openrcforums

MikeB wrote: ↑Tue Mar 10, 2020 3:45 pm Up LONG is "press the up button and hold it for a second, a long press", this gets to the statistics menus.
"then LEFT" is "press the left button to change the displayed screen.

Mike

Sorry should have said, what is the Boot Reason Screen ????

If you have a 9XR-PRO, then you have 512K of flash. You need to flash ersky9xr_rom.bin (note the small "r"). To check what chip you have, go to the "BOOT REASON" screen (Up LONG then LEFT), the chip ID is shown on the bottom line as 8 characters, should be 28AB 0A60 on the 'PRO....

that did it, really dense. I thought you had to signify each position of the switch, ergo mixing line SBup/SBmid/SBdn
I did not know it would ASSUME that, great now works with the least mixing, just SB as source, NO switch tab designations, and SLOW works

thanks much

sorry feel dense, how can you have three (3) weights 100,0,-100 within one mixer line

I tried using SWITCH (SB) as a source
weight as -100, 0, -100 and switch SBup, SBmid, SBdn respectively
(still do not understand why 100,0,-100 does not work)
this does not allow SLOW to work

why would you use OFFSET and DIFF, to complicate
why would that make SLOW work

Thanks, THIS works (using REPLACE)
I did have weights of 100,0,100 and it worked at moving the FLAPS right, just could not SLOW it
(also don't understand why third weight is 100 instead of -100)
how would offset and diff be used, with weight, and why???

I have flaps programmed on my 9XRPRO, and I have SLOW of 2s up and down use logical switches L1, L2, L3 with ELE and AIL switches to activate up(!ELE+!AIL)/mid(ELE+!AIL/dn(ELE+AIL) this works fine and 2.0s delay works fine going up and down same programming on QX7S and X9DP, only using SB (3pos), up...

thanks again MIKE that really seals the deal, love this program

By the way, OpenTX (latest versions) does not work with Multiprotocol Module and DSM protocol, at least not for me It also doesn't work with 9XRPRO. So I am a firm ERSKYTX convert, I like everything almost better. Just miss the notes in OpenTX, the note screen would come up before the model screen a...

I checked and the audio file WELCOME is short circuiting too, so its the audio file, will work on this

worked AGAIN, many thanks my 9XRPRO uses the right enter button, so I was really confused I now have ERSKY9x working on ALL three transmitters, (9XRPRO, X9DPLUS, QX7S) with JNP4N1 modules. I can pick any transmitter (one at a time for sure) turn it on, and without rebinding, control all my Airplanes...

Fantastic thanks very much Mike that worked to get models onto Radio, had no idea they were not supposed to be in EEPROM folder Just left with one last issue, when I go into maintenance mode and select EEPROM the two choices BACKUP EEPROM, RESTORE EEPROM neither works, just hangs up the transmitter,...

well something is wrong here and cannot figure out. Have reprogramed x7_rom.bin V221 multiple times, EEPROM still will not work when I go to maintenance mode the EEPROM tab will not work, cannot BACKUP or RESTORE EEPROM, just locks up also when ERSKY9x starts the starting voice cuts off and does not...

Just loaded ersky9x FW 221 on my Taranis QX7S, and it is working got bootloader loaded too however, the SD CARD will not take/show EEPROM (Models) I tried write memory from eepskye and it said it was successful, shows bin file in EEPROM folder however, no models show up in main screen, just MODEL01 ...

Mike
[/quote]
I just installed eepeinstall, and eepe works, but eepesky starts with a UART screen, and nothing on the screen, works
scan, start, whatever

thus I cannot start the eepesky program, what is wrong here

jhsa wrote: ↑Wed Oct 09, 2019 9:32 pm I think your radio is not being supported by OpenTX anymore. I suggest you try ErskyTX (former Ersky9X).

João

they list the turnigy 9xrPRO under radios supported, on opentx

I installed 2.3.1. On Turnigy 9XR PRO. And their is no radio calibrate tab. Sticks under hardware tab is blank cannot be accessed

Anyone have same problem

can you give me any more info, need to sign up for this, what is it, what do I do their
is it the developers site
you show 9XRpro do you use opentx 2.2.2 with it???

Well I guess I anuswered my own question Only inputs I1-I4 work with a 9XR PRO radio configuration in 2.2.2 Have to put the input lines you would have used, into mixes tab I5-I8 This is a very significant failure; is their place where this has been documented. Opentx advertises compcatible with 9XR ...

Can anyone verify this is working for them Opentx 2.2.2 and Turnigy 9XR Pro.profile radio None of the inputs after I1-I4. Seem to be working HOLD WHATER EVER I program for I5-I8.(thr input for pitch cutie) works until Insave the model file Then close and reload the model file it has changed (thr) to...