Search found 14 matches

by ckambiselis
Sun Jun 10, 2018 6:44 pm
Forum: ersky9xr
Topic: 6POS switch adjust PWM value for each position?
Replies: 2
Views: 831

Re: 6POS switch adjust PWM value for each position?

I'm running 219, thanks for the heads up, didn't see those, gonna try fix it through there and post the numbers here in case someone else needs them, even though it might be a bit different for someone else. UPDATE: In the mixer I set the 6POS channel to use the 9 point curve I adjusted and the valu...
by ckambiselis
Sun Jun 10, 2018 6:12 pm
Forum: ersky9xr
Topic: 6POS switch adjust PWM value for each position?
Replies: 2
Views: 831

6POS switch adjust PWM value for each position?

Hi, It's finally vacation time again and I picked up from where I left my Talon built, I'm using Ardupilot and have installed a 6POS switch to my 9XR Pro for flight mode switching, the mode switching works pretty much fine but there is one problem I can't find a solution for, the difference of the P...
by ckambiselis
Sat Aug 19, 2017 9:30 am
Forum: ersky9xr
Topic: Manual calibration for 6POS switch?
Replies: 16
Views: 2561

Re: Manual calibration for 6POS switch?

Here are the wiring diagrams with the values switched.

Oscar
by ckambiselis
Fri Aug 18, 2017 9:58 pm
Forum: ersky9xr
Topic: Manual calibration for 6POS switch?
Replies: 16
Views: 2561

Re: Manual calibration for 6POS switch?

Got the hot air gun out and just swapped the first and the last resistors (1K with 2.2K), and it works perfect now. That connection diagram is actually very well made and I have saved it in my UAV folder for all the mods I'm making, and since it is the first thing that comes up when your search for ...
by ckambiselis
Fri Aug 18, 2017 9:29 pm
Forum: ersky9xr
Topic: Manual calibration for 6POS switch?
Replies: 16
Views: 2561

Re: Manual calibration for 6POS switch?

Those are not the connections that Ersky9x is expecting.. You have one pin floating (not connected). I suggest you modify your switch. You say you built it based on another design? For which radio is that switch you copied then? :o João EDIT: If you have the 4th pin not connected instead of the 3rd...
by ckambiselis
Fri Aug 18, 2017 7:50 pm
Forum: ersky9xr
Topic: Manual calibration for 6POS switch?
Replies: 16
Views: 2561

Re: Manual calibration for 6POS switch?

These are the readings shown on SwitchDiag 6P0-6P1-6P3-6P1-6P4-6P5, this is the sequence they appear when I go from start to end. This is the exact voltage reading sequence the output pin gives when I go from one end to the other 0.00-1.07-1.66-1.48-1.77-3.3. The schematic is made exactly as shown o...
by ckambiselis
Fri Aug 18, 2017 3:18 pm
Forum: ersky9xr
Topic: Manual calibration for 6POS switch?
Replies: 16
Views: 2561

Re: Manual calibration for 6POS switch?

watch this video.. it is in the Hardware menu.. https://www.youtube.com/watch?v=981zcTdqoNU&index=10&list=PL5uJhoD7sAKiuVp8c4vNw8vfxUB5C-mpr João If you mean the calibration he does on 10:30, I have done that already as I said, the HEX values are different for each position, what I want to change i...
by ckambiselis
Fri Aug 18, 2017 2:50 pm
Forum: ersky9xr
Topic: Manual calibration for 6POS switch?
Replies: 16
Views: 2561

Manual calibration for 6POS switch?

Hi, I just installed a 6POS switch for flight mode control and confirmed it works, kind of, I used an MR-K112 and set it to be a 6 position switch, I used the resistor values from the wiring diagram and made a custom milled pcb, installed the output to pin 2 of JR3, I set a 6POS source to AUX and ca...
by ckambiselis
Thu Aug 03, 2017 11:39 am
Forum: OpenLRSng
Topic: [SUPPORT] OpenLRSng support thread
Replies: 147
Views: 65412

Re: [SUPPORT] OpenLRSng support thread

Hi, I have been trying to set my OrangeRX OpenLRS TX and OpenLRSng RX for days and haven't been able to get them to work completely, I flashed both module with OpenLRSng (since I'm planning to use it with my Pixhawk and get Mavlink data), through the ISP port using the OpenLRSng-gitsly .ino and the ...
by ckambiselis
Wed Jun 07, 2017 6:39 pm
Forum: ersky9xr
Topic: Change left joystick operation "on the fly"?
Replies: 2
Views: 1327

Re: Change left joystick operation "on the fly"?

Hmmm got a little bit confused by the values, but if it's from the Mixes settings I will check the manual and figure it out.

Thanks
by ckambiselis
Tue Jun 06, 2017 10:16 pm
Forum: ersky9xr
Topic: Change left joystick operation "on the fly"?
Replies: 2
Views: 1327

Change left joystick operation "on the fly"?

Hi, Got a 9XR Pro a few days ago as I am ugrading my hexa from Naza to Pixhawk and I'm trying to find if there is a way to change the right stick (mode 2) from the classic controls to camera gimbal control on-the-fly using one of the switches, the idea is, I fly to the position I want leave the hexa...
by ckambiselis
Thu Jun 01, 2017 10:58 am
Forum: Turnigy 9XR PRO radio
Topic: 9XR Pro Wiring Info Q&A
Replies: 76
Views: 49221

Re: 9XR Pro Wiring Info Q&A

Took the connector board off, checked the connections all the way to the main controller, everything seemed ok, put everything back again and now it works, not sure if the board wasn't making perfect contact or something but it works fine now. For future reference, R46 and R48 are connected to D+ D-...
by ckambiselis
Thu Jun 01, 2017 8:18 am
Forum: Turnigy 9XR PRO radio
Topic: 9XR Pro Wiring Info Q&A
Replies: 76
Views: 49221

Re: 9XR Pro Wiring Info Q&A

Everything obvious has been checked.
by ckambiselis
Wed May 31, 2017 1:19 pm
Forum: Turnigy 9XR PRO radio
Topic: 9XR Pro Wiring Info Q&A
Replies: 76
Views: 49221

Re: 9XR Pro Wiring Info Q&A

Does anyone have a schematic of the main board, I found one at another forum but the link provided was not working anymore, I'm trying to find if any of the test points are for the USB connection, my computer isn't reacting in any way when I connect the USB cable, even though the radio does change f...

Go to advanced search