Search found 15 matches
- Sun Nov 11, 2012 5:31 pm
- Forum: er9x
- Topic: Cannot get TRAINER to work - help
- Replies: 21
- Views: 9763
Re: Cannot get TRAINER to work - help
I agree, I have a cheap Chinese USB something, true... but works with my Spektrum DX6i, as said. I will build the interface - thanks for the link! I played "PPM delay" and left "PPM frame lenght" to default 31 mSec. The range that PPM works on my USB and Simulator is between 300 ...
- Sun Nov 11, 2012 9:19 am
- Forum: er9x
- Topic: Cannot get TRAINER to work - help
- Replies: 21
- Views: 9763
Re: Cannot get TRAINER to work - help
I did new mix on ch5=aileron - and I can see it in my FMS as ch6 - so that I can use. But, stil wondering - why ch1 in not working? I have MODE3 AETR er9x. I tryed to PROTO=PPM=4ch - but ch1 stil dead and I cannot see my mixed ch6. When and use PROTO=PPM=6ch I can see my mix (mix=ch5=AIL, but I see...
- Sun Nov 11, 2012 8:49 am
- Forum: er9x
- Topic: Cannot get TRAINER to work - help
- Replies: 21
- Views: 9763
Re: Cannot get TRAINER to work - help
I did new mix on ch5=aileron - and I can see it in my FMS as ch6 - so that I can use. But, stil wondering - why ch1 in not working? I have MODE3 AETR er9x.
- Sun Nov 11, 2012 7:56 am
- Forum: SMARTIEPARTS PROGRAMMER
- Topic: TH9X show after burning attempt "Eeprom Error"
- Replies: 6
- Views: 7080
Re: TH9X show after burning attempt "Eeprom Error"
latest. both.Kilrah wrote:Which version of eepe and er9x?
- Sat Nov 10, 2012 7:22 pm
- Forum: er9x
- Topic: Cannot get TRAINER to work - help
- Replies: 21
- Views: 9763
Re: Cannot get TRAINER to work - help
POS - works- except ch1, NEG doesn't work at all. (on PC)MikeB wrote:For the simulator, try changing the SHIFT from POS to NEG (or NEG to POS).
Mike.
- Sat Nov 10, 2012 5:35 pm
- Forum: er9x
- Topic: Cannot get TRAINER to work - help
- Replies: 21
- Views: 9763
Re: Cannot get TRAINER to work - help
True !
I had to swap connector markings. Look at the picture - if connected by color - it's WRONG. When it's connected as in picture - works. How stupid is that. Who would think...
what about ch1 not working on PC simulator? also both tx's
I had to swap connector markings. Look at the picture - if connected by color - it's WRONG. When it's connected as in picture - works. How stupid is that. Who would think...
what about ch1 not working on PC simulator? also both tx's
- Sat Nov 10, 2012 4:47 pm
- Forum: er9x
- Topic: Cannot get TRAINER to work - help
- Replies: 21
- Views: 9763
Re: Cannot get TRAINER to work - help
Went to shop, bought two MONO jacks and cable. ...and.... IT WORKS!!! lol. Thansk for all support. Learned few thing in meantime. STEREO JACK doesnt' work for TRAINER!!! Also that 1kohm mod in obsolete. Verified. And that backlight mod with pin3 and cut to pin5 also works. any idea why ch1 is not wo...
- Sat Nov 10, 2012 2:28 pm
- Forum: er9x
- Topic: Cannot get TRAINER to work - help
- Replies: 21
- Views: 9763
Re: Cannot get TRAINER to work - help
Did. Bars don't move. I also try'd put MODEL07 (new model) TRAINER=ON on the Trainer tx (master). In meantime I downloaded SoundCard Osciloscope ( http://www.sillanumsoft.org/download.htm ). When I connect TX to PC soundcard I can see square signal (with tx turned off). When I turn TX on, the signal...
- Sat Nov 10, 2012 1:56 pm
- Forum: er9x
- Topic: Cannot get TRAINER to work - help
- Replies: 21
- Views: 9763
Re: Cannot get TRAINER to work - help
Try setting protocol on the student radio to PPMSIM, and turning the radio on. The 1k resistor mod is obsolete, this is what should be used instead. What cable are you using? Done PPMSIM on student. Not working :( Even bridged the resistor mod - the same. Not working. When I switch THR switch, dedi...
- Sat Nov 10, 2012 1:05 pm
- Forum: er9x
- Topic: Cannot get TRAINER to work - help
- Replies: 21
- Views: 9763
Re: Cannot get TRAINER to work - help
Do you see numbers moving on the Trainer screen on the master radio? No. That's the problem. What do you have on the mixer screen of the slave TX? hm??? I have my normal mixes. If I use slave as standalone, I can operate the model airplane. The same on master. Mixes are general - basic 4ch mix with...
- Sat Nov 10, 2012 10:52 am
- Forum: er9x
- Topic: Cannot get TRAINER to work - help
- Replies: 21
- Views: 9763
Cannot get TRAINER to work - help
I have two er9x moded TXs. both the same version, both 1k resistor mod, both backlit mod(with transistor and pin5 pcb cut). I switch on the master tx and connect with stereo cable to slave tx that is turned off. I have TRAINER ON in my model settings on master tx I have this setting on master TX und...
- Fri Nov 09, 2012 10:08 am
- Forum: Electronic Mods
- Topic: hk backlight mod
- Replies: 204
- Views: 110844
Re: hk backlight mod
I would like to make a Low Voltage Drop regulator mod. I haven't foind any info so I try to do it mayslef. I'll replace stock 5V regulators with LowVoltageDrop one because I use 2S LiIon battery and this way I'll get more use of it, since the voltage can be lover and TX will stil operate than with s...
- Thu Nov 08, 2012 10:11 pm
- Forum: SMARTIEPARTS PROGRAMMER
- Topic: TH9X show after burning attempt "Eeprom Error"
- Replies: 6
- Views: 7080
Re: TH9X show after burning attempt "Eeprom Error"
I have this error after sending to TX:
If I use Companio9X it works ok.. so it is not my HW problem.
And after all - my TX is working as well... just this error - I cannot write models to TX.
If I use Companio9X it works ok.. so it is not my HW problem.
And after all - my TX is working as well... just this error - I cannot write models to TX.
- Thu Nov 08, 2012 9:34 pm
- Forum: companion9x
- Topic: Editing model configs
- Replies: 2
- Views: 2490
Re: Editing model configs
I get confused everytime I read this: 1: "Retreive calib. and HW setting from profile" and 2: "Store calib. and HW settings in selected profile" because it is not in English. It is a direct translation, I assume, from Czech... and I never know what is read from where and stored w...
- Thu Nov 08, 2012 8:55 pm
- Forum: companion9x
- Topic: Guided model configuration
- Replies: 83
- Views: 44966
Re: Guided model configuration
Not sure this is the place to say this, but when I use the wizzard, it does not take my receiver order (AETR. ...,...) into account and always uses the same channel distirbution.
Other than that - it's a great tool ! Better than templates alone.
Other than that - it's a great tool ! Better than templates alone.