openrcforums

Hi Mike, yes was without rs232 mod. I have updated to latest non eu xjt firmware by simply remamed firmware file and tanaris exepted update. Now its a lot batter. So I am using external modul from turnigy 9x. Now I have all my planes and drone covered wth one tx. 😀. Later on I will use djt modul for...

Hi all! One question. I have taranis and with internal modul I get low rssi after 300 m or less. With 9x and djt modul mod done It worked a lot better. If I put djt modul to taranis do I need external wires for telemetry or it works with djt telemetry mode done for 9x? What settings do I choose for ...

It works also on latest er9x 9x with telemetry mode.
Rssi on osd is same as on lcd of tx.

Tnx, I am, was a little trick to get right telemetry data from frsky to tx but now all works ok.

Hi, update,all switches are also working.

Ok I think I now why lcd was flickering, so Im back to er9x.I am using 3s lion 2200 mah panasonic batteries. But I didnt calibrate voltage in tx....so they were completely below 3volts per cell... but tx was working and showing 9.5volts. I think that was it

Ok I think I now why lcd was flickering, so Im back to er9x.I am using 3s lion 2200 mah panasonic batteries. But I didnt calibrate voltage in tx....so they were completely below 3volts per cell... but tx was working and showing 9.5volts. I think that was it

I wrote to other threat... ok with er9x all mods works, telemetry audio, haptic. But when I go to settings menu highlighted item stays on same place if I navigate over menu and lcd flickers lightly. I can hear sound of navigation but highlighted item stats on same place...
With er9x switches work.

Hi when I have er9x-frsky switches work ok, BUT when I go to settings menu lcd flickers lightly and cant see changes to cursor menu I can hear sounds but highlighted item stays on same possition. I upgraded fw 2 times. It was same. So I went to opentx. There all works ok, exept switches. Telemetry, ...

Hello I have allmost same problem. I have telemetry mode done. telemetry works ok but thr cut and ail switches are not working. Works if both are on if one is off both are off. I have latest opentx with frsky, audio and haptic firmware. On er9x switches work ok. Any idea why is that so?

Yes Mike.

Hi, just to be sure..after telemetry mod thr cut and ail switches doesnt work right? They are now used for telemetry. When I turn both on both are on. If I turn one on stays off right?

Ok tnx for both answears!

I have modified frsky and 2 unmodified flysky. my other question is or was if I put unmodified frysky to modified tx. Reason is that I cant rebind my 2 planes to new flysky. I would need to dissasambe whole plane. So I have one stock flysky modul allready binded to this 2 planes. So can I use it in ...

http://openrcforums.com/wiki/index.php/ ... _Mod_FrSky
I did this mod. So can I use it also in unmodified rx? Or only in modified tx?
And also can I use modified Flysky mod in unmodified tx?

Hi!
One question. If I mod flysky tx module will it work in unmodified tx? Or do I need to use it only in modified tx? Thanks!
I would use it in both tx.
Thanks!

I have printed manual... Ok I did telemetry mode, updated to er9x-frsky and it shows tx rd strenght...😀😀 I used main board which was dead at my first attempt..of upgrading to er9x. I used osillator like before. 3rd main board I recived its damaged. Cant see atmega chip...so I debridged firts one and...

ok, I deleted flaperon mix and now aileron dual rates works. Strange...ok all works, this was test so I can put my gasier mxs-r and other biger models in hire and back to new board when its installed in flysky tx. And I need to upgrade old flysky board with new 128 so I can have telemetry in old com...

I forgot to delete them they are for flaperon but I deleted mix for elevator forgot to delete for ailerons.they doesnt matter for my dual rates.

Hire are settings where aileron 2 doesnt change rates in one dirrection in second is ok.

Sorry I meant sticks menu where I can set dual rates and see them all at once opentx has it. Its ok I will use it in mixer. I will upload tomorrow I left my avr cable at work...thank you!

Hi all! I tried er9x and I am missing curves menu, ok its in the mixer bur when I did dual rates, one aileron doesnt move to 100 on high and second does. End poins are set to 100 on high and 80 on normal. I have it on ele switch. Dual rates works till 90% of stick movement. High doesnt moves aileron...

ok so I will install er9x to my old tx and thats it... I had a problem with my models I think somethink about old firmware or something. I have 6 models on and a lot of mixings so I dont want to lose them. I use 2 tx modules one normal for smaller planes and one frsky ppm with telemetry for drone an...

OK tx works its tricky I needed to put ail swith to off again and also throtle cut to off. Then I downloaded er9 normal version but chip selected was m128 not er9-128 with m128 selected. Now it works. OK now I need open tx so its same as my other tx so I can teach my son to fly with student teacher ...

ok fuses writen are 0e, 81, FF. Is this ok that now it reads chip if oscillator is connected? It should read without now with fuses written right?
when I try to write fr er9-128 I get an error. I am stucked I think.

It WORKS! It did write fuses but it only writes firmware if 20mhz oscillator is connected. tx is still dead when I try to power up...fw is upgraded ok
Maybee wrong fuses? Any ideas now? Thanks!

Thank you very much Joao! I removed resistor and use thin wires across contacts. Can you confirm fuses I must write in.Are they correct?
Thank you again!I will try now...

ok so I take pictures of a programmer ok hire they are..

Hello Mike, I tried now, its same I tried all frequencies, same fault first missmatch at byte 0x0000. IS my 20MHZ oscillator to high frequency? <But now it does read chip and also fuses BUT oscillator needs to be on if its off it doesnt recognizes chip. Joao I dont know what pictures did you want re...

Joao sorry for that. Ok I was messing with driver thats why hire didnt recognized programmer. I made some progress since that. I put 20mhz oscillator and in avrude atmega 128 is recognized. I want to change fuses to default 0e, 89, ff but coudnt change them I get this. I think I need to find 1mhz os...