Does anyone know of a way to bind the S8R in non telemetry mode?
IE no telemetry from receiver...
This would make it work with redundancy bus
Search found 10 matches
- Mon Jan 15, 2018 2:47 pm
- Forum: Reviews
- Topic: Review: FRSKY S8R Receiver
- Replies: 22
- Views: 37226
- Mon Jan 15, 2018 2:33 pm
- Forum: General help (FrSky Taranis radio)
- Topic: Slider switches on Taranis sides ???.
- Replies: 9
- Views: 9354
Re: Slider switches on Taranis sides ???.
sorry about the delay 2.2 is the version
You cannot find them in drop down in most places
You cannot find them in drop down in most places
- Sat Jan 13, 2018 3:07 pm
- Forum: General help (FrSky Taranis radio)
- Topic: X** servo travel
- Replies: 2
- Views: 2345
Re: X** servo travel
Never mind I thought I was using a s8r and x8r but was using 2 s8rs and had not set limits by system reset
anyone know if telemetry can be disabled on S8R?
anyone know if telemetry can be disabled on S8R?
- Sat Jan 13, 2018 2:58 pm
- Forum: General help (FrSky Taranis radio)
- Topic: X** servo travel
- Replies: 2
- Views: 2345
X** servo travel
I just recently noticed something which is quite odd when I bind X series (includes S series as well) the servo stops moving when the value for the channel is about 70% I have verified this is not the servo limit by binding Spektrum receiver to the taranis with spektrum module.... The servo travels ...
- Wed Jul 19, 2017 1:37 am
- Forum: openTx for FrSky radios
- Topic: telemetry lost
- Replies: 1
- Views: 4709
telemetry lost
I am constantly getting telemetry lost telemetry recovered.... I have been flying with s6rs lately and haven't gone out with any x8r receivers for a while... Does anyone know if there is a s6r bug? or is there a seperate antenna for telemetry in the transmitter.. perhaps a loose connection I will st...
- Fri May 19, 2017 4:35 pm
- Forum: General help (FrSky Taranis radio)
- Topic: Slider switches on Taranis sides ???.
- Replies: 9
- Views: 9354
Re: Slider switches on Taranis sides ???.
Why are RS and LS not supported on TX companion?
- Mon May 01, 2017 5:30 pm
- Forum: openTx
- Topic: Sequencing
- Replies: 7
- Views: 5190
Re: Sequencing
Here is a new way WOW Lots of ways.... I really didn't have a full grasp on the logical switches or on MAX which I really wish they would just let you type in a value instead of having to mess with offset. but Hey. How am I to argue with the braniacs that came up with this stuff. logical switches Lo...
- Mon May 01, 2017 4:11 pm
- Forum: openTx
- Topic: Sequencing
- Replies: 7
- Views: 5190
Re: Sequencing
I really do appreciate the response and understand what you are saying but the real thing I am actually trying to do now is below. I was trying to simplify so I didn't have to explane Wow Edge is the answer though you got the durations off a little o and instant is right I am loving this thanks a bu...
- Mon May 01, 2017 11:42 am
- Forum: openTx
- Topic: Sequencing
- Replies: 7
- Views: 5190
Re: Sequencing
Thank you for the response JSA and Wineguy. I found another way as well I see logical switches would also work. and maybe better but how do I set the value of a logical switch? can you show me? I used a couple of unused channels and had them change value on a delay then used them in the mix for the ...
- Sun Apr 30, 2017 3:37 am
- Forum: openTx
- Topic: Sequencing
- Replies: 7
- Views: 5190
Sequencing
I am going crazy. on my old DX9 I could use sequencing to pull the choke on and off. I would ram the choke all the way open than back off the servo off slightly so there wouldn't be any drag on the servo. I did the same thing closing it. I cannot for the life of me figure out how to create a sequenc...