Search found 34 matches

by heliperry
Tue Feb 25, 2020 10:32 pm
Forum: The FRSKY Forum
Topic: Frsky service center in California
Replies: 0
Views: 2223

Frsky service center in California

Has any one ever tried to get a hold of the Frsky service center in California? I've left 2 messages with no luck.
by heliperry
Fri Feb 21, 2020 4:38 pm
Forum: The FRSKY Forum
Topic: Horus X12s manual
Replies: 0
Views: 1842

Horus X12s manual

Can anyone tell me if Frsky came out with a programming manual for the X12s open tx. I have the X10/X10S user manual open TX 2.2. still trying to figure out my X12S.
by heliperry
Sat Feb 15, 2020 9:12 pm
Forum: The FRSKY Forum
Topic: Differential in elevator set-up
Replies: 18
Views: 2032

Re: Differential in elevator set-up

Mike,
I redid what you suggested and figured it out. I have it working the way I think it should. Everything tracks together also. I have my final rates also. Know I just need to work on my ailerons and rudder next.πŸ€—
I'm sure I'll have more questions.
Thanks again. Heliperry
by heliperry
Sat Feb 15, 2020 6:28 pm
Forum: The FRSKY Forum
Topic: Differential in elevator set-up
Replies: 18
Views: 2032

Re: Differential in elevator set-up

MikeB
I tried what you suggested and it worked on the right elevator that I wasn't able to get my Differential to work originally. But It wouldn't work on the left side so I left it the way it was.
by heliperry
Sat Feb 15, 2020 4:15 pm
Forum: The FRSKY Forum
Topic: Differential in elevator set-up
Replies: 18
Views: 2032

Re: Differential in elevator set-up

Pmullen503, You were right about a machanical issue. I had on of my elevator control rods longer than the other. I fixed that issue.πŸ‘ Reset elevator servo's center's. Started over on my throes and was able to get on low rate on my left elevator +12 degrees and -16 degrees on down elevator with use o...
by heliperry
Sat Feb 15, 2020 1:17 am
Forum: The FRSKY Forum
Topic: Differential in elevator set-up
Replies: 18
Views: 2032

Re: Differential in elevator set-up

Pmullen503
I have checked the machanical setup on the elevators and everything seems to be correct. I am going to check everything out again to double check things.
by heliperry
Fri Feb 14, 2020 5:47 pm
Forum: The FRSKY Forum
Topic: Differential in elevator set-up
Replies: 18
Views: 2032

Re: Differential in elevator set-up

Ok, so if I put my rates in the input side for dual rates to get differential should I use differential % on the mix page? Another question. To get my elevator servos to track the same should I use a curve to get them to follow the stick movement the same. I put the rates on the mix page it kinda wo...
by heliperry
Fri Feb 14, 2020 1:16 pm
Forum: The FRSKY Forum
Topic: Differential in elevator set-up
Replies: 18
Views: 2032

Re: Differential in elevator set-up

Are you saying on the enput page side or mix page?
by heliperry
Fri Feb 14, 2020 12:08 pm
Forum: The FRSKY Forum
Topic: Differential in elevator set-up
Replies: 18
Views: 2032

Re: Differential in elevator set-up

Ok, right now I have my rates on the enput side. I will remove them on the enput side a try your suggestion. Thanks again Mike I will let you know how it goes 😊.
by heliperry
Fri Feb 14, 2020 11:23 am
Forum: The FRSKY Forum
Topic: Differential in elevator set-up
Replies: 18
Views: 2032

Re: Differential in elevator set-up

Mike, after thinking more about your salutation it is more for programing high and low rates isn't it not programming differential?
by heliperry
Fri Feb 14, 2020 10:55 am
Forum: The FRSKY Forum
Topic: Differential in elevator set-up
Replies: 18
Views: 2032

Re: Differential in elevator set-up

Mike, the Aero works Extra 260 shows for throughs on low rates 12 degrees up and 16 degree down and high rates 18 degrees up and 24 degree down. This is why I'm trying to program Differential on the elevator. So to the answer to your question is yes I'm trying to get a high and low rate on the eleva...
by heliperry
Fri Feb 14, 2020 2:25 am
Forum: The FRSKY Forum
Topic: Differential in elevator set-up
Replies: 18
Views: 2032

Re: Differential in elevator set-up

Yes they move but they move equal distance. I'm running two elevator servos one o channel 3 and one on channel 7 . I'm trying to get differential on low rates to high rates. I've used mixes with no progress. I'm just stumped! Hope this helps. If not contact me again.
by heliperry
Thu Feb 13, 2020 11:41 pm
Forum: The FRSKY Forum
Topic: Differential in elevator set-up
Replies: 18
Views: 2032

Differential in elevator set-up

Ok, I'm really struggling on how to program Differential in my X12S open tx. I've been trying to get my IMAC plane programming done and I'm frustrated. I've read a reread the user manual on the Horus X10/X10S that I bought being told this would help me in understanding open tx. Well I've programed i...
by heliperry
Wed Jan 29, 2020 8:20 pm
Forum: The FRSKY Forum
Topic: Failsafe kinda of works
Replies: 3
Views: 810

Re: Failsafe kinda of works

Well I think I figured it out on the failsafe. Once I looked at the transmitter I started understanding what I was seeing. Thanks for your help. I'm sure I'll have more questions later but right now I'm good.
Thanks again.😁
by heliperry
Wed Jan 29, 2020 6:45 pm
Forum: The FRSKY Forum
Topic: Failsafe kinda of works
Replies: 3
Views: 810

Re: Failsafe kinda of works

I figured out the 2receiver bind last night thanks. Ok on the failsafe mode do you have both receiverd on at same time and set bind button for less than a second. One at a time?πŸ€” I'm still learning this new programming. I've got three IMAC planes I need to setup and I'm trying to to program one for ...
by heliperry
Wed Jan 29, 2020 1:05 pm
Forum: The FRSKY Forum
Topic: Failsafe kinda of works
Replies: 3
Views: 810

Failsafe kinda of works

Re: Failsafe test Post Tue Jan 28, 2020 1:41 pm I'm looking for some help with binding Two receivers to one IMAC plane. I'm using a RX8BR receiver to a redundancy BUS-10 for 8channels using two batteries for redundancy. Am also using a XM+ receiver as a redundancy back up for the receiver. First que...
by heliperry
Tue Jan 28, 2020 6:41 pm
Forum: The FRSKY Forum
Topic: Failsafe test
Replies: 6
Views: 1556

Re: Failsafe test

I'm looking for some help with binding Two receivers to one IMAC plane. I'm using a RX8BR receiver to a redundancy BUS-10 for 8channels using two batteries for redundancy. Am also using a XM+ receiver as a redundancy back up for the receiver. First question...when binding these receivers do I need t...
by heliperry
Thu May 02, 2019 7:11 pm
Forum: The FRSKY Forum
Topic: Matching dual elevator
Replies: 4
Views: 1298

Re: Matching dual elevator

I just got back to this post, I think I'll try your suggestion.
Thanks Mike, sorry for not getting back so soon. I'm not able to get this site to bing me when I have a reply.
by heliperry
Sat Apr 20, 2019 2:37 pm
Forum: The FRSKY Forum
Topic: Matching dual elevator
Replies: 4
Views: 1298

Matching dual elevator

Ok, I'm stumped. I'm trying to match my dual elevator movement while setting up my throws. They match at 0, +100, -100% but when I reduce my throws per plane manual they won't track the same. I'm running open tx in a Horus X12S. I've got one left servo on channel 3 and right on channel 10. I'm runni...
by heliperry
Sat Mar 30, 2019 5:13 pm
Forum: The FRSKY Forum
Topic: Monitor page.
Replies: 2
Views: 937

Re: Monitor page.

Ok, that makes sense. Thanks 😊
by heliperry
Sat Mar 30, 2019 4:36 pm
Forum: The FRSKY Forum
Topic: Monitor page.
Replies: 2
Views: 937

Monitor page.

Hey guys, I have the Horus X12S Opentx. I've been setting up my new IMAC plane and was wondering. When I set my elevator servos in the right direction. The monitor page shows the two channel's being used to control the left and right servos move in opposite directions. Is there a way to get the moni...
by heliperry
Sun Mar 10, 2019 1:56 am
Forum: The FRSKY Forum
Topic: Failsafe test
Replies: 6
Views: 1556

Re: Failsafe test

That's what I was thinking also. At least with this dual receiver setup I can have half of the airplane on each receiver and if one fails I should be able to land the plane safely.
by heliperry
Sun Mar 03, 2019 9:50 pm
Forum: The FRSKY Forum
Topic: Failsafe test
Replies: 6
Views: 1556

Re: Failsafe test

Mike, I tried what you suggested. It did go to failsafe. But what I'm trying to decide is what is the advantage of running an RB-20 redundancy over just running the 2 Receiver's directly to batteries bypassing the RB-20. Any input on this?
by heliperry
Tue Feb 26, 2019 4:50 pm
Forum: The FRSKY Forum
Topic: Failsafe test
Replies: 6
Views: 1556

Re: Failsafe test

Mike, Ill give that a try.
Being I'm still in the testing mode before it goes into my plane I'll see if that will work. I'm not sure if I changed receiver numbers when I bound two together in my initial test, I'll have to check it out.
by heliperry
Sat Feb 23, 2019 4:24 pm
Forum: The FRSKY Forum
Topic: Failsafe test
Replies: 6
Views: 1556

Failsafe test

Hi guys. I'm going to be running two X8R receivers with a dual power dual receiver redundancy R8-20 to get 9+ channels in my IMAC plane with a Horus x12s Opentx. I'm new to this so I'm looking for some input on how to do a failsafe test on the set up before installing it in the plane. I have a test ...
by heliperry
Thu Feb 14, 2019 12:41 pm
Forum: openTx
Topic: Input page in a Horus x12s tx
Replies: 2
Views: 489

Re: Input page in a Horus x12s tx

That's what I was thinking but I was over thinking it. Thanks.
by heliperry
Wed Feb 13, 2019 12:34 pm
Forum: openTx
Topic: Input page in a Horus x12s tx
Replies: 2
Views: 489

Input page in a Horus x12s tx

I know this is probably a dumb question, but I'm going to ask. When you open the program page in the transmitter, the input page comes up with your basic controls. Question is on the Input page do you need to have the same number of inputs as you have on the mix page? Say you make more mixes for dif...
by heliperry
Sun Feb 10, 2019 9:47 pm
Forum: The FRSKY Forum
Topic: Mixing elevator to left and right aileron
Replies: 17
Views: 2150

Re: Mixing elevator to left and right aileron

That works on the mix I think. So, just in case I'm going to to loose this program I have so far. I'm going to hand program it to my test plan in the transmitter so I can remember how I did this. Each time I go out of companion it says failure to save. So I'm going to try what you suggested.
by heliperry
Sun Feb 10, 2019 7:11 pm
Forum: The FRSKY Forum
Topic: Mixing elevator to left and right aileron
Replies: 17
Views: 2150

Re: Mixing elevator to left and right aileron

Rdenchurch, how do you get this format of programing.
+= Ail Weight(15) Function(|x|) AilCor
I'm not sure how to do this.

Go to advanced search