Search found 178 matches
- Tue Feb 02, 2021 3:02 pm
- Forum: Hardware
- Topic: X8R burned regulator
- Replies: 6
- Views: 1046
Re: X8R burned regulator
Yes, I bought a wired (TO5 ?) regulator because the tracks of the SMD was destroyed.
- Thu Dec 17, 2020 4:53 pm
- Forum: Hardware
- Topic: X8R burned regulator
- Replies: 6
- Views: 1046
Re: X8R burned regulator
Nope, issue fixed !
- Wed Dec 16, 2020 8:52 am
- Forum: ersky9xr
- Topic: AFHDS-2A telemetry
- Replies: 2
- Views: 1281
Re: AFHDS-2A telemetry
Thanks Mike, I 'll try that
MP
MP
- Tue Dec 15, 2020 3:59 pm
- Forum: ersky9xr
- Topic: AFHDS-2A telemetry
- Replies: 2
- Views: 1281
AFHDS-2A telemetry
I use the TH9X/AR9X with the last FW 223 and the STM32 multi-module with the last FW. I get RSSI and volt sensor but not the alt sensor; in the telemetry menu I selected the AFHDS2 option; is there a parameter wrong ? I get the alt sensor with Opentx and this module; I guess there is a bad parameter...
- Thu Dec 10, 2020 12:27 pm
- Forum: openTx
- Topic: Jeti Duplex telemetry
- Replies: 6
- Views: 905
Re: Jeti Duplex telemetry
OK Kilrah, a good challenge, isn't ?
- Wed Dec 09, 2020 10:07 am
- Forum: openTx
- Topic: Jeti Duplex telemetry
- Replies: 6
- Views: 905
Re: Jeti Duplex telemetry
I'm not sure to understand the goal of the electronics described; I hoped a simpler way where the data wire of the Jeti module was linked to pin 5 of the JR bay like the 4in1 module do and OTX translate the telemetry datas stream in the same way as Spektrum or AFHDS2A .
- Tue Dec 08, 2020 10:01 am
- Forum: openTx
- Topic: Jeti Duplex telemetry
- Replies: 6
- Views: 905
Re: Jeti Duplex telemetry
Thank you kalle
- Mon Dec 07, 2020 4:55 pm
- Forum: openTx
- Topic: Jeti Duplex telemetry
- Replies: 6
- Views: 905
Jeti Duplex telemetry
I have a Jeti module -the old one-, would it be possible to get and display the telemetry datas with OTX ?
MP
MP
- Sat Nov 21, 2020 1:16 pm
- Forum: Turnigy 9XR PRO radio
- Topic: Banggood 4in1 module, Flysky AFHDS2A and Telemetry
- Replies: 189
- Views: 47564
Re: Banggood 4in1 module, Flysky AFHDS2A and Telemetry
Hi Mike,
In the OpenTx thread you will find a link given by Kilrah about the issue encountered by Hpnuts following 2A sensors.
In the OpenTx thread you will find a link given by Kilrah about the issue encountered by Hpnuts following 2A sensors.
- Thu Nov 19, 2020 12:05 pm
- Forum: Hardware
- Topic: X8R burned regulator
- Replies: 6
- Views: 1046
Re: X8R burned regulator
Thanks Kalle, I did not know the matricule of this chip; unfortunately since some tracks are destroyed I need a regulatot with wires in order to solder two on the connector block and the third direct on the PCB. Regulator ordered at Ebay .
MP
MP
- Wed Nov 18, 2020 2:11 pm
- Forum: Hardware
- Topic: X8R burned regulator
- Replies: 6
- Views: 1046
X8R burned regulator
After a Bec failure I have a 3.3volts regulator burned; what chip I could purchase in TO92 case ?
Thanks
Thanks
- Wed Nov 18, 2020 8:21 am
- Forum: OpenXVario - an open source vario supported by the open source firmwares!!
- Topic: AFHDS-2A telemetry
- Replies: 1
- Views: 313
AFHDS-2A telemetry
The AFHDS-2A sensor range is not comprehensive; I would like a RPM BL sensor and a Amp sensor recognised by OTX, do you think it is possible with oXs ?
MP
MP
- Tue Nov 17, 2020 4:35 pm
- Forum: openTx
- Topic: AFHDS-2A telemetry
- Replies: 9
- Views: 786
Re: AFHDS-2A telemetry
Oupss, sorry Kilrah, I was wrong , I discovered the Alt sensor, and the atmospheric pressure!
Thanks for your help
MP
Thanks for your help
MP
- Tue Nov 17, 2020 2:27 pm
- Forum: openTx
- Topic: AFHDS-2A telemetry
- Replies: 9
- Views: 786
Re: AFHDS-2A telemetry
OK updated both OTX and module (STM32)....but no CAT01 sensor...
- Sat Nov 14, 2020 2:26 pm
- Forum: openTx
- Topic: AFHDS-2A telemetry
- Replies: 9
- Views: 786
Re: AFHDS-2A telemetry
OK, I changed the PC and now the Horus is flashed with the 2.3.10 FW but now it ask to update the multi-module, howto ? with Companion ? it is the 328 one.
- Sat Nov 14, 2020 12:26 pm
- Forum: openTx
- Topic: AFHDS-2A telemetry
- Replies: 9
- Views: 786
Re: AFHDS-2A telemetry
I guess you tell "Tx off" ?
When I do that I see the transfer is instantly on the PC screen....but the FW remain the same (2.2.1)
I get the message
Filter on vendor = 0x0483 product = 0xdf11
More than one DFU capable USB device found, you might try `--list' and then disconnect all but one device
When I do that I see the transfer is instantly on the PC screen....but the FW remain the same (2.2.1)
I get the message
Filter on vendor = 0x0483 product = 0xdf11
More than one DFU capable USB device found, you might try `--list' and then disconnect all but one device
- Sat Nov 14, 2020 9:14 am
- Forum: openTx
- Topic: AFHDS-2A telemetry
- Replies: 9
- Views: 786
Re: AFHDS-2A telemetry
I have an issue to flash my X10: I have the usb logo on the screen but Companion tell me "not connected, driver not installed
very strange since I can read the models ...
very strange since I can read the models ...
- Fri Nov 13, 2020 9:20 am
- Forum: openTx model setup
- Topic: 2 EDF's, 2 ESC's one battery on two throttle channels!
- Replies: 3
- Views: 867
Re: 2 EDF's, 2 ESC's one battery on two throttle channels!
I have the same, be careful to have the same RPM since tere is no rudder to roll on the track
- Fri Nov 13, 2020 9:17 am
- Forum: openTx
- Topic: AFHDS-2A telemetry
- Replies: 9
- Views: 786
AFHDS-2A telemetry
I just tried the AFHDS-2A iA6B Rx with my Horus/4in1 module/OTX 2.2.1.
I get RSSI and CVT01 but not the CAT01 sensor, what I can do ?
Thanks
MP
I get RSSI and CVT01 but not the CAT01 sensor, what I can do ?
Thanks
MP
- Tue Nov 03, 2020 12:18 pm
- Forum: OpenXVario - an open source vario supported by the open source firmwares!!
- Topic: OpenXSensor project page on google code
- Replies: 139
- Views: 70985
Re: OpenXSensor project page on google code
Thanks mstrens, I just want to monitor the pack voltage; could you tell me which electronics to use ? I just know the vario board.
- Tue Nov 03, 2020 11:03 am
- Forum: OpenXVario - an open source vario supported by the open source firmwares!!
- Topic: OpenXSensor project page on google code
- Replies: 139
- Views: 70985
Re: OpenXSensor project page on google code
Hi,
Is there a way to build a simple 12S Sport voltage sensor ? that doesn't exist in FrSky range
Is there a way to build a simple 12S Sport voltage sensor ? that doesn't exist in FrSky range
- Tue Nov 03, 2020 11:01 am
- Forum: Turnigy 9XR PRO radio
- Topic: 9XR-Pro into Vintage Futaba FP Build, questions and progress pics!
- Replies: 21
- Views: 2746
Re: 9XR-Pro into Vintage Futaba FP Build, questions and progress pics!
The best DIY Tx I made is the AR9X board associated with the 4-1 module and the screen on the top; at last I can take a glance when in flight !
ERsky9X is btw the most intuitive and ergonomic FW ; thanks Mike.
ERsky9X is btw the most intuitive and ergonomic FW ; thanks Mike.
Re: csv.file
Many thanks, that is OK
MP
MP
Re: csv.file
Well, I have an issue, the flash stop before the end; I know the issue come from the bootloader but I don't know how to update it...
MP
MP
Re: csv.file
Hi Mike
Ihave a TH9X/AR9x , can I flash the same FW as the PRO one ?
MP
Ihave a TH9X/AR9x , can I flash the same FW as the PRO one ?
MP
Re: csv.file
Very good, thanks
MP
MP
Re: csv.file
Thanks Mike, I will try that...
I thought about the Companion module but, for some reason, it doesnot accept the .csv file recorded with the PRO; is there a way to simply mod the file to be compatible ?
MP
I thought about the Companion module but, for some reason, it doesnot accept the .csv file recorded with the PRO; is there a way to simply mod the file to be compatible ?
MP
Re: csv.file
I have Open Office but I don't know how to use it to display grahical .csv files; maybe there is a lighter software, just a simple module dedicated to such a simple work ?
csv.file
Which PC software I could use to display easily the graphic datas recorded with my PRO ?
Thanks
MP
Thanks
MP
- Thu Sep 24, 2020 8:39 am
- Forum: FRSky Horus radio
- Topic: Differental Steering
- Replies: 2
- Views: 620
Re: Differental Steering
I had the same problem with the tracks of a model tank; you can solve with adding a curve on each throttle mixing