openrcforums

Taranis X9D plus here.. This began a couple days ago.. i was gonna fly like allways and noticed there was no data from telemetry.. not RSSI, no voltage.. nothing.. i could switch off the radio without the warning about model still on .. then switched it off and on again and it came back.. tought it ...

Did you set up the PPM frame?

When i moved to the Taranis from my older 9X my FlySky and DMS2 modules wouldnt work just setting the modules to external and PPM

i had to put also 8 channels and 22.5ms 300u and - in PPM frame..

try this maybe..

today i noticed the 2.1.0 firmware is finally avalaible for the XM .. so flashed it to 2.1.0 and bingo! Now it binds and i get a green light on startup ..

Finally..it took me literally like 2 years to get this binded

Thanks

Well thats a bit dissapointing as on 2.0 they were quite easy to setup.. at least i can do a setup with LS and then copy it to the rest of models with analog sensor

Sorry if this has been covered.. i have searched for hours arround the forums and readed the 2.2 manual. I recently upgraded from 2.0.16 to 2.2.4 .. i knew Telemetry would need to be redone complety.. all planes i monitor the battery voltage i use (so far) D receivers with the good old analog voltag...

maybe set a Logical switch for each callout position.. like A=X (or A > X so it triggers when it goes past that value) and then a special function to talk when the logical switch is triggered?

i did a quick simulation and could had 2 sounds played in 2 positions of the slider

Since you updated your internal module to ACCST 2.1 all your 2.4GHz receivers must be updated to that as well, but there is no ACCST 2.1 firmware available for the XM yet. I noticed that my older X8R doesnt bind either but it gives the both leds on error.. all D and L9R Rxs work tought.. so its a t...

I have had this XM receiver for like 3 years now and never been able to bind it... First i knew why.. i had 2.0.16 firm on my Taranis (FCC) and when trying to bind the XM would return both leds light fixed , red and green , wich looking arround means incompatible firmware (usually FCC/LBT conflict b...

Also all Taranis here run OpenTX .. so its also a matter of comonality :D I rstill un Er9X in my old 9X wich is still in the closet after i got the X9D .. i keep it as a backup radio.. i never had complains about er9X and actually thanks it because its so similar to OpenTX that i didnt had any issue...

2.2 does a better job of conversion than 2.1 did. Sliders seem to be the only real problem, if you use a slider for flaps, check that function carefully. Thats what worries me ... i use sliders for crow brakes in 3 gliders..one of them even uses both sliders.. left for crow and right for camber/ref...

1. You will need to redo any telemetry as that is now quite different. However they sensors you have work fine. yeah... for now i only use telemetry for the RSSI and voltage sensor with basic alarms.. so redoing stuff from scratch should be easy.. not using anything complex.. but might soon ..but f...

So .. im using 2.0.19 since the day i bought my Taranis..usually i dont like upgrading something that allready works due to very unpleasant issues in the past upgrading stuff.. But now the thing is i cant use some stuff like XM series FrSky receivers and other newer ones and they wont work in 2.0.X ...

If you cannot do that, then use the Dual Rate screen to reduce the elevator input to 40%. This will reduce the servo movement caused by the stick, while leaving the trim adjustment at its full movement. Thanks... the dual rate trick works in eePee.. its allready a workarround as as you said, while ...

Im migrating my SIG Ninja glider to my er9X moded FlySky 9X with FrSky system.. so after programing mixes and airbrakes (i use 2 separate chanels for the ailerons) i check up thinks and noticed an issue.. Trim in the elevator (CH2) chanel is quite low..but in the ailerons its quite a lot. i had set-...

So when selecting switch for example ELE (elevator switch) its ELE for one position and ELE! for the other?

er9X

Oh so if i dont understand bad its basically adding 2 mixes for that chanel changing the source (AIL and RUD) and putting each on the 2 positions of a switch so it will take one source or the other depending on switch position?

This probably is a noobish question... but the search tool didnt got anything.. so sorry if its repeated.. I would like to be able to switch between 2 flight modes "in flight" ... more exactly between mode 2 and 4.. wich means swaping the ailerons - rudder between sticks Esentially i fly m...

Hi... I registered and went here directed from Rcgroups :D My 9X does exactly this thing You have the plane and radio on... you switch off the radio , nothing happens in the plane but when you switch on the radio.. until you get to the main model screen al controls center and motor spins..I would sa...