter as IOC switch, which is also used for recording the multi-rotor orien...
by SkyWalter
Wed Mar 25, 2020 8:36 pm
Forum: Software
Topic: Problems upgrading Turnigy 9X to ER9X
Replies: 17
Views: 2960

Re: Problems upgrading Turnigy 9X to ER9X

What you are suggesting with the curve makes sense to me. I think that should work. Then I will not have to insert additional mixers into CH7. I have not worked on curves. Now I have some reading to do. I do not understand your question about what CH7 should send to these 3 settings. As you can see ...
by SkyWalter
Wed Mar 25, 2020 2:34 pm
Forum: Software
Topic: Problems upgrading Turnigy 9X to ER9X
Replies: 17
Views: 2960

Re: Problems upgrading Turnigy 9X to ER9X

Thanks for the reply Mike. No problem setting the source to P1 or assigning different weights. But if the Source remains as P1, where do I assign the inputs (-100, 0 100)? I am using CH7. Do I insert two more mixes on CH7 to identify each position of the switch and set to "Replace"? Perhaps not. I a...
by SkyWalter
Wed Mar 25, 2020 4:49 am
Forum: Software
Topic: Problems upgrading Turnigy 9X to ER9X
Replies: 17
Views: 2960

Re: Problems upgrading Turnigy 9X to ER9X

I installed an additional 3-way switch on my Turnigy 9x (Now er9x) and swapped the wiring from the P1 to my 3-way switch. I added two resistors per instructions. It appears to be working OK except I have to set up the mixers. The original 3-way switch at Aux 3 has ID0, ID1, ID2 which makes it easy t...
by SkyWalter
Tue Mar 17, 2020 7:46 pm
Forum: Software
Topic: Problems upgrading Turnigy 9X to ER9X
Replies: 17
Views: 2960

Re: Problems upgrading Turnigy 9X to ER9X

All completed. Thank you everyone for your help.
by SkyWalter
Fri Mar 13, 2020 4:10 pm
Forum: Software
Topic: Problems upgrading Turnigy 9X to ER9X
Replies: 17
Views: 2960

Re: Problems upgrading Turnigy 9X to ER9X

Hi, I already programmed Ch 1,2,3,4 for A,E,T,R to match the NAZA-M Controller. That works great! Now I am having problems configuring the 3-way switch. I wish to to make CH 6 ID0, ID1 and ID2 to match GPS, ATTI and MAN in that order. MIXER: (Source ? ) (Weight 100) (Offset 0 ) (Fix Offset ?) (Use O...
by SkyWalter
Thu Mar 12, 2020 2:18 pm
Forum: Software
Topic: Problems upgrading Turnigy 9X to ER9X
Replies: 17
Views: 2960

Re: Problems upgrading Turnigy 9X to ER9X

I am currently reading the ER9X Manual which is a good start. I really would like to find a basic model for the Turnigy ER9X to use with the NAZA-M V2 controller. Not seeing much on the Internet. Help from anyone on this would be greatly appreciated.
by SkyWalter
Wed Mar 11, 2020 4:35 am
Forum: Software
Topic: Problems upgrading Turnigy 9X to ER9X
Replies: 17
Views: 2960

Re: Problems upgrading Turnigy 9X to ER9X

Joao, WOW! Thank you very much for that info. Eepe made it easy for me. I now have ER9X Pilot installed on my Turnigy 9X. Now on to the next challenge of setting up the transmitter to control my NAZA-M V2. Everything is new to me of course with ER9X. Perhaps there is a model I could use to get me st...
by SkyWalter
Tue Mar 10, 2020 4:53 pm
Forum: Software
Topic: Problems upgrading Turnigy 9X to ER9X
Replies: 17
Views: 2960

Problems upgrading Turnigy 9X to ER9X

I am just starting to upgrade Turnigy 9X to ER9X and running into problems. I have the hardware mods completed and the USBasp driver looks OK. When I use Companion 2.3 to write the ER9X hex file to the transmitter, it shows that sam-ba.exe not found. Also, I have a solid red light on my usbasp progr...

Go to advanced search