openrcforums

WORKS! Upgrading the XSR to the current firmware did the trick. Funny how that works. thanks for your help, love me some ErSky9x.

w

And on that note, is it possible to upgrade the firmware to the XSR using a 9xtreme w XJT ? Most of the upgrade methods out there involve a Taranis...and there's s.port pins on the XJT...

starting to think it's a firmware issue on the XSR lemme work on that before you spend any more time on this

oh yea, good idea. still a bit early over here. This article https://blck.mn/2016/06/smartport-the-frsky-xsr-and-betaflight/ mentions that SmartPort turns off after 5 seconds if it doesn't get a return signal. Since I know my radio works perfectly with the BetaFlight FC, the problem must be with the...

OK, here's the new file.
Please note, This file was created as a .RAW file, the previous ones were .CSV and this website doesn't want to let me upload .RAW files, so I changed the extension to .TXT so be sure to change it back to .raw before viewing.
also, thanks a bunch for doing this

w

No, they stay gone.

Also, I installed the ersky9x9XT_rom before reading that you specified the ersky9x_rom should I try the other?

The tick marks show up one by one, the voltage shows 8.7 - 11.5v (battery is 11.3v) and about 5 seconds later all the tick marks go out at once. I did this with a quad built arount a betaflight f3 and XSR and all the ticks stay on, so I know the radio's working fine. Something about the f4 ?

https://youtu.be/T0C88bCa2ZY
here's a vid

I've had a quick look and the raw telemetry data looks OK, it should get decoded correctly. The telemetry item "BATT" is the transmitter battery, is this the value that shows 12.4v? What revision of ersky9x do you have on the radio? Mike. Version V. 1764-Mike Ersky9x-r220 When I first tur...

0MNI_F4PRO-2017-08-11.csv Go here for instructions on how to enable "raw logging", get a log file and post it on here: http://openrcforums.com/forum/viewtopic.php?f=7&t=40&p=123508&hilit=raw+logging#p123508 . The DEBUG menu is UP LONG, then RIGHT a few times. Note that the &qu...

Go here for instructions on how to enable "raw logging", get a log file and post it on here: http://openrcforums.com/forum/viewtopic.php?f=7&t=40&p=123508&hilit=raw+logging#p123508 . The DEBUG menu is UP LONG, then RIGHT a few times. Note that the "raw logging" optio...

jhsa wrote: ↑Thu Aug 10, 2017 3:09 pm What do you mean by "traditional FrSky telemetry"?

João

If I select FrSky instead of SmartPort in the Ports tab, can I use that, or do I have to use SmartPort?

jhsa wrote: ↑Thu Aug 10, 2017 2:17 pm Does that flight controller really send s.port data??

João

Can the XJT module receive traditional FrSky telemetry in D16 mode ?

Go here for instructions on how to enable "raw logging", get a log file and post it on here: http://openrcforums.com/forum/viewtopic.php?f=7&t=40&p=123508&hilit=raw+logging#p123508 . The DEBUG menu is UP LONG, then RIGHT a few times. Note that the "raw logging" optio...

jhsa wrote: ↑Thu Aug 10, 2017 2:17 pm Does that flight controller really send s.port data??

João

I'm doing everything in this video
https://youtu.be/8sqivY8deT0
Except using the 9xtreme instead of a Taranis, so I don't have the New Sensor Scan

Ok, I played around with it a bit last night. All the different PROTO settings, INVERT COM on and off for each, tried each of the Baud rates in the Configurator. When powering up, I would sometimes get correct vBAT and Alt, but a few seconds later Alt would go to 3,000m and the Voice says No Telemet...

Sorry, the RSSI value is correct. When SmartPort is disabled, I get RSSI and everything else (Alt, Ctot, vBAT) are all Zero. When I turn on SmartPort, RSSI is still good but Alt is 3,000m and vBAT shows 12.4v no matter what the actual voltage is. I'm heading to work, I'll check the Tx setup tonight....

yes, I get RSSI, and I get numbers when I enable SmartPort, but they're wrong, the Vfas is wrong and the Voice says No Telemetry.

I am trying to get the XJT to work, everything works when I'm in D8

Hey guys, trying to get my telemetry to work on a new racing quad with the Omnibus F4 Pro V3. My radio is the 9X with the 9xtreme board and an XJT. I've soldered the telemetry wires to pin 5 so I get full telemetry, and I have another XSR hooked up to a Betaflight F3 and get full telemetry from that...

Hey guys, thanks for the great post. I've been working on the mod and noticed strange behavior. Initially I only hooked up the TX side of things, wiring the TX pin to pin 5 in the module and then in the case connecting pin 5 to the black wire on the 9xtreme board. I'm getting a RSSI value, but it wa...