Search found 10 matches

by drummaker
Mon Jan 15, 2018 2:47 pm
Forum: Reviews
Topic: Review: FRSKY S8R Receiver
Replies: 22
Views: 18254

Re: Review: FRSKY S8R Receiver

Does anyone know of a way to bind the S8R in non telemetry mode?

IE no telemetry from receiver...
This would make it work with redundancy bus
by drummaker
Mon Jan 15, 2018 2:33 pm
Forum: General help (FrSky Taranis radio)
Topic: Slider switches on Taranis sides ???.
Replies: 9
Views: 5389

Re: Slider switches on Taranis sides ???.

sorry about the delay 2.2 is the version

You cannot find them in drop down in most places
by drummaker
Sat Jan 13, 2018 3:07 pm
Forum: General help (FrSky Taranis radio)
Topic: X** servo travel
Replies: 2
Views: 1018

Re: X** servo travel

Never mind I thought I was using a s8r and x8r but was using 2 s8rs and had not set limits by system reset



anyone know if telemetry can be disabled on S8R?
by drummaker
Sat Jan 13, 2018 2:58 pm
Forum: General help (FrSky Taranis radio)
Topic: X** servo travel
Replies: 2
Views: 1018

X** servo travel

I just recently noticed something which is quite odd when I bind X series (includes S series as well) the servo stops moving when the value for the channel is about 70% I have verified this is not the servo limit by binding Spektrum receiver to the taranis with spektrum module.... The servo travels ...
by drummaker
Wed Jul 19, 2017 1:37 am
Forum: openTx for FrSky radios
Topic: telemetry lost
Replies: 1
Views: 3070

telemetry lost

I am constantly getting telemetry lost telemetry recovered.... I have been flying with s6rs lately and haven't gone out with any x8r receivers for a while... Does anyone know if there is a s6r bug? or is there a seperate antenna for telemetry in the transmitter.. perhaps a loose connection I will st...
by drummaker
Fri May 19, 2017 4:35 pm
Forum: General help (FrSky Taranis radio)
Topic: Slider switches on Taranis sides ???.
Replies: 9
Views: 5389

Re: Slider switches on Taranis sides ???.

Why are RS and LS not supported on TX companion?
by drummaker
Mon May 01, 2017 5:30 pm
Forum: openTx
Topic: Sequencing
Replies: 7
Views: 2393

Re: Sequencing

Here is a new way WOW Lots of ways.... I really didn't have a full grasp on the logical switches or on MAX which I really wish they would just let you type in a value instead of having to mess with offset. but Hey. How am I to argue with the braniacs that came up with this stuff. logical switches Lo...
by drummaker
Mon May 01, 2017 4:11 pm
Forum: openTx
Topic: Sequencing
Replies: 7
Views: 2393

Re: Sequencing

I really do appreciate the response and understand what you are saying but the real thing I am actually trying to do now is below. I was trying to simplify so I didn't have to explane Wow Edge is the answer though you got the durations off a little o and instant is right I am loving this thanks a bu...
by drummaker
Mon May 01, 2017 11:42 am
Forum: openTx
Topic: Sequencing
Replies: 7
Views: 2393

Re: Sequencing

Thank you for the response JSA and Wineguy. I found another way as well I see logical switches would also work. and maybe better but how do I set the value of a logical switch? can you show me? I used a couple of unused channels and had them change value on a delay then used them in the mix for the ...
by drummaker
Sun Apr 30, 2017 3:37 am
Forum: openTx
Topic: Sequencing
Replies: 7
Views: 2393

Sequencing

I am going crazy. on my old DX9 I could use sequencing to pull the choke on and off. I would ram the choke all the way open than back off the servo off slightly so there wouldn't be any drag on the servo. I did the same thing closing it. I cannot for the life of me figure out how to create a sequenc...

Go to advanced search