openrcforums

Hi all, I have a turnigy 9xr pro running firmware: ersky9x-pf8r221 Transmitter module is Frsky DJT and receiver is Frsky D8RII plus I am trying to setup PPM to work so it can control a custom bait boat using a control board from SP Tackle, I have attached there manual, UCB Specification Manual Issue...

Hi all, I'm probably stupid but I having an issue I want to pull left thumb stick to the right and it activate a relay but only for like a 0.5 sec pulse, what settings would I need to change?

Thanks

Hi, think I have managed to fix all Issues except for one. I am using the Turnigy 9XR Pro with FRSky DJT module I have setup the 3 position switch for different flight modes Up is Loiter Middle is Normal Down is Auto This shows the modes on the LCD display in top right corner, but have set a further...

Think it was radio module


Sent from my iPhone using Tapatalk

I have just been playing around with various settings to get telemetry working, and for some reason as soon as I turn the handset on it start to beep and constant, please can someone tell me what it is and how to turn off.

Thanks John

Hi, I am trying to activate a timer when the right stick is moved in any direction as this is the motor controls for my boat, which is set as ele and ail

Any ideas? thanks John

Fixed the issue, for some reason one of the ESCs had a jumper that was set on NIMH rather than LIPO, also removed the brake function so its just forward and reverse I also swapped a wire on the motor so they spin in opposite directons as props are handed. So really only thing I need to do now is sho...

Hi, think I am getting there with the mixing, for some reason one is on 100% and the other only 50% to get the same sort of thrust, don't think this is right but not sure. I am trying to get my FrSky Battery Voltage Sensor to send voltage back to the handset so I know when it reaches say 11v bring b...

Any ideas?


Sent from my iPhone using Tapatalk

Have not changed anything, just uploaded your file, also should I turn the ESCs so there is no brake function or leave it as it is with Forward, Brake, Reverse?

Hi João Both motors are connected exactly the same way, Left Motor / ESC is Channel 1 Right Motor / ESC is Channel 2 When stick is center and boat is turned out power goes to ESCs and they initialize, yes, here is manual link for them https://hobbyking.com/media/file/q/u/quicrun_60a_brushed_esc_manu...

Also, would there be any reason why one ESC sounds like its putting more power to one motor as in maximum throttle is louder on one side than other which can't be helping the situation, just getting more puzzled on what to do

Thanks John

Hi, ok think I have sorted out issue 2 and 3 except I need to reverse one of the ESC's as when trying to go forward one propellor spinning in reverse if this makes sense. So how do I get props to work correct?

Hi João, Ok here is what I have found when using this so far. 1. Switch Warning AIL, but when the switch is in down position lights are off, should this be reversed so that off is up and on is down? 2. When the left stick is held to left this drops the hopper like it should, thank you, but lights do...

No problem thank you


Sent from my iPhone using Tapatalk

Ok how do I plug the lead on switch into 2 channels on receiver when it only has one
Lead? Thought switch plugs into 1 channel only


Sent from my iPhone using Tapatalk

Thank you

Can't see the upload file, so here it is again with a new file name

Hi João, sorry I was away fishing. Here is model file, I have been thinking while away, the left thumbstick currently when holding left or right does the hook release, I am scraping this as will not be using it, will only be using the hopper drop left and right so would like this on the left stick t...

Have plugged in, currently there is power the whole time through the switch unless I flick 3 pos switch to ID0 power goes off it should be reverse of that

Also when switched to middle
Position or ID2 it should have no power, hope this make sense


Sent from my iPhone using Tapatalk

Hi again ok all working on my bait boat apart from the hopper droppers, I have purchased an 2 way receiver controlled switch, it has one plug for receiver so only uses one channel I have attached wiring diagram which I have wired up, but doesn’t seem to drop, think programming not quite correct, It ...

It’s mainly for Gps and plotting exact location, say if putting bait out in middle of night you want to be on exactly the same place, the Pixhawk I thought was one of the best ones and at good price


Sent from my iPhone using Tapatalk

Hi again, everything working as it should, I am now going to be adding a Pixhawk 4 Flight Controller, do i need to do much on the handset for this to work or it mostly done through Mission Planner?

Just waiting for the kit to turn up next week.

Thanks John

Yes, have done them all now, had to use custom names and not numbers, At present you programmed ID0 and ID2 as hopper droppers, is there much to do if I want to change them to the left stick up and down? As I may be adding a motor winch at some point for underwater camera and will need the ID0 and I...

Hi João, Ok, everything seems to work fine for now without changing anything. Issues I am now having are getting voicefiles to play when hook left and hook right are dropped, also when I startup handset I would like it to say my voicefiles when handset or model is turned on. Would like voice file fo...

Sorry, I re-imported and notes are now there, so strange. At present lights flash before the doors actually open, as it seems as soon as rudder (left stick) moved to left or right the lights start to flash, but because need to hold stick for 3 secs to activate lights may flash and think bait is drop...

Quick update everything looks perfect, might set hopper release on left stick like hook release, but just letting you know that I do not have any notes showing in mixes, any ideas as to why not? Trying to set a voice name for BAITBOAT model but cannot add a name can only select a number, did make a ...

Take that back have imported by load model settings, thank you will test and get back to you. thanks again

Hi João, I have tried to open this file but doesnt seem to do anything,

I am using eepesky not eepe as seems cannot get eepe to connect to transmitter,

Any ideas? thanks John

Hi, here is my eepe sky file. Seems I am having following issues: 1. Trying to use CH4 As navigation lights on and off with Ail Switch, also trying to get voice to say Navigation Lights on and Off, have made voice fie but cant see where to add for my setup 2. Want Hopper left to drop when rudder lef...