Search found 15 matches

by Shorty54
Sun Apr 07, 2019 6:15 pm
Forum: eePe
Topic: Trouble flashing er9x with eePe
Replies: 37
Views: 9297

Re: Trouble flashing er9x with eePe

I can not find "Multi" in my radio screen after protocol??

Do I find this in the 9x or do I need to use eePe to set it ups?

No rotary knob on my iRange.

Shad
by Shorty54
Sun Apr 07, 2019 12:50 am
Forum: eePe
Topic: Trouble flashing er9x with eePe
Replies: 37
Views: 9297

Re: Trouble flashing er9x with eePe

For starters, I have
Turnigy iA8
Turnigy FSA8s
Hobby King HK-TR6A V2
Orange RX
Spectrum DSMX
Spectrum DSM2
Also a couple off brand ones but not sure if they will work:
Heng Long
Taigen

Shad
by Shorty54
Sun Apr 07, 2019 12:28 am
Forum: eePe
Topic: Trouble flashing er9x with eePe
Replies: 37
Views: 9297

Re: Trouble flashing er9x with eePe

All switches and buttons work. I installed a new 9x main board and it flashed the first time no issues. I now have both my new Turnigy 9x radios flashed with er9x and better back lights. Next step, I purchased the iRangeX IRX4 4 in 1 TX Module. How do I program and what setting are needed to make th...
by Shorty54
Thu Apr 04, 2019 3:58 pm
Forum: eePe
Topic: Trouble flashing er9x with eePe
Replies: 37
Views: 9297

Re: Trouble flashing er9x with eePe

No luck after removing the yellow capacitor, same error..

Thanks,
Shad
by Shorty54
Thu Apr 04, 2019 3:35 pm
Forum: eePe
Topic: Trouble flashing er9x with eePe
Replies: 37
Views: 9297

Re: Trouble flashing er9x with eePe

We have suggested removing the large, yellow capacitor that is just under the crystal. This is on the reset line and can cause the reset signal to be slow activating from the programmer. If it takes too long to apply reset, the processor doesn't see the command to enter programming mode. Try either...
by Shorty54
Thu Apr 04, 2019 2:35 pm
Forum: eePe
Topic: Trouble flashing er9x with eePe
Replies: 37
Views: 9297

Re: Trouble flashing er9x with eePe

MikeB wrote:
Thu Apr 04, 2019 1:55 pm
Please confirm you use an UPPERCASE B, and did you try -B10000.

Mike
-B100, -B1000, -B10000, same error..

Thanks,
Shad
by Shorty54
Thu Apr 04, 2019 12:30 pm
Forum: eePe
Topic: Trouble flashing er9x with eePe
Replies: 37
Views: 9297

Re: Trouble flashing er9x with eePe

MikeB wrote:
Wed Apr 03, 2019 9:06 pm
Yes, in one position they pull the signal to ground through a 200 ohm resistor.

Mike
I tried all combinations of Ail and Thr switches, no luck.

Thanks,
Shad
by Shorty54
Wed Apr 03, 2019 8:53 pm
Forum: eePe
Topic: Trouble flashing er9x with eePe
Replies: 37
Views: 9297

Re: Trouble flashing er9x with eePe

Two of the programming signals use the same pins as the THR and AIL switches. You could try moving these to the opposite position to where they are currently as in the "wrong" position they could cause a programming failure. As João mentioned earlier, also try removing the yellow capacitor just bel...
by Shorty54
Wed Apr 03, 2019 12:45 pm
Forum: eePe
Topic: Trouble flashing er9x with eePe
Replies: 37
Views: 9297

Re: Trouble flashing er9x with eePe

I will tray a new main board. Hopefully that solves the issue.

Thanks,
Shad
by Shorty54
Tue Apr 02, 2019 9:11 pm
Forum: eePe
Topic: Trouble flashing er9x with eePe
Replies: 37
Views: 9297

Re: Trouble flashing er9x with eePe

And you didn't answer one of my questions, or perhaps I've missed it :) Does the radio work when you power it on without programmer? João Radio seems to work fine with and without SP Board installed (about 8 posts up in this thread) I checked the ohms in the places you specified. Both my radios rea...
by Shorty54
Tue Apr 02, 2019 5:11 pm
Forum: eePe
Topic: Trouble flashing er9x with eePe
Replies: 37
Views: 9297

Re: Trouble flashing er9x with eePe

Yes I have switch turned on. I disconnected backlight, same error. I took my other new radio out of the box and installed the same SP board from the one I am trying to flash and it flashed no problem. So is the 9x board faulty? I was told Bangood has Atmega128 9x boards, should I order that on or re...
by Shorty54
Tue Apr 02, 2019 1:41 pm
Forum: eePe
Topic: Trouble flashing er9x with eePe
Replies: 37
Views: 9297

Re: Trouble flashing er9x with eePe

The radios were sealed in a box. I opened them up, removed the battery tray, cheked the battery pos/neg wires on a new Life 3s 9.9v battery, and installed. I turned on the radio and it came on. I pressed the menus keys and moved the sticks around. It seemed to work. I then installed the HK back ligh...
by Shorty54
Tue Apr 02, 2019 1:11 pm
Forum: eePe
Topic: Trouble flashing er9x with eePe
Replies: 37
Views: 9297

Re: Trouble flashing er9x with eePe

Is this what you were looking for?
I did notice a diode in the lower left of the picture.
Its "L100" Its the only one that looks like its soldered crooked???

Shad
T9x Board.jpg
T9x
by Shorty54
Tue Apr 02, 2019 12:44 am
Forum: eePe
Topic: Trouble flashing er9x with eePe
Replies: 37
Views: 9297

Re: Trouble flashing er9x with eePe

I tried -B100 and -B1000, same error code..

Thanks,
shad
by Shorty54
Mon Apr 01, 2019 1:55 pm
Forum: eePe
Topic: Trouble flashing er9x with eePe
Replies: 37
Views: 9297

Trouble flashing er9x with eePe

Hi, I am new here and to the 9x. I have a new Turnigy 9X (never used) with the ATM64. I installed the back light from HK and the Smartie Basic board. I have downloaded the USB drivers from the Smartie site. I downloaded the er9x and eePe from the er9x site. when I try and burn the er9x hex the radio...

Go to advanced search