Search found 27 matches

by fxshoppe
Wed Jan 09, 2019 5:04 pm
Forum: er9x
Topic: ArduVoice-9x Voice Module with Arduino for the 9x Radio
Replies: 556
Views: 72754

Re: ArduVoice-9x Voice Module with Arduino for the 9x Radio

Hey, good news.. well done, wonderful.. I haven't messed with this again since I wrote the first post. I have only one radio with stock board and it has an arduvoice inside.. But I have no reason to open it as it is working well.. :) I know that this voice module can be problematic sometimes. I spe...
by fxshoppe
Wed Jan 09, 2019 4:47 pm
Forum: er9x
Topic: ArduVoice-9x Voice Module with Arduino for the 9x Radio
Replies: 556
Views: 72754

Re: ArduVoice-9x Voice Module with Arduino for the 9x Radio

Wait a second, why did your radio say "Radio battery low"? Was the battery empty? Have you set an alarm for the radio battery? What firmware do you have installed on the radio?? João Er9x pr822 (test version of 128 bit proc) Some teething issues need to fix :D Have connected a 12v charger as was to...
by fxshoppe
Wed Jan 09, 2019 4:42 pm
Forum: er9x
Topic: ArduVoice-9x Voice Module with Arduino for the 9x Radio
Replies: 556
Views: 72754

Re: ArduVoice-9x Voice Module with Arduino for the 9x Radio

Houston success at last Compiled both the bootloader and program merged it to hex file as suggested. The promini was not happy with twisted pair wires between card reader and promini. Have not connected amp but a direct speaker to pin 5 (not pin 6 as posted earlier) and ground & voila have voice, t...
by fxshoppe
Wed Jan 09, 2019 3:09 pm
Forum: er9x
Topic: ArduVoice-9x Voice Module with Arduino for the 9x Radio
Replies: 556
Views: 72754

Re: ArduVoice-9x Voice Module with Arduino for the 9x Radio

Houston success at last Compiled both the bootloader and program merged it to hex file as suggested. The promini was not happy with twisted pair wires between card reader and promini. Have not connected amp but a direct speaker to pin 6 and ground & voila have voice, trims working, backup & restore ...
by fxshoppe
Sun Jan 06, 2019 7:14 pm
Forum: er9x
Topic: ArduVoice-9x Voice Module with Arduino for the 9x Radio
Replies: 556
Views: 72754

Re: ArduVoice-9x Voice Module with Arduino for the 9x Radio

The required fuses are described in the "instructions.pdf" file on Github for the amod. 1. The '128 is running at 5V. What voltage is your promini running on? If 5V, with a level converter to the SD card, then these connections are OK. 2. OK, but make sure the fuses don't then try to start in the b...
by fxshoppe
Sun Jan 06, 2019 5:41 am
Forum: er9x
Topic: ArduVoice-9x Voice Module with Arduino for the 9x Radio
Replies: 556
Views: 72754

Re: ArduVoice-9x Voice Module with Arduino for the 9x Radio

Rather naive questions but is it a possibility that 1 connect the pin 27 of atmega128 to D1 of promini & pin 28 of atmega128 to D0 of promini - no diode in between 2 Burn only the finalserial16 hex to the promini not install the optibootloader something like https://openrcforums.com/forum/viewtopic....
by fxshoppe
Sun Jan 06, 2019 1:30 am
Forum: er9x
Topic: ArduVoice-9x Voice Module with Arduino for the 9x Radio
Replies: 556
Views: 72754

Re: ArduVoice-9x Voice Module with Arduino for the 9x Radio

It's been some time since I did anything with this, and I've only ever used the Megasound board, not the Arduvoice build, and I run at 12MHz. When you put the optiboot bootloader on, are you changing the fuses to set the boot size to the smaller size? Mike Yes please I have set the fuses to low_fus...
by fxshoppe
Sat Jan 05, 2019 7:28 pm
Forum: er9x
Topic: ArduVoice-9x Voice Module with Arduino for the 9x Radio
Replies: 556
Views: 72754

Re: ArduVoice-9x Voice Module with Arduino for the 9x Radio

er9x uses 38400 baud to communicate to the serial voice module. Thought So Do you have the module connected to the radio when trying to upload the firmware at 38400? Nothing 6 pairs of wire connected between arduino and ftdi Mike At times it gets frustating but new territories learnt have compiled ...
by fxshoppe
Fri Jan 04, 2019 12:57 pm
Forum: er9x
Topic: ArduVoice-9x Voice Module with Arduino for the 9x Radio
Replies: 556
Views: 72754

Re: ArduVoice-9x Voice Module with Arduino for the 9x Radio

Just to add what is being tested Amp working fine connected ground to beeper point and signal to pin 3 of lm386 -- working Card reader connected to nano with same pin connection as promini,uploaded a sketch TMRpcm library --- card reader working Fed the output of nano sound input to amp output --wor...
by fxshoppe
Thu Jan 03, 2019 10:54 am
Forum: er9x
Topic: ArduVoice-9x Voice Module with Arduino for the 9x Radio
Replies: 556
Views: 72754

Re: ArduVoice-9x Voice Module with Arduino for the 9x Radio

Yes, you may ignore all the "dereferencing type-punned pointer" warnings. Mike Thanks mike, Sorry for trouble how can i create a combined firmware with both bootloader and serial voice together. My current build bat file is what needs to be added more cd C:\OpenAVRc\amod\obj Path C:\OpenAVRc\AVR-GC...
by fxshoppe
Thu Jan 03, 2019 3:54 am
Forum: er9x
Topic: ArduVoice-9x Voice Module with Arduino for the 9x Radio
Replies: 556
Views: 72754

Re: ArduVoice-9x Voice Module with Arduino for the 9x Radio

Hi Mike, Maybe off topic but when trying to compile the source from git hub https://github.com/MikeBland/mbtx/tree/master/amod i am getting these warnings. Unfortunately cannot decode if these warnings can be ignored. Since there are so many versions therefore giving it a shot. Also how can I get a ...
by fxshoppe
Wed Jan 02, 2019 4:27 pm
Forum: er9x
Topic: ArduVoice-9x Voice Module with Arduino for the 9x Radio
Replies: 556
Views: 72754

Re: ArduVoice-9x Voice Module with Arduino for the 9x Radio

I flashed your document.eepe file onto my radio. This is what I did to get the voice running with your Eeprom setup: Power on the radio in maintenance mode, that is, power on with left horizontal trim left (and released) . You will shortly see a message of "Hardware menu enabled" In Radio setup - h...
by fxshoppe
Wed Jan 02, 2019 2:43 pm
Forum: er9x
Topic: ArduVoice-9x Voice Module with Arduino for the 9x Radio
Replies: 556
Views: 72754

Re: ArduVoice-9x Voice Module with Arduino for the 9x Radio

Hi do not intend to connect a ftdi adaptor ever can i bypass the diode D1 between D0 and pin 28 of the processor and connect the wire directly to D0(RX) pin of the processor. Why am suspecting the diode because sd card or module could have issue but atleast trims should work. If need will ever arise...
by fxshoppe
Wed Jan 02, 2019 3:58 am
Forum: er9x
Topic: ArduVoice-9x Voice Module with Arduino for the 9x Radio
Replies: 556
Views: 72754

Re: ArduVoice-9x Voice Module with Arduino for the 9x Radio

Thanks a ton for all your help,

I will try and get back to you once i am able to check it on my tx.
by fxshoppe
Tue Jan 01, 2019 4:13 am
Forum: er9x
Topic: ArduVoice-9x Voice Module with Arduino for the 9x Radio
Replies: 556
Views: 72754

Re: ArduVoice-9x Voice Module with Arduino for the 9x Radio

Thanks mate, Happy new year. Done all the config settings as told in forum and as suggested by you. I have ordered components for amplifier and will rebuild as have checked each connection on amp board and apart from 10 ohm resistor to 150 ohm nothing changed. Only sound i can listen is puck sound f...
by fxshoppe
Sun Dec 30, 2018 3:09 pm
Forum: er9x
Topic: ArduVoice-9x Voice Module with Arduino for the 9x Radio
Replies: 556
Views: 72754

Re: ArduVoice-9x Voice Module with Arduino for the 9x Radio

Thanks for the reply. Kindly find the firmware used,config file as attached. My apologies the trottle trim is not working in the hw detect or in screen got confused with left and right side while inversing. The things i have done is removed the resistors from pin 27 and 28 and run direct wire from b...
by fxshoppe
Sun Dec 30, 2018 3:50 am
Forum: er9x
Topic: ArduVoice-9x Voice Module with Arduino for the 9x Radio
Replies: 556
Views: 72754

Re: ArduVoice-9x Voice Module with Arduino for the 9x Radio

I have removed the beeper and the associated transistor and connected to the arduino. I am not able to backup, the backup progress bar doesnot goes ahead.

Cannot hear any beeps either or any sound on any change.

Thanks and regards,
Amit
by fxshoppe
Wed Dec 26, 2018 2:36 pm
Forum: er9x
Topic: ArduVoice-9x Voice Module with Arduino for the 9x Radio
Replies: 556
Views: 72754

Re: ArduVoice-9x Voice Module with Arduino for the 9x Radio

Thanks no beep or anything as i had removed the stock beeper.

Only sound is the speaker puck when it powers up.

I will post eeprom once i am home where i have the USBASP to dump it. Though I have the radio and soldering iron and components so if anything needs to be done can do.

Thanks and regards
by fxshoppe
Tue Dec 25, 2018 11:41 am
Forum: er9x
Topic: ArduVoice-9x Voice Module with Arduino for the 9x Radio
Replies: 556
Views: 72754

Re: ArduVoice-9x Voice Module with Arduino for the 9x Radio

The trims are working so assuming that firmware is working fine and the communication between atmega 128 and promini is working fine
by fxshoppe
Tue Dec 25, 2018 9:07 am
Forum: er9x
Topic: ArduVoice-9x Voice Module with Arduino for the 9x Radio
Replies: 556
Views: 72754

Re: ArduVoice-9x Voice Module with Arduino for the 9x Radio

Hi Merry Christmas Finally built this but no sound also when try to backup model the progress bar is not going ahead so can i assume sd card is bad. What is the maximum sd card it supports as I have 32 GB ones apart from 1GB which am testing with. Also using r11 150 ohms instead of 10 ohm r8 47K ins...
by fxshoppe
Thu Nov 01, 2018 3:49 pm
Forum: Hardware Mods
Topic: Flash M128 Turnigy 9x
Replies: 19
Views: 1602

Re: Flash M128 Turnigy 9x

Friend

You need to first burn fuses if you have changed processor.

Then write the firmware, the option you are mentioning is different green chip.

Ignore the usbasp firmware error

Ping me if you need further assistance.

regards
by fxshoppe
Tue Sep 18, 2018 10:10 am
Forum: er9x
Topic: er9x development
Replies: 3106
Views: 350259

Re: er9x development

Ok, your choice.. :) The extra RAM of the m2561 is really welcome as it allows for features not possible on the m128. Er9x supports way more extra hardware than opentx, which only supports a parallel voice module as far as I know. Also, development for this board seems to have stopped. Er9x continu...
by fxshoppe
Mon Sep 17, 2018 7:27 am
Forum: er9x
Topic: er9x development
Replies: 3106
Views: 350259

Re: er9x development

You could have upgraded to the m2561 instead. It has the double of the RAM as well. I believe it also has a couple more pins that can be used for extra switches.. João Honest answer :D 1 had Atmega 128 in hand instead of waiting for 40-50 days and possible package lost from China. 2 Wanted to be fl...
by fxshoppe
Sun Sep 16, 2018 4:22 am
Forum: er9x
Topic: er9x development
Replies: 3106
Views: 350259

Re: er9x development

Thanks Mike, Compile script works fine, need to validate oled Waiting on parts from china. Have upgraded the 9x from atmega 64 to atmega 128 next step serial voice. Only challenge left is that frsky dashboard connects to bluetooth but no data using a rs232 to ttl converter and level sifter for inter...
by fxshoppe
Fri Sep 14, 2018 5:01 am
Forum: er9x
Topic: er9x development
Replies: 3106
Views: 350259

Re: er9x development

Thanks Mike, Please do not make any changes just for me. I downloaded the avr-gcc (GCC) 4.8.0 20130306 (experimental) version and compile didn't show any error except at avr-size stage which i replaced with from version 4.9 and no error. I understand avr-size is only used to show firmware size and h...
by fxshoppe
Thu Sep 13, 2018 3:52 am
Forum: er9x
Topic: er9x development
Replies: 3106
Views: 350259

Re: er9x development

While executing make CPU=128 EXT=FRSKY PHASES=YES I am getting cat: prov.txt: No such file or directory menus.cpp: In function 'void menuBackupRestore(uint8_t)': menus.cpp:5472:12: warning: large integer implicitly truncated to unsigned type [-Woverflow] p[11] = sizeof(g_model) ; ^ menus.cpp:5532:37...
by fxshoppe
Sat Sep 08, 2018 4:03 am
Forum: erskyTx (was ersky9x)
Topic: ERSKY9X Coding
Replies: 4455
Views: 363782

Re: ERSKY9X Coding

Hi Mike and others, Firstly thanks for this wonderful work. My aim is to club features spread over er9x and opentx ( if allowed to say here) Ultimate output 1 support for cheap 1306 and 1106 display i2c and spi version (er9x supports spi but not i2c, OpenAVRc supports oled), even 7920 2 Support for ...

Go to advanced search