Search found 126 matches

by michel49
Wed Jun 12, 2019 9:53 am
Forum: OpenXVario - an open source vario supported by the open source firmwares!!
Topic: 80-100 amp sensor
Replies: 1
Views: 177

80-100 amp sensor

I can see there is only two current sensors in the "X" range FrSky Rxs: 40 & 150; is it possible to buils a compatible 80-100 current sensor ?

MP
by michel49
Sun Feb 24, 2019 2:38 pm
Forum: Hardware
Topic: 9XR Pro appears to be dead!
Replies: 11
Views: 490

Re: 9XR Pro appears to be dead!

Try to short it
by michel49
Tue Feb 05, 2019 1:56 pm
Forum: OpenXVario - an open source vario supported by the open source firmwares!!
Topic: analog baro
Replies: 2
Views: 238

Re: analog baro

thanks mstrens, that is what I need; I always used an arduino with my Jeti sensors 'RCthoughts), I own many pro-mini, will it be good ?

the input of my OSD can run up to 3.3 volts, it would be good to match 330 meters

I wait your input

Thanks

MP
by michel49
Mon Feb 04, 2019 9:23 am
Forum: OpenXVario - an open source vario supported by the open source firmwares!!
Topic: analog baro
Replies: 2
Views: 238

analog baro

Hi,

I own an OSD which include a GPS which is not very accurate, is there a way to add an analog baro to one of the analog inputs ? a brand one or DIY one.

Thanks

MP
by michel49
Wed Nov 14, 2018 4:26 pm
Forum: Other Electronic Projects
Topic: RF Module Soft Power Switch for AR9x, Skyboard, 9XR-PRO
Replies: 61
Views: 15219

Re: RF Module Soft Power Switch for AR9x, Skyboard, 9XR-PRO

Joao

please let me know if you have a file to send a PCB maker in China

MP
by michel49
Wed Nov 14, 2018 3:58 pm
Forum: Turnigy 9XR PRO radio
Topic: Protocol PPM ????
Replies: 9
Views: 1798

Re: Protocol PPM ????

Thanks Joao; amazing to see how much work to do to replace a toggle switch...
by michel49
Wed Nov 14, 2018 1:18 pm
Forum: Turnigy 9XR PRO radio
Topic: Protocol PPM ????
Replies: 9
Views: 1798

Re: Protocol PPM ????

Sorry, forgot it: Ersky9x; I want to install a Jeti box Profi on the top of the box, very easy since there is no antenna and I get telemetry on the Jeti box.
I'm confused about the purpose of the menu: internal/external ? what it does ? switching PPM signal ? or is it possible to switch power ?

MP
by michel49
Wed Nov 14, 2018 9:54 am
Forum: Turnigy 9XR PRO radio
Topic: Protocol PPM ????
Replies: 9
Views: 1798

Re: Protocol PPM ????

I wish to install a second (internal) module; where I can wire it ? I can see an encoder connector on the main board ? and what about the power connection ? will it be switched by the internal/external menu ?

Thanks Joao to help me

MP
by michel49
Tue Nov 13, 2018 2:54 pm
Forum: openTx
Topic: AFHDS2A telemetry
Replies: 0
Views: 1059

AFHDS2A telemetry

After flashing the 4IN1 328P module on my Horus OTX 2.2 with the latest FW 1.2.1.10 I can get the FS-CVT01 sensor but not the TGY-CAT01 (alitude),what I can do ?
by michel49
Sun Oct 14, 2018 3:07 pm
Forum: ersky9xr
Topic: bug ?
Replies: 1
Views: 448

bug ?

Maybe a bug with ERSKY9X: I took an old D8RSP and I was not able to bind with both my 9XR PRO and my TH9X/AR9X; it bind only in PPM mode with DJT/XJT module and my OpenTX/Horus10.
by michel49
Thu Oct 11, 2018 6:22 pm
Forum: General RC Electronic Projects and Discussion
Topic: SBUS Servo Configuration Protocol
Replies: 5
Views: 1587

Re: SBUS Servo Configuration Protocol

I checked it don't work with Corona Sbus servos.
by michel49
Thu Sep 13, 2018 1:02 pm
Forum: Electronic Mods
Topic: Turnigy 9X 9Ch / 16 channels?
Replies: 15
Views: 4948

Re: Turnigy 9X 9Ch / 16 channels?

I remember tried the TH9X with a Jeti and Orange module working fine with 12 ch.Rxs
by michel49
Wed Aug 29, 2018 7:47 am
Forum: FRSky Horus radio
Topic: 6 positions switch
Replies: 2
Views: 927

Re: 6 positions switch

Thanks Mike; I had not the idea...

MP
by michel49
Wed Aug 22, 2018 6:32 pm
Forum: openTx
Topic: Horus 6 pos switch
Replies: 1
Views: 373

Horus 6 pos switch

Is there a way to set the 6 pos switch in order to act like a pot? since this is the way expected by my flight controller and a real pot give not secure positions.It would be increment from -100 to +100 divided by 5 segments.
by michel49
Sun Aug 19, 2018 2:42 pm
Forum: FRSky Horus radio
Topic: 6 positions switch
Replies: 2
Views: 927

6 positions switch

I need to use the the 6P switch to choose between the 6 flight modes on my FC; how to set it in order each position match a position between 1000 and 2000ùS ?

MP
by michel49
Fri Aug 03, 2018 2:23 pm
Forum: Turnigy 9XR PRO radio
Topic: Wierd issue with right gimbal
Replies: 82
Views: 10888

Re: Wierd issue with right gimbal

On my stick one of the pins of the pot was not crimped properly, not the case which moved.
by michel49
Sun May 27, 2018 12:37 pm
Forum: General RC Electronic Projects and Discussion
Topic: Arduino - Extend the number of servos supported by a Rx
Replies: 101
Views: 23069

Re: Arduino - Extend the number of servos supported by a Rx

It is easy to find S-bus servos but I'm sorry S-bus Esc don't exist.
by michel49
Mon May 14, 2018 12:42 pm
Forum: ersky9xr
Topic: FrSky alt sensor
Replies: 10
Views: 1504

Re: FrSky alt sensor

Yes it is connected, and as I told it works with Horus/internal module/Opentx

maybe the "Alt" option in the telemetry menu of the 9XR-Pro match only the Sport connection ?
by michel49
Sun May 13, 2018 11:12 am
Forum: ersky9xr
Topic: FrSky alt sensor
Replies: 10
Views: 1504

Re: FrSky alt sensor

Thanks Mike, I have to add the telemetry works fine except the vario sensor; I get RSSI and voltage sensor linked to A1; I checked an other old glider with the same Rx?sensor with the same result. Of course at the time I flew those gliders the MM. don't exist...when I tell it works with Opentx it us...
by michel49
Fri May 11, 2018 7:49 am
Forum: ersky9xr
Topic: FrSky alt sensor
Replies: 10
Views: 1504

Re: FrSky alt sensor

Yes, I use an old glider with the vario sensor plugged on the A2 port of the "D" Rx and the multi module 9XRPRO; what is strange is the last time I fly it it worked fine but, of course, not with the multi module. I will give it a try with the XJT module.
by michel49
Tue May 08, 2018 7:29 am
Forum: ersky9xr
Topic: FrSky alt sensor
Replies: 10
Views: 1504

Re: FrSky alt sensor

Thanks Mike, of course it is the vario sensor, but I need to display the altitude; I remember it worked some (!) years ago with an old FW...
by michel49
Sun May 06, 2018 7:27 am
Forum: ersky9xr
Topic: FrSky alt sensor
Replies: 10
Views: 1504

FrSky alt sensor

I can't find how to set the telemetry menu of the 221 FW to make the alt sensor work when linked with the A2 input of the D8 Rx; it works fine with my OpenTx Horus.
by michel49
Fri Mar 09, 2018 1:51 pm
Forum: Turnigy 9XR PRO radio
Topic: Banggood 4in1 module, Flysky AFHDS2A and Telemetry
Replies: 173
Views: 13417

Re: Banggood 4in1 module, Flysky AFHDS2A and Telemetry

OK Mike, I will do that but I do apologosise for the delay: in my french farwest the web don't work all the days...
If you agree I could send you the Rx and the sensors, it would be easier, I purchased it just for experimentation.

MP
by michel49
Thu Mar 08, 2018 9:02 am
Forum: Turnigy 9XR PRO radio
Topic: Banggood 4in1 module, Flysky AFHDS2A and Telemetry
Replies: 173
Views: 13417

Re: Banggood 4in1 module, Flysky AFHDS2A and Telemetry

I use the FS-CVT01 (voltage) & TGY-CAT01 (altitude).

MP
by michel49
Wed Mar 07, 2018 1:21 pm
Forum: Turnigy 9XR PRO radio
Topic: Banggood 4in1 module, Flysky AFHDS2A and Telemetry
Replies: 173
Views: 13417

Re: Banggood 4in1 module, Flysky AFHDS2A and Telemetry

I just flashed the 221g6 fw on my 9XRPRO and I can only display rssi 75, tssi 246 and Rx voltage but none of my two sensors; I use both STM and 328 4-1 module.
Is there something to do ?
by michel49
Fri Feb 16, 2018 2:32 pm
Forum: ersky9xr
Topic: RSSI
Replies: 4
Views: 698

Re: RSSI

Thanks Joao, not as easy as OpenTx but it should work...

MP
by michel49
Fri Feb 16, 2018 10:01 am
Forum: ersky9xr
Topic: RSSI
Replies: 4
Views: 698

RSSI

Is there a way to redirect the RSSI signal to ch.16 ?

I know howto do that with the input menu with OpenTx but don't know with ER9XR

MP
by michel49
Fri Jan 05, 2018 10:03 am
Forum: Other Electronic Projects
Topic: 3D PRINTING for RC Hobby (CR10 3D Printer)
Replies: 52
Views: 5378

Re: 3D PRINTING (RC Hobby for 3D Printers)

I made it with some pieces of carbon sheet:
by michel49
Thu Aug 31, 2017 6:32 pm
Forum: UPGRADE BOARDS
Topic: AR9x board and what are options on FW
Replies: 14
Views: 4525

Re: AR9x board and what are options on FW

I use eepeskye ver.4.15; is that an issue ?
by michel49
Thu Aug 31, 2017 6:28 pm
Forum: UPGRADE BOARDS
Topic: AR9x board and what are options on FW
Replies: 14
Views: 4525

Re: AR9x board and what are options on FW

Thanks Joao but that don't work, the BL stays at 1.9; I can only go up to C8; if I flash the E3 I get a snowy screen and I can't stop with the on/off switch.

MP

Go to advanced search