openrcforums

hi João
ok i anderstand.
In the Hardware menu i have just 2 lines:
BandGap (ticked) What is this ?
and TelemetrEZ>=r90 (ticked)
Nothing to configure extra switches.
regards
François

Hy João what is the last realise of the firmware for my old Th9x M64 moded to telemetry and arduvoice ? i use the JP4in1 module multiprotocol i have flashded er9xProv822k --> er9x-frsky-sv.hex but it sem's to be a test firmware how can i put my radio in maintenance mode to access extra switch ? it i...

Hy João

All works fine i just replace my old speaker for an other and now P1 control All voice volume.

Thank you

Hy João Thank you for your quick reply. I uploaded the wav files from the link given to me on the root of the SD card, and now the voice works. The sound volume is low and not very clear on the output of the amplifier. If i solder the same speaker on pin 5 and Gnd directly to the arduino the voice i...

Hello I have a Turnigy 9x whith M64 processor. I have build the 2 boards of Arduvoice but not voice listening and BackLight stay always On. Trim Ok, backup, Restore, Delete Ok Beep Ok but very low. i don't know why no Voice. Radio Setup / Audio Haptic" menu set the "Sound Mode" to &qu...

"Range Check" mode 10m const PPM_Parameters PPM_prot[15]= { // Dial Protocol Sub protocol RX_Num Power Auto Bind Option /* 1 */ {MODE_DSM , DSM2_22 , 0 , P_HIGH , NO_AUTOBIND , 6 }, // /* 2 */ {MODE_DSM , DSMX_22 , 0 , P_HIGH , NO_AUTOBIND , 6 }, // /* 3 */ {MODE_DSM , DSMX_11 , 0 , P_HIGH...

const PPM_Parameters PPM_prot[15]= { // Dial Protocol Sub protocol RX_Num Power Auto Bind Option /* 1 */ {MODE_DSM , DSM2_22 , 0 , P_HIGH , NO_AUTOBIND , 6 }, // /* 2 */ {MODE_DSM , DSMX_22 , 0 , P_HIGH , NO_AUTOBIND , 6 }, // /* 3 */ {MODE_DSM , DSMX_11 , 0 , P_HIGH , NO_AUTOBIND , 6 }, // /* 4 */ ...

Hi Mike
The reason is
I have flashed Multi firmware to use DSMx Whipit micro DLG.
The stock firmware not Bind with this micro glider.
Works with Multi firmware but the range is not good around 50m.
i have lost several time my DLG.

ok Mike
it's not possible to return at the original firmware ?
whith the OrangeRX USB Firmware Update Kit it's possible or not ?

Hi Mike
Do you have the stock firmware to ORx module ?
because i don't save it .
Thank you

Ok mike i found where is wrong. Is in _Config.h ! It is missing 1 after #define INVERT_TELEMETRY //Uncomment to invert the polarity of the telemetry serial signal. //For ER9X and ERSKY9X it must be commented. For OpenTX it must be uncommented. #define INVERT_TELEMETRY 1 Now all done very well 201612...

Hi Mike, mary christmas. Yes i have done a "discover sensors" on openTx 2.1.9 but nothing is detect. And yes i have choose auto-detect the format in combo box see photo. When binding in progress, beside the Module Status V1.1.1030 bind appear and disapear when the led is solid on the recei...

Hi mike i have compiled mine with the 1.1.6 source code to Uncomment the blue module in MultiOrange.cpp.orangetx // For BLUE module use: #define DSM_BLUE And yes i have inverted telemetry in _Config.h /**************************/ /*** TELEMETRY SETTINGS ***/ /**************************/ //In this se...

Hi mike, sorry for my poor english. Thank you for your good job. I modified my DIYorange module. I have flashed the MultiOrangeBlue firmware with AVR isp MkII and AVRstudio. The result is good everything works well, But on my Taranis +, i do not see telemetry when I bind a R820x V2 receiver Telemetr...